Download JNTUA (JNTU Anantapur) B.Tech R13 (Bachelor of Technology) 1st Year 1st Semester (1-1) 2017 Dec Supply 13A03101 Engineering Drawing Previous Question Paper || Download B-Tech 1st Year 1st Sem 13A03101 Engineering Drawing Question Paper || JNTU Anantapur B.Tech 1-1 Previous Question Paper || JNTU Anantapur B.Tech ME 1-1 Previous Question Paper || JNTU Anantapur B.Tech CSE 1-1 Previous Question Paper || JNTU Anantapur B.Tech Mech 1-1 Previous Question Paper || JNTU Anantapur B.Tech EEE 1-1 Previous Question Paper || JNTU Anantapur B.Tech ECE 1-1 Previous Question Paper
Code: 13A03101
B.Tech I Year (R13) Supplementary Examinations December 2017
ENGINEERING DRAWING
(Common to CE and ME)
Time: 3 hours Max. Marks: 70
(Answer all five units, 05 X 14 = 70 Marks)
*****
UNIT ? I
1 A cricket ball is thrown vertically up, it reaches a maximum height of 15 meters and falls on the ground
at a distance of 30 meters from point of projection of the ball till it reaches the ground. Draw the path
followed by the cricket ball and name the curve. Draw normal and tangent at any point on the path of
the curve.
OR
2 A circle of 40 mm diameter rolls on circumference of another circle of 150 mm diameter. Draw a curve
traced out by a point P on the circumference of rolling circle for one complete revolution. Name the
curve and draw tangent and normal to the curve at any point.
UNIT ? II
3 The distance between the end projectors of a line AB is 50 mm. Point A is 15 mm above H.P and
10 mm in front of V.P. Point B is 40 mm above H.P and 40 mm in front of V.P. Find the true length of the
line AB, the inclinations of the line AB with H.P and V.P. Locate HT and VT of the line.
OR
4 Draw the projections of a circle of 50 mm diameter resting in the H.P on a point A on the circumference,
its plane inclined at 45 degrees to the H.P and the diameter AB making 30 degrees angle with the V.P.
Also show its traces.
UNIT ? III
5 A hexagonal pyramid of base 30 mm and axis 60 mm has one of its slant edges on the H.P and inclined
at 45
0
to the V.P. Draw its projections when the base is visible.
OR
6 Draw the development of the lateral surface of the part P of the hexagonal pyramid, two sides of the
base parallel to the V.P as shown in figure. All dimensions are in cm.
Contd. in page 2
Page 1 of 2
R13
FirstRanker.com - FirstRanker's Choice
Code: 13A03101
B.Tech I Year (R13) Supplementary Examinations December 2017
ENGINEERING DRAWING
(Common to CE and ME)
Time: 3 hours Max. Marks: 70
(Answer all five units, 05 X 14 = 70 Marks)
*****
UNIT ? I
1 A cricket ball is thrown vertically up, it reaches a maximum height of 15 meters and falls on the ground
at a distance of 30 meters from point of projection of the ball till it reaches the ground. Draw the path
followed by the cricket ball and name the curve. Draw normal and tangent at any point on the path of
the curve.
OR
2 A circle of 40 mm diameter rolls on circumference of another circle of 150 mm diameter. Draw a curve
traced out by a point P on the circumference of rolling circle for one complete revolution. Name the
curve and draw tangent and normal to the curve at any point.
UNIT ? II
3 The distance between the end projectors of a line AB is 50 mm. Point A is 15 mm above H.P and
10 mm in front of V.P. Point B is 40 mm above H.P and 40 mm in front of V.P. Find the true length of the
line AB, the inclinations of the line AB with H.P and V.P. Locate HT and VT of the line.
OR
4 Draw the projections of a circle of 50 mm diameter resting in the H.P on a point A on the circumference,
its plane inclined at 45 degrees to the H.P and the diameter AB making 30 degrees angle with the V.P.
Also show its traces.
UNIT ? III
5 A hexagonal pyramid of base 30 mm and axis 60 mm has one of its slant edges on the H.P and inclined
at 45
0
to the V.P. Draw its projections when the base is visible.
OR
6 Draw the development of the lateral surface of the part P of the hexagonal pyramid, two sides of the
base parallel to the V.P as shown in figure. All dimensions are in cm.
Contd. in page 2
Page 1 of 2
R13
Code: 13A03101
UNIT ? IV
7 Draw the isometric view of the object whose orthographic projections are given in the figure below. All
dimensions are in mm.
OR
8 Draw the front view, top view and side view of the object whose isometric view is shown in the figure
below (All dimensions are in mm).
UNIT ? V
9 A cone base 60 mm diameter and axis 70 mm long, rests with its base on H.P. It is penetrated by a
horizontal cylinder of 36 mm diameter. The axis of the cylinder is parallel to V.P., 25 mm above the base
and 8 mm in front of the axis of the cone. Draw the curves of intersection.
OR
10 A pentagonal lamina of 30 mm sides stands vertically on the ground plane with one of its corners on the
ground such that the side opposite to this corner is parallel to the ground plane. The lamina is inclined at
to the picture plane. The corner nearest to the picture plane is 20 mm behind it. The station point is
40 mm in front of the picture plane, 55 mm above the ground plane and passes through the centre of
the lamina. Draw the perspective view.
*****
Page 2 of 2
R13
FirstRanker.com - FirstRanker's Choice
This post was last modified on 11 September 2020