Download JNTU Kakinada (Jawaharlal Nehru Technological University, Kakinada) M.Tech (Master of Technology) R13 Advanced Power Systems R13
COURSE STRUCTURE
AND
DETAILED SYLLABUS
For
M.Tech: EEE
Common Specializations:
I. POWER SYSTEMS
II. POWER SYSTEM CONTROL AND AUTOMATION
III. POWER SYSTEM ENGINEERING
IV. POWER SYSTEM AND CONTROL
V. ADVANCED POWER SYSTEMS
VI. ELECTRICAL POWER ENGINEERING
VII. POWER ENGINEERING & ENERGY SYSTEMS
JAWAHARLAL NEHRU TECHNOLOGY UNIVERSITY KAKINADA
KAKINADA - 533 003, Andhra Pradesh, India
PS
1
ACADEMIC REGULATIONS R13 FOR M. Tech (REGULAR)
DEGREE COURSE
Applicable for the students of M. Tech (Regular) Course from the
Academic Year 2013-14 onwards
The M. Tech Degree of Jawaharlal Nehru Technological University
Kakinada shall be conferred on candidates who are admitted to the program
and who fulfil all the requirements for the award of the Degree.
1.0 ELIGIBILITY FOR ADMISSIONS
Admission to the above program shall be made subject to eligibility,
qualification and specialization as prescribed by the University from time to
time.
Admissions shall be made on the basis of merit/rank obtained by the
candidates at the qualifying Entrance Test conducted by the University or
on the basis of any other order of merit as approved by the University,
subject to reservations as laid down by the Govt. from time to time.
2.0 AWARD OF M. Tech DEGREE
2.1
A student shall be declared eligible for the award of the M. Tech
Degree, if he pursues a course of study in not less than two and not
more than four academic years.
2.2
The student shall register for all 80 credits and secure all the 80 credits.
2.3
The minimum instruction days in each semester are 90.
3.0 A. COURSES OF STUDY
The following specializations are offered at present for the M. Tech
course of study.
1.
M.Tech- Structural Engineering
2.
M.Tech- Transportation Engineering
3.
M.Tech- Infrastructure Engineering & Management
4.
ME- Soil Mechanics and Foundation Engineering
5.
M.Tech- Environmental Engineering
6.
M.Tech-Geo-Informatics
7.
M.Tech-Spatial Information Technology
2
2013-14
8.
M.Tech- Civil Engineering
9.
M.Tech -Geo-Technical Engineering
10.
M.Tech- Remote Sensing
11.
M.Tech- Power Electronics
12.
M.Tech- Power & Industrial Drives
13.
M.Tech- Power Electronics & Electrical Drives
14.
M.Tech- Power System Control & Automation
15.
M.Tech- Power Electronics & Drives
16.
M.Tech- Power Systems
17.
M.Tech- Power Systems Engineering
18.
M.Tech- High Voltage Engineering
19.
M.Tech- Power Electronics and Power Systems
20.
M.Tech- Power System and Control
21.
M.Tech- Power Electronics & Systems
22.
M.Tech- Electrical Machines and Drives
23.
M.Tech- Advanced Power Systems
24.
M.Tech- Power Systems with Emphasis on High Voltage Engineering
25.
M.Tech- Control Engineering
26.
M.Tech- Control Systems
27.
M.Tech- Electrical Power Engineering
28.
M.Tech- Power Engineering & Energy System
29.
M.Tech- Thermal Engineering
30.
M.Tech- CAD/CAM
31.
M.Tech- Machine Design
32.
M.Tech- Computer Aided Design and Manufacture
33.
M.Tech- Advanced Manufacturing Systems
34.
M.Tech-Computer Aided Analysis & Design
35.
M.Tech- Mechanical Engineering Design
36.
M.Tech- Systems and Signal Processing
37.
M.Tech- Digital Electronics and Communication Systems
38.
M.Tech- Electronics & Communications Engineering
39.
M.Tech- Communication Systems
40.
M.Tech- Communication Engineering & Signal Processing
41.
M.Tech- Microwave and Communication Engineering
42.
M.Tech- Telematics
PS
3
43.
M.Tech- Digital Systems & Computer Electronics
44.
M.Tech- Embedded System
45.
M.Tech- VLSI
46.
M.Tech- VLSI Design
47.
M.Tech- VLSI System Design
48.
M.Tech- Embedded System & VLSI Design
49.
M.Tech- VLSI & Embedded System
50.
M.Tech- VLSI Design & Embedded Systems
51.
M.Tech- Image Processing
52.
M.Tech- Digital Image Processing
53.
M.Tech- Computers & Communication
54.
M.Tech- Computers & Communication Engineering
55.
M.Tech- Instrumentation & Control Systems
56.
M.Tech ? VLSI & Micro Electronics
57.
M.Tech ? Digital Electronics & Communication Engineering
58.
M.Tech- Embedded System & VLSI
59.
M.Tech- Computer Science & Engineering
60.
M.Tech- Computer Science
61.
M.Tech- Computer Science & Technology
62.
M.Tech- Computer Networks
63.
M.Tech- Computer Networks & Information Security
64.
M.Tech- Information Technology
65.
M.Tech- Software Engineering
66.
M.Tech- Neural Networks
67.
M.Tech- Chemical Engineering
68.
M.Tech- Biotechnology
69.
M.Tech- Nano Technology
70.
M.Tech- Food Processing
71.
M.Tech- Avionics
and any other course as approved by AICTE/ University from time to time.
4
2013-14
3.0 B.
Departments offering M. Tech Programmes with specializations
are noted below:
Civil Engg.
1.
M.Tech- Structural Engineering
2.
M.Tech- Transportation Engineering
3.
M.Tech- Infrastructure Engineering & Management
4.
ME- Soil Mechanics and Foundation Engineering
5.
M.Tech- Environmental Engineering
6.
M.Tech-Geo-Informatics
7.
M.Tech-Spatial Information Technology
8.
M.Tech- Civil Engineering
9.
M.Tech -Geo-Technical Engineering
10. M.Tech- Remote Sensing
E E E
1.
M.Tech- Power Electronics
2.
M.Tech- Power & Industrial Drives
3.
M.Tech- Power Electronics & Electrical Drives
4.
M.Tech- Power System Control & Automation
5.
M.Tech- Power Electronics & Drives
6.
M.Tech- Power Systems
7.
M.Tech- Power Systems Engineering
8.
M.Tech- High Voltage Engineering
9.
M.Tech- Power Electronics and Power Systems
10. M.Tech- Power System and Control
11. M.Tech- Power Electronics & Systems
12. M.Tech- Electrical Machines and Drives
13. M.Tech- Advanced Power Systems
14. M.Tech- Power Systems with Emphasis on High
Voltage Engineering
15. M.Tech- Control Engineering
16. M.Tech- Control Systems
17. M.Tech- Electrical Power Engineering
18. M.Tech- Power Engineering & Energy System
M E
1.
M.Tech- Thermal Engineering
2.
M.Tech- CAD/CAM
3.
M.Tech- Machine Design
4.
M.Tech- Computer Aided Design and Manufacture
5.
M.Tech- Advanced Manufacturing Systems
6.
M.Tech-Computer Aided Analysis & Design
7.
M.Tech- Mechanical Engineering Design
PS
5
E C E
1.
M.Tech- Systems and Signal Processing
2.
M.Tech- Digital Electronics and Communication
Systems
3.
M.Tech- Electronics & Communications Engineering
4.
M.Tech- Communication Systems
5.
M.Tech- Communication Engineering & Signal
Processing
6.
M.Tech- Microwave and Communication Engineering
7.
M.Tech- Telematics
8.
M.Tech- Digital Systems & Computer Electronics
9.
M.Tech- Embedded System
10. M.Tech- VLSI
11. M.Tech- VLSI Design
12. M.Tech- VLSI System Design
13. M.Tech- Embedded System & VLSI Design
14. M.Tech- VLSI & Embedded System
15. M.Tech- VLSI Design & Embedded Systems
16. M.Tech- Image Processing
17. M.Tech- Digital Image Processing
18. M.Tech- Computers & Communication
19. M.Tech- Computers & Communication Engineering
20. M.Tech- Instrumentation & Control Systems
21. M.Tech ? VLSI & Micro Electronics
22. M.Tech ? Digital Electronics & Communication
Engineering
23. M.Tech- Embedded System & VLSI
CSE
1.
M.Tech- Computer Science & Engineering
2.
M.Tech- Computer Science
3.
