Download JNTUA (JNTU Anantapur) B.Tech R15 (Bachelor of Technology) 1st Year 1st Semester (1-1) 2017 Dec Supple 15A03101a Engineering Drawing Previous Question Paper || Download B-Tech 1st Year 1st Sem 15A03101a Engineering Drawing Question Paper || JNTU Anantapur B.Tech R15 1-1 Previous Question Paper || JNTU Anantapur B.Tech ME 1-1 Previous Question Paper || JNTU Anantapur B.Tech CSE 1-1 Previous Question Paper || JNTU Anantapur B.Tech Mech 1-1 Previous Question Paper || JNTU Anantapur B.Tech EEE 1-1 Previous Question Paper || JNTU Anantapur B.Tech ECE 1-1 Previous Question Paper
Code: 15A03101a
B.Tech I Year I Semester (R15) Regular & Supplementary Examinations December 2017
ENGINEERING DRAWING
(Civil Engineering)
Time: 3 hours Max. Marks: 70
(Answer all five units, 05 X 14 = 70 Marks)
*****
UNIT ? I
1 A circle of 50 mm diameter rolls along a line. A point on the circumference of the circle is in contact with
the line in the beginning and after one complete revolution. Draw the cycloidal path of the point. Draw a
tangent and normal at any point on the curve.
OR
2 Draw a pair of hyperbola, the distance between the foci is 75 mm and the length of the transverse axis
50 mm. Find the eccentricity of the curve.
UNIT ? II
3 Construct a forward vernier scale to read distances correct to a decameter on a map in which the actual
distances are reduced in the ratio of 1:40000. The scale should be long enough to measure 6 km. Mark
on the scale the lengths of 3034 km and 0.57 km.
OR
4 (a) A point P is 40 mm infront of VP, 50 mm above HP and 60 mm infront of right PP. Draw its projections.
(b) A point lies on HP, 40 mm infront of VP and 50 mm infront of right profile plane. Draw its projections
UNIT ? III
5 Draw the projections of a straight line AB, 100 mm long inclined at 45 to HP and 30 to VP, the end A is
in HP and the end B is in VP. Find the shortest distance between the straight line AB and the line of
intersection of planes of projection.
OR
6 A circular lamina of 60 mm diameter rests on HP such that the surface of the lamina is inclined at 30 to
HP. The diameter through the point on which the lamina rests on HP, appears to be inclined at 30 to
VP in the top view. Obtain its projections.
UNIT ? IV
7 Draw the projections of a right pentagonal prism 20 mm side of base and axis 40 mm long resting on a
corner such that the two base edges passing through it make equal inclinations with HP and its base is
inclined at 60 to HP and the axis appears to be inclined at 30 to the VP in the top view.
OR
8 Draw the development of the lateral surface of the square pyramid of side of base 30 mm and axis
40 mm, resting on HP with one of the base edges parallel to VP.
UNIT ? V
9 A combination of the solids is formed as follows. A frustum of a cone 25 mm top diameter 50 mm bottom
diameter and 50 mm high is placed vertically on a cylindrical block of 75 mm diameter and 25 mm thick
such that both the solids have the common axis. Draw the isometric projection of the combinations of
the solids.
OR
Contd. in page 2
Page 1 of 2
R15
FirstRanker.com - FirstRanker's Choice
Code: 15A03101a
B.Tech I Year I Semester (R15) Regular & Supplementary Examinations December 2017
ENGINEERING DRAWING
(Civil Engineering)
Time: 3 hours Max. Marks: 70
(Answer all five units, 05 X 14 = 70 Marks)
*****
UNIT ? I
1 A circle of 50 mm diameter rolls along a line. A point on the circumference of the circle is in contact with
the line in the beginning and after one complete revolution. Draw the cycloidal path of the point. Draw a
tangent and normal at any point on the curve.
OR
2 Draw a pair of hyperbola, the distance between the foci is 75 mm and the length of the transverse axis
50 mm. Find the eccentricity of the curve.
UNIT ? II
3 Construct a forward vernier scale to read distances correct to a decameter on a map in which the actual
distances are reduced in the ratio of 1:40000. The scale should be long enough to measure 6 km. Mark
on the scale the lengths of 3034 km and 0.57 km.
OR
4 (a) A point P is 40 mm infront of VP, 50 mm above HP and 60 mm infront of right PP. Draw its projections.
(b) A point lies on HP, 40 mm infront of VP and 50 mm infront of right profile plane. Draw its projections
UNIT ? III
5 Draw the projections of a straight line AB, 100 mm long inclined at 45 to HP and 30 to VP, the end A is
in HP and the end B is in VP. Find the shortest distance between the straight line AB and the line of
intersection of planes of projection.
OR
6 A circular lamina of 60 mm diameter rests on HP such that the surface of the lamina is inclined at 30 to
HP. The diameter through the point on which the lamina rests on HP, appears to be inclined at 30 to
VP in the top view. Obtain its projections.
UNIT ? IV
7 Draw the projections of a right pentagonal prism 20 mm side of base and axis 40 mm long resting on a
corner such that the two base edges passing through it make equal inclinations with HP and its base is
inclined at 60 to HP and the axis appears to be inclined at 30 to the VP in the top view.
OR
8 Draw the development of the lateral surface of the square pyramid of side of base 30 mm and axis
40 mm, resting on HP with one of the base edges parallel to VP.
UNIT ? V
9 A combination of the solids is formed as follows. A frustum of a cone 25 mm top diameter 50 mm bottom
diameter and 50 mm high is placed vertically on a cylindrical block of 75 mm diameter and 25 mm thick
such that both the solids have the common axis. Draw the isometric projection of the combinations of
the solids.
OR
Contd. in page 2
Page 1 of 2
R15
Code: 15A03101a
10 Figure shows the pictorial view of an object. Draw the top, front and side view. Show the dimensions of
the views.
*****
Page 2 of 2
R15
FirstRanker.com - FirstRanker's Choice
This post was last modified on 11 September 2020