FirstRanker Logo

FirstRanker.com - FirstRanker's Choice is a hub of Question Papers & Study Materials for B-Tech, B.E, M-Tech, MCA, M.Sc, MBBS, BDS, MBA, B.Sc, Degree, B.Sc Nursing, B-Pharmacy, D-Pharmacy, MD, Medical, Dental, Engineering students. All services of FirstRanker.com are FREE

šŸ“±

Get the MBBS Question Bank Android App

Access previous years' papers, solved question papers, notes, and more on the go!

Install From Play Store

Download PTU B-Tech AR-Automation-And-Robotics 2020 Dec 4th Sem 63017 Design Of Machine Elements Question Paper

Download PTU (I.K.Gujral Punjab Technical University (IKGPTU)) B-Tech (Bachelor of Technology) (AR)- Automation-And-Robotics 2020 December 4th Sem 63017 Design Of Machine Elements Previous Question Paper

This post was last modified on 13 February 2021

This download link is referred from the post: PTU B.Tech Question Papers 2020 December (All Branches)


FirstRanker.com

Total No. of Pages : 02
Total No. of Questions : 18

--- Content provided by FirstRanker.com ---

B.Tech.(Automation & Robotics) (2012 & Onward) (Sem.-4)
DESIGN OF MACHINE ELEMENTS
Subject Code : BTPE-401
M.Code : 63017
Time : 3 Hrs. Max. Marks : 60

--- Content provided by FirstRanker.com ---

INSTRUCTIONS TO CANDIDATES :

  1. SECTION-A is COMPULSORY consisting of TEN questions carrying TWO marks each.
  2. SECTION-B contains FIVE questions carrying FIVE marks each and students have to attempt any FOUR questions.
  3. SECTION-C contains THREE questions carrying TEN marks each and students have to attempt any TWO questions.

SECTION-A

--- Content provided by FirstRanker.com ---

Answer briefly :

  1. Write the scope of machine design.
  2. Write the sources of design data.
  3. Draw un-symmetric welded sections.
  4. Define pitch and lead.
  5. --- Content provided by FirstRanker.com ---

  6. What is the function of keys?
  7. Write different types of couplings.
  8. What are the main indications of a complete welding symbol?
  9. What are the factors to be considered for designing the fulcrum pin of the lever?
  10. What are the uses of foot lever?
  11. --- Content provided by FirstRanker.com ---

  12. Write types of friction clutches.

SECTION-B

  1. Why gibs are used in a cotter joint? Explain with the help of a neat sketch the use of single and double gib.
  2. Discuss the various types of shafts and the standard sizes of transmissions shafts.
  3. A square key of 10 x 10 x 75 mm is required to transmit 1100 N-m torque from a 60 m diameter solid shaft. Determine whether the length is sufficient or not if the permissible shear stress and crushing stress intensities limited to 60 and 170 MPa respectively.
  4. --- Content provided by FirstRanker.com ---

  5. State how a bolt of uniform strength is produced.
  6. Write short note on design of hand lever.

SECTION-C

  1. Discuss the design procedure while considering the economic, aesthetic and ergonomics aspect.
  2. Draw and explain the construction, working, application and design process of split muff coupling.
  3. --- Content provided by FirstRanker.com ---

  4. A vehicle of mass 1200 kg is moving down the hill at a slope of 1:5 at 72 km / h. It is to be stopped in a distance of 50 m. If the diameter of the tyre is 600 mm, determine the average braking torque to be applied to stop the vehicle, neglecting all the frictional energy except for the brake. If the friction energy is momentarily stored in a 20 kg cast iron brake drum, what is average temperature rise of the drum? The specific heat for cast iron may be taken as 520 J / kg°C. Determine also the minimum coefficient of friction between the tyres and the road in order that the wheels do not skid, assuming that the weight is equally distributed among all the four wheels.

NOTE : Disclosure of Identity by writing Mobile No. or Making of passing request on any page of Answer Sheet will lead to UMC against the Student.

FirstRanker.com


--- Content provided by FirstRanker.com ---


This download link is referred from the post: PTU B.Tech Question Papers 2020 December (All Branches)