M.Tech- Computer Science & Technology
4.
M.Tech- Computer Networks
5.
M.Tech- Computer Networks & Information Security
6.
M.Tech- Information Technology
7.
M.Tech- Software Engineering
8.
M.Tech- Neural Networks
Others
1.
M.Tech- Chemical Engineering
2.
M.Tech- Biotechnology
3.
M.Tech- Nano Technology
4.
M.Tech- Food Processing
5.
M.Tech- Avionics
6
2013-14
4.0 ATTENDANCE
4.1
A student shall be eligible to write University examinations if he
acquires a minimum of 75% of attendance in aggregate of all the
subjects.
4.2
Condonation of shortage of attendance in aggregate up to 10%
(65% and above and below 75%) in each semester shall be
granted by the College Academic Committee.
4.3
Shortage of Attendance below 65% in aggregate shall not be
condoned.
4.4
Students whose shortage of attendance is not condoned in
any semester are not eligible to write their end semester
examination of that class.
4.5
A prescribed fee shall be payable towards condonation of
shortage of attendance.
4.6
A student shall not be promoted to the next semester unless he
satisfies the attendance requirement of the present semester, as
applicable. They may seek readmission into that semester when
offered next. If any candidate fulfills the attendance requirement
in the present semester, he shall not be eligible for readmission
into the same class.
5.0 EVALUATION
The performance of the candidate in each semester shall be evaluated
subject-wise, with a maximum of 100 marks for theory and 100 marks for
practicals, on the basis of Internal Evaluation and End Semester Examination.
5.1
For the theory subjects 60 marks shall be awarded based on the
performance in the End Semester Examination and 40 marks
shall be awarded based on the Internal Evaluation. The internal
evaluation shall be made based on the average of the marks
secured in the two Mid Term-Examinations conducted-one in
the middle of the Semester and the other immediately after the
completion of instruction. Each mid term examination shall be
conducted for a total duration of 120 minutes with 4 questions
(without choice) each question for 10 marks. End semester
examination is conducted for 60 marks for 5 questions to be
answered out of 8 questions.
PS
7
5.2
For practical subjects, 60 marks shall be awarded based on the
performance in the End Semester Examinations and 40 marks
shall be awarded based on the day-to-day performance as
Internal Marks.
5.3
There shall be two seminar presentations during III semester
and IV semester. For seminar, a student under the supervision
of a faculty member, shall collect the literature on a topic and
critically review the literature and submit it to the department in
a report form and shall make an oral presentation before the
Project Review Committee consisting of Head of the Department,
Supervisor and two other senior faculty members of the
department. For each Seminar there will be only internal
evaluation of 50 marks. A candidate has to secure a minimum of
50% of marks to be declared successful.
5.4
A candidate shall be deemed to have secured the minimum
academic requirement in a subject if he secures a minimum of
40% of marks in the End semester Examination and a minimum
aggregate of 50% of the total marks in the End Semester
Examination and Internal Evaluation taken together.
5.5
In case the candidate does not secure the minimum academic
requirement in any subject (as specified in 5.4) he has to reappear
for the End semester Examination in that subject. A candidate
shall be given one chance to re-register for each subject provided
the internal marks secured by a candidate are less than 50% and
has failed in the end examination. In such a case, the candidate
must re-register for the subject(s) and secure the required
minimum attendance. The candidate's attendance in the re-
registered subject(s) shall be calculated separately to decide
upon his eligibility for writing the end examination in those
subject(s). In the event of the student taking another chance,
his internal marks and end examination marks obtained in the
previous attempt stand cancelled. For re-registration the
candidates have to apply to the University through the college
by paying the requisite fees and get approval from the
University before the start of the semester in which re-
registration is required.
8
2013-14
5.6
In case the candidate secures less than the required attendance
in any re registered subject (s), he shall not be permitted to
write the End Examination in that subject. He shall again re-
register the subject when next offered.
5.7
Laboratory examination for M. Tech. courses must be conducted
with two Examiners, one of them being the Laboratory Class
Teacher or teacher of the respective college and the second
examiner shall be appointed by the university from the panel of
examiners submitted by the respective college.
6.0 EVALUATION OF PROJECT/DISSERTATION WORK
Every candidate shall be required to submit a thesis or dissertation
on a topic approved by the Project Review Committee.
6.1
A Project Review Committee (PRC) shall be constituted with
Head of the Department and two other senior faculty members.
6.2
Registration of Project Work: A candidate is permitted to register
for the project work after satisfying the attendance requirement
of all the subjects, both theory and practical.
6.3
After satisfying 6.2, a candidate has to submit, in consultation
with his project supervisor, the title, objective and plan of action
of his project work for approval. The student can initiate the
Project work, only after obtaining the approval from the Project
Review Committee (PRC).
6.4
If a candidate wishes to change his supervisor or topic of the
project, he can do so with the approval of the Project Review
Committee (PRC). However, the Project Review Committee (PRC)
shall examine whether or not the change of topic/supervisor
leads to a major change of his initial plans of project proposal.
If yes, his date of registration for the project work starts from
the date of change of Supervisor or topic as the case may be.
6.5
A candidate shall submit his status report in two stages at least
with a gap of 3 months between them.
6.6
The work on the project shall be initiated at the beginning of
the II year and the duration of the project is two semesters. A
candidate is permitted to submit Project Thesis only after
PS
9
successful completion of theory and practical course with the
approval of PRC not earlier than 40 weeks from the date of
registration of the project work. The candidate has to pass all
the theory and practical subjects before submission of the
Thesis.
6.7
Three copies of the Project Thesis certified by the supervisor
shall be submitted to the College/School/Institute.
6.8
The thesis shall be adjudicated by one examiner selected by the
University. For this, the Principal of the College shall submit a
panel of 5 examiners, eminent in that field, with the help of the
guide concerned and head of the department.
6.9
If the report of the examiner is not favourable, the candidate
shall revise and resubmit the Thesis, in the time frame as decided
by the PRC. If the report of the examiner is unfavorable again,
the thesis shall be summarily rejected. The candidate has to re-
register for the project and complete the project within the
stipulated time after taking the approval from the University.
6.10 If the report of the examiner is favourable, Viva-Voce examination
shall be conducted by a board consisting of the Supervisor,
Head of the Department and the examiner who adjudicated the
Thesis. The Board shall jointly report the candidate's work as
one of the following:
A.
Excellent
B.
Good
C.
Satisfactory
D.
Unsatisfactory
The Head of the Department shall coordinate and make arrangements
for the conduct of Viva-Voce examination.
6.11 If the report of the Viva-Voce is unsatisfactory, the candidate
shall retake the Viva-Voce examination only after three months.
If he fails to get a satisfactory report at the second Viva-Voce
examination, the candidate has to re-register for the project and
complete the project within the stipulated time after taking the
approval from the University.
10
2013-14
7.0 AWARD OF DEGREE AND CLASS
After a student has satisfied the requirements prescribed for the
completion of the program and is eligible for the award of M. Tech. Degree
he shall be placed in one of the following four classes:
Class Awarded
% of marks to be secured
First Class with Distinction
70% and above (Without any
Supplementary Appearance )
First Class
Below 70% but not less than 60%
70% and above (With any
Supplementary Appearance )
Second Class
Below 60% but not less than 50%
The marks in internal evaluation and end examination shall be shown
separately in the memorandum of marks.
8.0 WITHHOLDING OF RESULTS
If the student has not paid the dues, if any, to the university or if any
case of indiscipline is pending against him, the result of the student will be
withheld. His degree will be withheld in such cases.
4.0 TRANSITORY REGULATIONS ( for R09 )
9.1
Discontinued or detained candidates are eligible for re-
admission into same or equivalent subjects at a time as and
when offered.
9.2
The candidate who fails in any subject will be given two
chances to pass the same subject; otherwise, he has to identify
an equivalent subject as per R13 academic regulations.
10. GENERAL
10.1 Wherever the words "he", "him", "his", occur in the
regulations, they include "she", "her", "hers".
10.2 The academic regulation should be read as a whole for the
purpose of any interpretation.
10.3 In the case of any doubt or ambiguity in the interpretation of
the above rules, the decision of the Vice-Chancellor is final.
10.4 The University may change or amend the academic regulations
or syllabi at any time and the changes or amendments made
shall be applicable to all the students with effect from the
dates notified by the University.
PS
11
MALPRACTICES RULES
DISCIPLINARY ACTION FOR / IMPROPER CONDUCT IN
EXAMINATIONS
Nature of Malpractices/
Punishment
Improper conduct
If the candidate:
1. (a) Possesses or keeps accessible Expulsion from the examination hall
in examination hall, any paper, and cancellation of the
note book, programmable performance in that subject only.
calculators, Cell phones, pager,
palm computers or any other
form of material concerned
with or related to the subject
of the examination (theory or
practical) in which he is
appearing but has not made
use of (material shall include
any marks on the body of the
candidate which can be used
as an aid in the subject of the
examination)
(b)
Gives assistance or guidance Expulsion from the examination hall
or receives it from any other and cancellation of the
candidate orally or by any performance in that subject only of
other body language methods all the candidates involved. In case
or communicates through cell of an outsider, he will be handed
phones with any candidate or over to the police and a case is
persons in or outside the exam registered against him.
hall in respect of any matter.
2.
Has copied in the examination Expulsion from the examination hall
hall from any paper, book, and cancellation of the
programmable calculators, performance in that subject and all
palm computers or any other other subjects the candidate has
form of material relevant to the already appeared including
subject of the examination practical examinations and project
12
2013-14
(theory or practical) in which work and shall not be permitted to
the candidate is appearing.
appear for the remaining
examinations of the subjects of that
Semester/year. The Hall Ticket of
the candidate is to be cancelled
and sent to the University.
3.
Impersonates any other The candidate who has
candidate in connection with impersonated shall be expelled from
the examination.
examination hall. The candidate is
also debarred and forfeits the seat.
The performance of the original
candidate who has been
impersonated, shall be cancelled in
all the subjects of the examination
(including practicals and project
work) already appeared and shall
not be allowed to appear for
examinations of the remaining
subjects of that semester/year. The
candidate is also debarred for two
consecutive semesters from class
work and all University
examinations. The continuation of
the course by the candidate is
subject to the academic regulations
in connection with forfeiture of
seat. If the imposter is an outsider,
he will be handed over to the police
and a case is registered against him.
4.
Smuggles in the Answer book Expulsion from the examination hall
or additional sheet or takes out and cancellation of performance in
or arranges to send out the that subject and all the other
question paper during the subjects the candidate has already
examination or answer book or appeared including practical
additional sheet, during or after examinations and project work and
PS
13
the examination.
shall not be permitted for the
remaining examinations of the
subjects of that semester/year. The
candidate is also debarred for two
consecutive semesters from class
work and all University
examinations. The continuation of
the course by the candidate is
subject to the academic regulations
in connection with forfeiture of seat.
5.
Uses objectionable, abusive or Cancellation of the performance in
offensive language in the that subject.
answer paper or in letters to the
examiners or writes to the
examiner requesting him to
award pass marks.
6.
Refuses to obey the orders of In case of students of the college,
the Chief Superintendent/ they shall be expelled from
Assistant ? Superintendent / examination halls and cancellation of
any officer on duty or their performance in that subject and
misbehaves or creates all other subjects the candidate(s)
disturbance of any kind in and has (have) already appeared and
around the examination hall or shall not be permitted to appear for
organizes a walk out or the remaining examinations of the
instigates others to walk out, subjects of that semester/year. The
or threatens the officer-in candidates also are debarred and
charge or any person on duty forfeit their seats. In case of
in or outside the examination outsiders, they will be handed over
hall of any injury to his person to the police and a police case is
or to any of his relations registered against them.
whether by words, either
spoken or written or by signs
or by visible representation,
assaults the officer-in-charge,
or any person on duty in or
14
2013-14
outside the examination hall or
any of his relations, or
indulges in any other act of
misconduct or mischief which
result in damage to or
destruction of property in the
examination hall or any part of
the College campus or
engages in any other act which
in the opinion of the officer on
duty amounts to use of unfair
means or misconduct or has
the tendency to disrupt the
orderly conduct of the
examination.
7.
Leaves the exam hall taking Expulsion from the examination hall
away answer script or and cancellation of performance in
intentionally tears of the script that subject and all the other
or any part thereof inside or subjects the candidate has already
outside the examination hall. appeared including practical
examinations and project work and
shall not be permitted for the
remaining examinations of the
subjects of that semester/year. The
candidate is also debarred for two
consecutive semesters from class
work and all University
examinations. The continuation of
the course by the candidate is
subject to the academic regulations
in connection with forfeiture of seat.
8.
Possess any lethal weapon or Expulsion from the examination hall
firearm in the examination hall. and cancellation of the performance
in that subject and all other subjects
the candidate has already appeared
including practical examinations
and project work and shall not be
permitted for the remaining
PS
15
examinations of the subjects of that
semester/year. The candidate is
also debarred and forfeits the seat.
9.
If student of the college, who Student of the colleges expulsion
is not a candidate for the from the examination hall and
particular examination or any cancellation of the performance in
person not connected with the that subject and all other subjects
college indulges in any the candidate has already appeared
malpractice or improper including practical examinations
conduct mentioned in clause 6 and project work and shall not be
to 8.
permitted for the remaining
examinations of the subjects of that
semester/year. The candidate is also
debarred and forfeits the seat.
Person(s) who do not belong to the
College will be handed over to police
and, a police case will be registered
against them.
10.
Comes in a drunken condition Expulsion from the examination hall
to the examination hall.
and cancellation of the
performance in that subject and all
other subjects the candidate has
already appeared including
practical examinations and project
work and shall not be permitted for
the remaining examinations of the
subjects of that semester/year.
11.
Copying detected on the basis Cancellation of the performance in
of internal evidence, such as, that subject and all other subjects
during valuation or during the candidate has appeared
special scrutiny.
including practical examinations
and project work of that semester/
year examinations.
12.
If any malpractice is detected
which is not covered in the
above clauses 1 to 11 shall be
reported to the University for further action
to award suitable punishment.
16
2013-14
Malpractices identified by squad or special invigilators
1.
Punishments to the candidates as per the above guidelines.
2.
Punishment for institutions : (if the squad reports that the college is
also involved in encouraging malpractices)
(i)
A show cause notice shall be issued to the college.
(ii)
Impose a suitable fine on the college.
(iii)
Shifting the examination centre from the college to another
college for a specific period of not less than one year.
PS
17
JAWAHARLAL NEHRU TECHNOLOGICAL
UNIVERSITY: KAKINADA
KAKINADA-533003, Andhra Pradesh (India)
For Constituent Colleges and Affiliated Colleges of JNTUK
Ragging
Prohibition of ragging in educational institutions Act 26 of 1997
Salient Features
Ragging within or outside any educational institution is prohibited.
Ragging means doing an act which causes or is likely to cause Insult
or Annoyance of Fear or Apprehension or Threat or Intimidation or
outrage of modesty or Injury to a student
Imprisonment upto
Fine Upto
Teasing,
Embarrassing and
6 Months
+
Rs. 1,000/-
Humiliation
Assaulting or
Using Criminal
1 Year
+
Rs. 2,000/-
force or Criminal
intimidation
Wrongfully
restraining or
2 Years
+
Rs. 5,000/-
confining or
causing hurt
Causing grievous
hurt, kidnapping
or Abducts or rape
5 Years
+
Rs.10,000/-
or committing
unnatural offence
Causing death or
10 Months
+
Rs. 50,000/-
abetting suicide
In Case of Emergency CALL TOLL FREE NO. : 1800 - 425 - 1288
LET US MAKE JNTUK A RAGGING FREE UNIVERSITY
18
2013-14
JAWAHARLAL NEHRU TECHNOLOGICAL
UNIVERSITY: KAKINADA
KAKINADA-533003, Andhra Pradesh (India)
For Constituent Colleges and Affiliated Colleges of JNTUK
Ragging
ABSOLUTELY
NO TO RAGGING
1.
Ragging is prohibited as per Act 26 of A.P. Legislative Assembly,
1997.
2.
Ragging entails heavy fines and/or imprisonment.
3.
Ragging invokes suspension and dismissal from the College.
4.
Outsiders are prohibited from entering the College and Hostel without
permission.
5.
Girl students must be in their hostel rooms by 7.00 p.m.
6.
All the students must carry their Identity Card and show them when
demanded
7.
The Principal and the Wardens may visit the Hostels and inspect the
rooms any time.
Jawaharlal Nehru Technological University Kakinada
For Constituent Colleges and Affiliated Colleges of JNTUK
In Case of Emergency CALL TOLL FREE NO. : 1800 - 425 - 1288
LET US MAKE JNTUK A RAGGING FREE UNIVERSITY
PS
19
COURSE STRUCTURE
I SEMESTER
S.No Name of the Subject
L
P
C
1
Microprocessors & Microcontrollers
4
--
3
2
HVDC Transmission
4
--
3
3
Power System Operation and Control
4
--
3
4
Reactive Power Compensation & Management
4
--
3
5
Elective ? I
4
--
3
Electrical Distribution Systems
HVAC Transmission
Analysis of Power Electronics Converters
Renewable Energy Systems
Artificial Intelligence Techniques
6
Elective ? II
4
--
3
Power System Security
Advanced Digital Signal Processing
Generation & Measurement of High Voltages
Programmable Logic Controllers & Applications
Modern Control Theory
7
Simulation Laboratory
--
4
2
Total
20
II SEMESTER
1
Power System Dynamics and Stability
4
--
3
2
Flexible AC Transmission Systems
4
--
3
3
Real Time Control of Power Systems
4
--
3
4
Advanced Power System Protection
4
--
3
5
Elective ? III
4
--
3
Smart Grid
Power Quality
Power System Reliability
Voltage Stability
6
Elective ? IV
4
--
3
Power System Deregulation
High Voltage Testing Techniques
20
2013-14
Power System Transients
Demand Side Energy Management
7
Power Systems Laboratory
--
4
2
Total
20
III SEMESTER
1
Seminar ? I
--
--
2
2
Project Work - I
--
--
18
Total
20
IV SEMESTER
1
Seminar ? II
--
--
2
2
Project Work - II
--
--
18
Total
20
PS
21
SYLLABUS
I ? I
L
P
Credits
4
-
3
MICROPROCESSORS & MICRO CONTROLLERS
UNIT-I
Register Organization of 8086, Architecture, Signal description of 8086,
memory segmentation, addressing modes of 8086. 8086/8088 instruction
set and assembler directives, machine language instruction formats,
Assembly language Programs.
UNIT-II
General Bus Operation, minimum mode operation of 8086 and timing
diagrams, Fundamental I/O considerations, Programmed I/O, Interrupt
I/O, Block transfers and DMA.
UNIT-III
Introduction to stack, stack structure of 8086/8088, Interrupts and
Interrupt service routine, interrupt cycle of 8086/8088. Interfacing ROM/
RAM, Interfacing of I/O ports to Micro Computer System, PPI
(Programmable Peripheral Interface), 8255 modes of operation,
Interfacing A to D converters, Interfacing D to A converters, Interfacing
Principles and stepper motor interfacing.
UNIT-IV
Programmable Interval timer 8254, Programmable Interrupt Controller
8259A, Key Board or Display Controller 8279, Programmable
Communication Interface 8251 USART.
UNIT-V
Introduction to 8051/31 Micro Controller, PIN diagram, architecture,
Different modes of Operation of timer/counters, addressing modes of
8051 and instruction set. Over view of 16 bit Microcontrollers.
REFERENCE BOOKS:
1.
Microprocessors and Interfacing: Programming and Hardware by
Douglas V. Hall, 2nd edition, TMH, New Delhi, 1999.
22
2013-14
2.
Advanced Microprocessors and Peripherals, Architecture Programming
and Interfacing by A.K. Ray & K.M. Bhurchandi, Forth reprint 2004,
TMH
3.
The 8051Microcontrollers: Architecture, Programming & Applications
by Kenneth J Ayala, Second Edition, Penram International Publishing
(India).
4.
Micro Computer Systems: The 8086/8088 family by YU-CHENG LIU,
GLENN A.GIBSON, 2nd edition, PHI India, 2000.
5.
The 8051 Microcontroller and Embedded Systems ? Mohammad Ali
Mazdi, Janice Gillispie Mazidi, Pearson Education (Singapore) Pvt. Ltd.,
2003.
PS
23
I ? I
L
P
Credits
4
-
3
H.V.D.C. TRANSMISSION
UNIT- I
Limitation of EHV AC Transmission .Advantages of HVDC Technical
economical reliability aspects. H.V.D.C. Transmission: General
considerations, Power Handling Capabilities of HVDC Lines, Basic
Conversion principles, static converter configuration. Types of HVDC
links-Apparatus and its purpose.
UNIT II:
Static Power Converters: 6-pulse bridge circuit and 12-pulse converters,
converter station and Terminal equipment, commutation process,
Rectifier and inverter operation, equivalent circuit for converter ? special
features of converter transformers. Comparison of the perform of
diametrical connection with 6-pulse bridge circuit
UNIT- III
Control of HVDC Converters and systems: constant current, constant
extinction angle and constant Ignition angle control. Individual phase
control and equidistant firing angle control, DC power flow control.
Factors responsible for generation of Harmonics voltage and current
harmonics effect of variation of ? and . Filters Harmonic elimination.
UNIT-IV
Interaction between HV AC and DC systems ? Voltage interaction,
Harmonic instability problems and DC power modulation. Development
of DC circuit Breakers, Multi-terminal DC links and systems; series,
parallel and series parallel systems, their operation and control.
UNIT- V
Transient over voltages in HV DC systems : Over voltages due to
disturbances on DC side, over voltages due to DC and AC side line
faults. Converter faults and protection in HVDC Systems: Converter
faults, over current protection - valve group, and DC line protection,
circuit breakers. Over voltage protection of converters, surge arresters.
24
2013-14
REFERENCE BOOKS :
1.
K.R.Padiyar : High Voltage Direct current Transmission, Wiley Eastern
Ltd., New Delhi ? 1992.
2.
E.W. Kimbark : Direct current Transmission, Wiley Inter Science ? New
York.
3.
J.Arillaga : H.V.D.C.Transmission Peter Peregrinus ltd., London UK
1983
4.
E.Uhlman : Power Transmission by Direct Current, Springer Verlag,
Berlin Helberg ? 1985.
5.
HVDC Transmission-S Kamakshaih and V Kamaraju MG hill.
PS
25
I ? I
L
P
Credits
4
-
3
POWER SYSTEM OPERATION AND CONTROL
UNIT-I
Unit commitment problem and optimal power flow solution : Unit
commitment : Constraints in UCP,UC solutions. Methods-priority list
method, introduction to Dynamic programming Approach.
UNIT-II
Load Frequency Control-I : Necessity of keeping frequency constant.
Definition of control area, single area control, Block diagram
representation of an isolated Power System, Steady State analysis,
Dynamic response-Uncontrolled case. Proportional plus Integral
control of single area and its block diagram representation, steady
state response, load frequency control and Economic dispatch control.
UNIT-III
Load Frequency Control-II : Load frequency control of 2-area system
: uncontrolled case and controlled case, tie-line bias control. Optimal
two-area LF control-steady state representation, performance Index
and optimal parameter adjustment.
UNIT-IV
Generation with limited Energy supply : Take-or-pay fuel supply
contract, composite generation production cost function. Solution by
gradient search techniques, Hard limits and slack variables, Fuel
scheduling by linear programming.
UNIT-V
Interchange Evaluation and Power Pools Economy Interchange,
Economy interchange Evaluation, Interchange Evaluation with unit
commitment, Multiple Interchange contracts. After-the-fact production
costing, Transmission Losses in transaction Evaluation, other types
of Interchange, power pools.
26
2013-14
REFERENCE BOOKS :
1
Modern Power System Analysis - by I.J.Nagrath & D.P.Kothari, Tata
Mc Graw-Hill Publishing Company ltd, 2nd edition.
2
Power system operation and control PSR Murthy B.S publication.
3
Power Generation, Operation and Control - by A.J.Wood and
B.F.Wollenberg,John wiley & sons Inc. 1984.
4
Electrical Energy Systems Theory - by O.I.Elgerd, Tata Mc Graw-Hill
Publishing Company Ltd, 2nd edition.
5
Reactive Power Control in Electric Systems - by TJE Miller, John Wiley
& sons.
PS
27
I ? I
L
P
Credits
4
-
3
REACTIVE POWER COMPENSATION &
MANAGEMENT
UNIT-I
Load Compensation Objectives and specifications ? reactive power
characteristics ? inductive and capacitive approximate biasing ? Load
compensator as a voltage regulator ? phase balancing and power factor
correction of unsymmetrical loads- examples.
UNIT- II
Reactive power compensation in transmission system: Steady state -
Uncompensated line ? types of compensation ? Passive shunt and
series and dynamic shunt compensation ? examples
Transient state - Characteristic time periods ? passive shunt
compensation ? static compensations- series capacitor compensation
?compensation using synchronous condensers ? examples
UNIT-III
Reactive power coordination: Objective ? Mathematical modeling ?
Operation planning ? transmission benefits ? Basic concepts of quality
of power supply ? disturbances- steady ?state variations ? effects of
under voltages ? frequency ? Harmonics, radio frequency and
electromagnetic interferences
UNIT-IV
Distribution side Reactive power Management: System losses ?loss
reduction methods ? examples ? Reactive power planning ? objectives
? Economics Planning capacitor placement ? retrofitting of capacitor
banks
User side reactive power management: KVAR requirements for domestic
appliances ? Purpose of using capacitors ? selection of capacitors ?
deciding factors ? types of available capacitor, characteristics and
Limitations
28
2013-14
UNIT-V
Reactive power management in electric traction systems and are
furnaces: Typical layout of traction systems ? reactive power control
requirements ? distribution transformers- Electric arc furnaces ? basic
operations- furnaces transformer ?filter requirements ? remedial
measures ?power factor of an arc furnace
REFERENCE BOOKS:
1.
Reactive power control in Electric power systems by T.J.E.Miller, John
Wiley and sons, 1982
2.
Reactive power Management by D.M.Tagare,Tata McGraw Hill,2004
PS
29
I ? I
L
P
Credits
4
-
3
(ELECTIVE-I)
ELECTRICAL DISTRIBUTION SYSTEMS
UNIT- I
General : Introduction to Distribution systems, an overview of the
role of computers in distribution system planning-Load modeling and
characteristics: definition of basic terms like demand factor, utilization
factor, load factor, plant factor, diversity factor, coincidence factor,
contribution factor and loss factor-Relationship between the load
factor and loss factor - Classification of loads (Residential,
Commercial, Agricultural and Industrial) and their characteristics.
UNIT-II
Distribution Feeders and Substations : Design consideration of
Distribution feeders: Radial and loop types of primary feeders, voltage
levels, feeder-loading. Design practice of the secondary distribution
system. Location of Substations : Rating of a Distribution Substation,
service area with primary feeders. Benefits derived through optimal
location of substations.
UNIT -III
System analysis : Voltage drop and power loss calculations : Derivation
for volt-drop and power loss in lines, manual methods of solution for
radial networks, three-phase balanced primary lines, non-three-phase
primary lines.
UNIT- IV
Protective devices and coordination : Objectives of distribution system
protection, types of common faults and procedure for fault calculation.
Protective Devices: Principle of operation of fuses, circuit reclosers,
line sectionalizer and circuit breakers. Coordination of protective devices
General coordination procedure.
UNIT -V
Capacitive compensation for power factor control: Different types of
power capacitors, shunt and series capacitors, effect of shunt capacitors
30
2013-14
(Fixed and switched ) power factor correction, capacitor location.
Economic justification. Procedure to determine the best capacitor
location. Voltage control : Equipment for voltage control, effect of series
capacitors, effect of AVB/AVR, line drop compensation.
REFERENCE BOOKS :
1.
"Electric Power Distribution System Engineering " by Turan Gonen,
Mc.Graw-Hill Book Company,1986.
2.
Electric Power Distribution-by A.S.Pabla, Tata Mc Graw-Hill Publishing
Company, 4th edition, 1997.
3.
Electrical Distribution V.Kamaraju-Mc Graw Hill
4.
Handbook of Electrical Power Distribution ? Gorti Ramamurthy-
Universities press.
PS
31
I ? I
L
P
Credits
4
-
3
(ELECTIVE-I)
HVAC TRANSMISSION
UNIT-I
E.H.V. A.C. Transmission , line trends and preliminary aspects ,standard
transmission voltages ? power handling capacities and line losses ?
mechanical aspects. Calculation of line resistance and inductance :
resistance of conductors, temperature rise of conductor and current
carrying capacity. Properties of bundled conductors and geometric
mean radius of bundle, inductance of two conductor lines and multi
conductor lines, Maxwell's coefficient matrix. Line capacitance
calculation : capacitance of two conductor line, and capacitance of
multi conductor lines, potential coefficients for bundled conductor
lines, sequence inductances and capacitances and diagonalization.
UNIT -II
Calculation of electro static field of AC lines - Effect of high electrostatic
field on biological organisms and human beings. Surface voltage
Gradient on conductors, surface gradient on two conductor bundle
and cosine law, maximum surface voltage gradient of bundle with more
than 3 sub conductors, Mangolt formula.
UNIT-III
Corona : Corona in EHV lines ? corona loss formulae ? attenuation of
traveling waves due to corona ? Audio noise due to corona, its
generation, characteristics and limits, measurement of audio noise.
UNIT-IV
Power Frequency voltage control : Problems at power frequency,
generalized constants, No load voltage conditions and charging
currents, voltage control using synchronous condenser, cascade
connection of components : Shunt and series compensation, sub
synchronous resonance in series ? capacitor compensated lines
32
2013-14
UNIT ?V
Static reactive compensating systems : Introduction, SVC schemes,
Harmonics injected into network by TCR, design of filters for
suppressing harmonics injected into the system.
REFERENCE BOOKS :
1.
Extra High Voltage AC Transmission Engineering ? Rakesh Das
Begamudre, Wiley Eastern ltd., New Delhi ? 1987.
2.
EHV Transmission line reference book ? Edison Electric Institute (GEC)
1986.
PS
33
I ? I
L
P
Credits
4
-
3
(ELECTIVE-I)
ANALYSIS OF POWER ELECTRONIC CONVERTERS
UNIT-I
AC voltage Controllers Single Phase AC Voltage Controllers with RL
and RLE loads-ac voltage controller's with PWM control-Effects of
source and load inductances ?synchronous tap changers ?Application-
numerical problems
Three Phase AC Voltage controllers-Analysis of Controllers with star
and delta connected resistive, resistive ?inductive loads-Effects of
source and load inductances?Application- numerical problems.
UNIT ?II
ac-dc converters Single phase Half controlled and Fully controlled
Converters with RL load? Evaluation of input power factor and harmonic
factor-Continuous and Discontinuous load current-Power factor
improvements-Extinction angle control-symmetrical angle control-
PWM single phase sinusoidal PWM-Single phase series converters-
numerical problems. Three Phase ac-dc Converters- Half controlled
and fully controlled Converters with RL load? Evaluation of input
power factor and harmonic factor-Continuous and Discontinuous load
current-three phase dual converters-Power factor improvements-three
phase PWM-twelve pulse converters- numerical problems
UNIT-III
Power Factor Correction Converters Single-phase single stage boost
power factor corrected rectifier, power circuit principle of operation,
and steady state- analysis, three phase boost PFC converter
UNIT ?IV
PWM Inverters Principle of operation-Voltage control of single phase
inverters - sinusoidal PWM ? modified PWM ? phase displacement
Control ? Trapezoidal, staircase, stepped, harmonic injection and delta
modulation ? numerical problems. Voltage Control of Three-Phase
Inverters- Sinusoidal PWM- 600 PWM- Third Harmonic PWM- Space
34
2013-14
Vector Modulation- Comparison of PWM Techniques-current source
inverters-Variable dc link inverter - numerical problems
UNIT- V
Multi level inverters Introduction, Multilevel Concept, Types of
Multilevel Inverters- Diode-Clamped Multilevel Inverter, Principle of
Operation, Features of Diode-Clamped Inverter, Improved Diode-
Clamped Inverter- Flying-Capacitors Multilevel Inverter- Principle of
Operation, Features of Flying-Capacitors Inverter- Cascaded Multilevel
Inverter- Principle of Operation- Features of Cascaded Inverter-
Switching Device Currents-DC-Link Capacitor Voltage Balancing-
Features of Multilevel Inverters- Comparisons of Multilevel Converters
TEXTBOOKS
1.
Power Electronics-Md.H.Rashid ?Pearson Education Third Edition-
First Indian Reprint- 2008
2.
Power Electronics- Ned Mohan, Tore M.Undelan and William P.Robbins
?John Wiley & Sons -2nd Edition.
3.
Power Electronics ? Lander ?Ed.2009
4.
Modern power Electronics and AC Drives ? B.K.Bose
5.
Power Converter Circuits ? William Shepherd & Li Zhang-Yes Dee
Publishing Pvt Ltd.
PS
35
I ? I
L
P
Credits
4
-
3
(ELECTIVE-I)
RENEWABLE ENERGY SYSTEMS
UNIT-I
Solar Energy - Availability - Solar radiation data and measurement -
Estimation of average solar radiation - Solar water heater types - Heat
balance ? Flat plate collector efficiency ? Efficiency of heat removal -
Thermo siphon flow calculation - Forced circulation calculation -
Evacuated collectors - Basics of solar concentrators Solar Energy
Applications - Solar air heaters ? Solar Chimney - Crop driers - Passive
solar system - Active solar systems - Water desalination - Output from
solar still ? Principle of solar ponds.
UNIT-II
Wind Energy ? Nature of wind ? Characteristics ? Variation with height
and time ? Power in wind ?Aerodynamics of Wind turbine ? Momentum
theory ? Basics of aerodynamics ? Aero foils and their characteristics
? HAWT ? Blade element theory ? Prandtl's lifting line theory
(prescribed wake analysis) VAWT aerodynamics ? Wind turbine loads
? Aerodynamic loads in steady operation ? Yawed operation and tower
shadow. Wind Energy Conversion System ? Siting ? Rotor selection ?
Annual energy output ? Horizontal axis wind turbine (HAWT) ? Vertical
axis wind turbine (VAWT) ? Rotor design considerations ? Number of
blades ? Solidity - Blade profile ? Upwind/Downwind ? Yaw system ?
Tower ? Braking system - Synchronous and asynchronous generators
and loads ? Integration of wind energy converters to electrical
networks ? Inverters ? Control system ? Requirement and strategies ?
Noise Applications of wind energy
UNIT-III
Biomass energy - Bio fuel classification ? Examples of thermo chemical,
Pyrolysis, biochemical and agrochemical systems ? Energy farming ?
Direct combustion for heat ? Process heat and electricity ? Ethanol
production and use ? Anaerobic digestion for biogas ? Different
digesters ? Digester sizing ? Applications of Biogas - Operation with
I.C.Engine
36
2013-14
UNIT-IV
Ocean Energy - OTEC Principle - Lambert's law of absorption - Open
cycle and closed cycle - heat exchanger calculations ? Major problems
and operational experience. Tidal Power - Principles of power
generation - components of power plant ? Single and two basin systems
? Turbines for tidal power - Estimation of energy ? Maximum and
minimum power ranges - tidal powerhouse.
Wave Energy ? Concept of energy and power from waves ? Wave
characteristics ? period and wave velocities - Different wave energy
conservation devices (Saltor duck, oscillating water column and dolphin
types) ? operational experience.
UNIT-V
Geothermal Energy - Classification- Fundamentals of geophysics - Dry
rock and hot aquifier energy analysis - Estimation of thermal power -
Extraction techniques - Prime movers.
REFERENCES:
1.
Renewable Energy Resources / John Twidell and Tony Weir / E &
F.N.Spon
2.
Renewable Energy Resources Basic Principles and Applications /
G.N.Tiwari and M.K.Ghosal / Narosa
3.
Solar Energy - Principles of thermal collection and storage/ S.P.
Sukhatme / TMH
4.
Solar Energy Thermal Processes,/Duffie & Beckman
5.
Solar Heating and Cooling / Kreith & Kreider
6.
Wind Energy Handbook / Tony Burton, David Sharpe, Nick Jenkins
and Ervin Bossanyi / WileyWind Electrical Systems / S.N.Bhadra,
D.Kastha and S.Banerjee / Oxford
7.
Biogas Technology - A Practical Hand Book / K.Khendelwal & S.S.
Mahdi / McGraw-Hill
PS
37
I ? I
L
P
Credits
-
4
2
(ELECTIVE-I)
ARTIFICIAL INTELLIGENCE TECHNIQUES
UNIT ? I
Introduction to Neural Networks Introduction, Humans and
Computers, Biological Neural Networks, Historical development of
neural network, Terminology and Topology, Biological and artificial
neuron models, Basic learning laws.
UNIT- II
Feed Forward Neural Networks Introduction, Perceptron models:
Discrete, continuous and multi-category, Training algorithms: Discrete
and Continuous Perceptron Networks, Perceptron convergence
theorem, Limitations and applications of the Perceptron model,
Generalized delta learning rule, Feedforward recall and error back
propagation training-Radial basis function algorithms-Hope field
networks
UNIT -III
Genetic algorithms & Modelling-introduction-encoding-fitness
function-reproduction operators-genetic operators-cross over and
mutation-generational cycle-convergence of genetic algorithm
UNIT ?IV
Classical and Fuzzy Sets Introduction to classical sets - properties,
operations and relations; Fuzzy sets, membership, Uncertainty,
operations, properties, fuzzy relations, cardinalities, membership
functions.
Fuzzy Logic System Components-Fuzzification, Membership value
assignment, development of rule base and decision making system,
defuzzification to crisp sets, defuzzification methods.
UNIT -V
APPLICATION OF AI TECHNIQUES-load forecasting-load flow
studies-economic load dispatch-load frequency control-reactive power
control-speed control of dc and ac motors
TEXT BOOK:
1.
Neural Networks, Fuzzy logic, Genetic algorithms: synthesis and
applications by Rajasekharan and Rai ? PHI yPublication.
2.
Introduction to Artificial Neural Systems - Jacek M. Zuarda, Jaico
Publishing House, 1997.
38
2013-14
I ? II
L
P
Credits
4
-
3
(ELECTIVE II)
POWER SYSTEM SECURITY
UNIT-I
Short circuit analysis techniques in AC power Systems- Simulation of
short circuit and open circuit faults using network theorems- fixed
impedance short circuit analysis techniques-time domain short circuit
analysis in large scale power systems- analysis of time variation of AC
and DC short circuit components
UNIT-II
Fixed impedance Short circuit analysis of large scale power systems-
general analysis of balanced, unbalanced and open circuit faults- 3-
phase short circuit analysis in large scale power systems, Network
equivalents and practical short circuit current assessments in large
scale Ac power systems-general studies- uncertainties in short circuit
current calculations-probabilistic Short circuit analysis
UNIT-III
Risk assessment and safety considerations-control and limitation of
high short circuit currents-limitation of short circuit currents in power
system operation, design and planning, Types of short circuit fault
current limiters- earthing resistor or reactor connected to transformer
neutral-pyrotechnic fault current limiters- series resonant current
limiters- saturable reactor limiters-other types of fault current limiters
and their applications.
UNIT-IV
Power System Security analysis- concept of security- security analysis
and monitoring- factors affecting power system security- detection of
network problems ?overview, contingency analysis for generator and
line outages by ILPF method ? fast decoupled inverse Lemma-based
approach, network sensitivity factors ?contingency selection ?
concentric relaxation and bounding.
PS
39
UNIT-V
Computer control power systems ? need for real time and computer
control of power systems- operating states of power system ? SCADA-
implementation considerations ? software requirements for
implementing above functions.
REFERENCE BOOKS:
1.
Allen J. Wood and Bruce Woolenberg: Power System Generation,
Operation and Control ,John Willey and sons,1996
2.
John J.Grainger and William D Stevenson Jr.: Power System
analysis,McGraw Hill,ISE,1994.
3.
Nasser D.Tleis : Power System Modelling and fault analysis, Elsevier,
2008.
40
2013-14
I ? II
L
P
Credits
4
-
3
(ELECTIVE II)
ADVANCED DIGITAL SIGNAL PROCESSING
UNIT-I
Digital Filter Structure Block diagram representation-Equivalent
Structures-FIR and IIR digital filter Structures All pass Filters-tunable
IIR Digital Filters-IIR tapped cascaded Lattice Structures-FIR cascaded
Lattice structures-Parallel-Digital Sine-cosine generator-Computational
complexity of digital filter structures.
UNIT-II
Digital filter design Preliminary considerations-Bilinear transformation
method of IIR filter design-design of Low pass high pass-Band pass,
and Band stop- IIR digital filters-Spectral transformations of IIR filters,
FIR filter design-based on Windowed Fourier series- design of FIR
digital filters with least ?mean- Square-error-constrained Least-square
design of FIR digital filters
UNIT-III
DSP algorithm implementation Computation of the discrete Fourier
transform- Number representation-Arithmetic operations-handling of
overflow-Tunable digital filters-function approximation.
UNIT-IV
Analysis of finite Word length effects The Quantization process and
errors- Quantization of fixed -point and floating -point Numbers-
Analysis of coefficient Quantization effects - Analysis of Arithmetic
Round-off errors, Dynamic range scaling-signal- to- noise ratio in Low
-order IIR filters-Low-Sensitivity Digital filters-Reduction of Product
round-off errors using error feedback-Limit cycles in IIR digital filters-
Round-off errors in FFT Algorithms.
UNIT -V
Power Spectrum Estimation Estimation of spectra from Finite Duration
Observations signals ? Non-parametric methods for power spectrum
Estimation ? parametric method for power spectrum Estimation,
PS
41
Estimation of spectral form-Finite duration observation of signals-Non-
parametric methods for power spectrum estimation-Walsh methods-
Blackman & torchy method.
REFERENCE BOOKS:
1.
Digital signal processing-sanjit K. Mitra-TMH second edition.
2.
Discrete Time Signal Processing ? Alan V.Oppenheim, Ronald W.Shafer
- PHI-1996 1st edition-9th reprint
3
Digital Signal Processing principles, algorithms and Applications ?
John G.Proakis -PHI ?3rd edition-2002
4.
Digital Signal Processing ? S.Salivahanan, A.Vallavaraj, C. Gnanapriya
? TMH - 2nd reprint-2001
5.
Theory and Applications of Digital Signal Proceesing-LourensR.
Rebinar & Bernold
6.
Digital Filter Analysis and Design-Auntonian-TMH
42
2013-14
I ? II
L
P
Credits
4
-
3
(ELECTIVE II)
GENERATION & MEASUREMENTS OF HIGH
VOLTAGES
UNIT -I
Electrostatic fields and field stress control : Electric fields in
homogeneous Isotropic materials and in multi dielectric media-Simple
configurations-field stress control. Methods of computing electrostatic
fields-conductive analogues-Impedance networks Numerical
techniques-finite difference method-finite element method and charge
simulation method.
UNIT-II
Generation of High AC & DC Voltages: Direct Voltages : AC to DC
conversion methods electrostatic generators-Cascaded Voltage
Multipliers.
Alternating Voltages : Testing transformers-Resonant circuits and their
applications, Tesla coil.
UNIT-III
Generation of Impulse Voltages : Impulse voltage specifications-
Impulse generations circuits-Operation, construction and design of
Impulse generators-Generation of switching and long duration
impulses.
Impulse Currents : Generation of High impulse currents and high
current pulses.
UNIT-IV
Measurement of High AC & DC Voltages : Measurement of High D.C.
Voltages : Series resistance meters, voltage dividers and generating
voltmeters.
Measurement of High A.C. Voltages : Series impedance meters
electrostatic voltmeters potential transformers and CVTS-voltage
dividers and their applications.
PS
43
UNIT-V
Measurement of Peak Voltages : Sphere gaps, uniform field gaps, rod
gaps. Chubb-Fortesque methods. Passive and active rectifier circuits
for voltage dividers.
Measurement of Impulse Voltages : Voltage dividers and impulse
measuring systems-generalized voltage measuring circuits-transfer
characteristics of measuring circuits-L.V. Arms for voltage dividers-
compensated dividers.
Measurement of Impulse Currents : Resistive shunts-current
transformers-Hall Generators and Faraday generators and their
applications-Impulse Oscilloscopes.
TEXT BOOKS :
1.
High Voltage Engineering ? by E.Kuffel and W.S.Zaengl. Pergaman
press Oxford, 1984.
2.
High Voltage Engineering ? by M.S.Naidu and V.Kamaraju, Mc.Graw-
Hill Books Co., New Delhi, 2nd edition, 1995.
REFERENCE BOOKS :
1.
High Voltage Technology ? LL Alston, Oxford University Press 1968.
2.
High Voltage Measuring Techniques ? A. Schwab MIT Press,
Cambridge,USA, 1972.
3.
Relevant I.S. and IEC Specifications.
44
2013-14
I ? II
L
P
Credits
4
-
3
(ELECTIVE II)
PROGAMMABLE LOGIC CONTROLLERS &
APPLICATIONS
UNIT -I
PLC Basics: PLC system, I/O modules and interfacing, CPU processor,
programming equipment, programming formats, construction of PLC
ladder diagrams, devices connected to I/O modules.
UNIT-II
PLC Programming: Input instructions, outputs, operational
procedures, programming examples using contacts and coils. Drill press
operation. Digital logic gates, programming in the Boolean algebra
system, conversion examples. Ladder diagrams for process control:
Ladder diagrams and sequence listings, ladder diagram construction
and flow chart for spray process system.
UNIT -III
PLC Registers: Characteristics of Registers, module addressing,
holding registers, input registers, output registers. PLC Functions: Timer
functions and Industrial applications, counters, counter function
industrial applications, Arithmetic functions, Number comparison
functions, number conversion functions.
UNIT-IV
Data Handling functions: SKIP, Master control Relay, Jump, Move,
FIFO, FAL, ONS, CLR and Sweep functions and their applications. Bit
Pattern and changing a bit shift register, sequence functions and
applications, controlling of two axis and three axis Robots with PLC,
Matrix functions.
UNIT -V
Analog PLC operation: Analog modules and systems, Analog signal
processing, multi bit data processing, analog output application
examples, PID principles, position indicator with PID control, PID
modules, PID tuning, PID functions.
PS
45
REFERENCE BOOKS:
1.
Programmable Logic Controllers ? Principle and Applications by John
W. Webb and Ronald A. Reiss, Fifth Edition, PHI
2.
Programmable Logic Controllers ? Programming Method and
Applications by JR. Hackworth and F.D Hackworth Jr. ? Pearson, 2004.
3.
Introduction to Programmable Logic Controllers- Gary Dunning-
Cengage Learning.
4.
Programmable Logic Controllers ?W.Bolton-Elsevier publisher
46
2013-14
I ? II
L
P
Credits
4
-
3
(ELECTIVE-II)
MODERN CONTROL THEORY
UNIT ?I
State Variable Analysis The concept of state ? State Equations for
Dynamic systems ? State diagram--- - Linear Continuous time model
for physical systems ? Existence and Uniqueness of Solutions to
Continuous ? Time State Equations ? Solutions ? Linear Time Invariant
Continuous ? Time State Equations ? State transition matrix and it's
properties
UNIT ? II
State Variable Techniques General concept of Controllability - General
concept of Observability Controllability tests for Continuous &Time
Invariant systems - Observability tests for Continuous &Time Invariant
systems - Controllability and Observability of state model in Jordan
Canonical form - Controllability and Observability Canonical forms of
State model ? State feedback controller design through pole assignment.
UNIT ? III
Non Linear Systems ? 1 Introduction ? Non Linear Systems ? Types
of Non ? Linearities ? Saturation ? Dead ? Zone ? Backlash ? Jump
Phenomenon etc; - Singular Points ? Introduction to Linearization of
nonlinear systems, properties of Non Linear Systems ? Describing
function ? describing function analysis of nonlinear systems- Stability
analysis of Non ? Linear systems through describing functions.
UNIT ? IV
Non Linear Systems ? 11 Introduction to phase ? plane analysis,
Method of Isoclines for Constructing Trajectories, singular points,
phase ? plane analysis of nonlinear control systems.
UNIT ? V
Stability Analysis Stability in the sense of Lyapunov, Lyapunov's
stability and Lyapunov's instability theorems ? Stability Analysis of
PS
47
the Linear Continuous time invariant systems by Lyapunov second
method ? Generation of Lyapunov functions ? Variable gradient method
? Krasooviski's method.
TEXT BOOKS:
1.
Modern Control System Theory by M. Gopal ? New Age International
? 1984
2.
Modern Control Engineering by Ogata. K ? Prentice Hall ? 1997
3.
Nonlinear systems, Hassan K. Klalil, Prentice Hall, 1996
4.
Modern control systems, Richard C. Dorf and Robert H. Bishop, 11th
Edition, Pearson Edu, India, 2009
48
2013-14
I ? I
L
P
Credits
-
4
2
SIMULATION LABORATORY
Any 10 of the following experiments are to be conducted
List of Experiments:
1.
Y Bus formation for p systems with and without mutual coupling, by
Singular transformation.
2.
Y Bus formation for p systems with and without mutual coupling, by
inspection method.
3.
Determination of bus currents, bus power and line flow for a specified
system voltage (Bus) Profile
4.
Formation of Z-bus, using Z-bus building Algorithm without mutual.
5.
ABCD parameters: Formation for symmetric II/I configuration.
Verification of AD- BC=1 Determination of coefficient and regulation
6.
Determination of power angle diagrams for salient and non-salient pole
synchronous m/c s, reluctance power, excitation, emf and regulation.
7.
To determine I) Swing curve II) critical clearing time for a single m/c
connected to infinity bus through a pair of identical transmission
lines, 3-phase fault on one of the lines for variation of inertia constant/
line parameters /fault location/clearing time/pre-fault electrical output.
8.
Formation of Jacobian for a system not exceeding 4 buses *(no PV
buses) in polar coordinates
9.
Write a program to perform load flow using Gauss- Seidel method (only
p q bus)
10.
To determine fault currents and voltages in a single transmission line
systems with star-delta transformers at a specified location for SLGF,
DLGF.
11. Load flow analysis using Gauss- Siedel method for both pq and pv
buses.
PS
49
12.
Load flow analysis using NR method for both pq and pv buses.
13. Fast decoupled flow method for both pq and pv buses.
14.
Optimal Generator Scheduling for Thermal power plants.
15. Economic dispatch using lambda-iteration method
50
2013-14
I ? II
L
P
Credits
4
-
3
POWER SYSTEM DYNAMICS AND STABILITY
UNIT-I
System Dynamics : Synchronous machine model in state space from
computer representation for excitation and governor system ?modeling
of loads and induction machines.
UNIT-II
Steady state stability ? steady state stability limit ? Dynamics Stability
limit ? Dynamic stability analysis ? State space representation of
synchronous machine connected to infinite bus-time response ?
Stability by eigen value approach.
UNIT-III
Digital Simulation of Transient Stability : Swing equation machine
equations ? Representation of loads ? Alternate cycle solution method
? Direct method of solution ? Solution Techniques : Modified Euler
method ? Runge Kutta method ? Concept of multi machine stability.
UNIT-IV
Effect of governor action and excite on power system stability effect of
saturation, saliency & automatic voltage regulators on stability.
UNIT-V
Excitation Systems : Rotating Self-excited Exciter with direct acting
Rheostatic type voltage regulator ? Rotating main and Pilot Exciters
with Indirect Acting Rheostatic Type Voltage Regulator ? Rotating
Main Exciter, Rotating Amplifier and Static Voltage Regulator ? Static
excitation scheme ? Brushless excitation system.
REFERENCE BOOKS :
1.
Power System Stability by Kimbark Vol. I&II, III
2.
Power System control and stability by Anderson and Fund
3.
Power systems stability and control by PRABHA KUNDUR
4.
Computer Applications to Power Systems?Glenn.W.Stagg & Ahmed.
H.El.Abiad
5.
Computer Applications to Power Systems ? M.A.Pai
6.
Power Systems Analysis & Stability ? S.S.Vadhera Khanna Publishers
PS
51
I ? II
L
P
Credits
4
-
3
FLEXIBLE AC TRANSMISSION SYSTEMS
UNIT-I
FACTS concepts, Transmission interconnections, power flow in an
AC System, loading capability limits, Dynamic stability considerations,
importance of controllable parameters, basic types of FACTS controllers,
benefits from FACTS controllers.
UNIT-II
Voltage source converters : Single phase, three phase, full wave bridge
converters, transformer connections for 12 pulse, 24 and 48 pulse
operation. Three level voltage source converter, pulse width modulation
converter, basic concept of current source converters, comparison of
current source converters with voltage source converters.
UNIT- III
Static shunt compensation : Objectives of shunt compensation,
midpoint voltage regulation, voltage instability prevention,
improvement of transient stability, Power oscillation damping, methods
of controllable var generation, variable impedance type static var
generators, switching converter type var generators, hybrid var
generators.
UNIT- IV
SVC and STATCOM : The regulation and slope transfer function and
dynamic performance, transient stability enhancement and power
oscillation damping, operating point control and summary of
compensation control.
UNIT-V
Static series compensators : Concept of series capacitive
compensation, improvement of transient stability, power oscillation
damping, functional requirements. GTO thyristor controlled series
capacitor (GSC), thyristor switched series capacitor (TSSC), and
thyristor controlled series capacitor (TCSC), control schemes for GSC,
TSSC and TCSC.
52
2013-14
TEXT BOOK :
1.
"Understanding FACTS Devices" N.G.Hingorani and L.Guygi, IEEE
Press. Indian Edition is available:--Standard Publications
2.
Sang.Y.H and John.A.T, "Flexible AC Transmission systems" IEEE
Press (2006).
3.
HVDC & FACTS Controllers: applications of static converters in power
systems- Vijay K.Sood- Springer publishers
PS
53
I ? II
L
P
Credits
4
-
3
REAL TIME CONTROL OF POWER SYSTEMS
UNIT-I
State Estimation : Different types of State Estimations, Theory of WLS
state estimation, sequential and non-sequential methods to process
measurements. Bad data Observability, Bad data detection, identification
and elimination.
UNIT-II
Security and Contingency Evaluation : Security concept, Security
Analysis and monitoring, Contingency Analysis for Generator and
line outages by iterative linear power flow method, Fast Decoupled
model, and network sensitivity methods.
UNIT-III
Computer Control of Power Systems : Need for real time and computer
control of power systems, operating states of a power system, SCADA
- Supervisory control and Data Acquisition systems implementation
considerations, energy control centres, software requirements for
implementing the above functions.
UNIT ?III
Voltage Stability, voltage collapse, and voltage security, relation of
voltage stability to rotor angle stability. Voltage stability analysis
Introduction to voltage stability analysis `P-V' curves and `Q-V' curves,
voltage stability in mature power systems, long-term voltage stability,
power flow analysis for voltage stability, voltage stability static indices
and Research Areas.
UNIT-V
Application of AI and ANN in Power System : Basic concepts and
definitions, algorithms for load flow, short term load forecasting, fault
diagnosis and state estimation.
54
2013-14
REFERENCE BOOKS :
1.
John J.Grainger and William D.Stevenson, Jr. : Power System Analysis,
McGraw-Hill, 1994, International Edition
2.
Allen J.Wood and Bruce F.Wollenberg : Power Generation operation
and control, John Wiley & Sons, 1984
3.
R.N.Dhar : Computer Aided Power Systems Operation and Analysis,
Tata McGraw Hill, 1982
4.
L.P.Singh : Advanced Power System Analysis and Dynamics, Wiley
Eastern Ltd. 1986
5.
Prabha Kundur : Power System Stability and Control -, McGraw Hill,
1994
6.
P.D.Wasserman : `Neural Computing : Theory and Practice' Van
Nostrand - Feinhold, New York.
PS
55
I ? II
L
P
Credits
4
-
3
ADVANCED POWER SYSTEM PROTECTION
UNIT -I
Static Relays classification and Tools : Comparison of Static with
Electromagnetic Relays, Basic classification, Level detectors and
Amplitude and phase Comparators ? Duality ? Basic Tools ? Schmitt
Trigger Circuit, Multivibrators, Square wave Generation ? Polarity
detector ? Zero crossing detector ? Thyristor and UJT Triggering
Circuits. Phase sequence Filters ? Speed and reliability of static relays.
UNIT -II
Amplitude and Phase Comparators (2 Input) : Generalized equations
for Amplitude and Phase comparison ? Derivation of different
characteristics of relays ? Rectifier Bridge circulating and opposed
voltage type amplitude comparators ? Averaging & phase splitting
type amplitude comparators ? Principle of sampling comparators.
Phase Comparison : Block Spike and phase Splitting Techniques ?
Transistor Integrating type, phase comparison, Rectifier Bridge Type
Comparison ? Vector product devices.
UNIT-III
Static over current (OC) relays ? Instantaneous, Definite time, Inverse
time OC Relays, static distance relays, static directional relays, static
differential relays, measurement of sequence impedances in distance
relays, multi input comparators, elliptic & hyperbolic characteristics,
switched distance schemes, Impedance characteristics during Faults
and Power Swings.
UNIT-IV
Carrier plot protection scheme: carrier current protection schemes,
relative merits & demerits, carrier aided distance protection schemes,
transfer schemes, blocking scheme and acceleration schemes.
Differential relay Principle and characteristics, maloperation of
differential relay, protection of transformers, protection of generators.
56
2013-14
UNIT -V
Numerical Protection: Introduction , numerical relay, numerical relaying
algorithms, mann-morrison technique,Differential equation technique,
discrete fourier transform technique, rationalised harr transform
technique, wavelet transform technique, numerical overcurrent
protection , numerical distance protection , numerical differential
protection.
REFERENCE BOOKS :
1.
Power System Protection with Static Relays ? by TSM Rao
2.
Protective Relaying Vol-II Warrington
3.
Art & Science of Protective Relaying - C R Mason
4.
Power System Stability Kimbark Vol-II
5.
Power system protection & switchgear by Badri Ram & D N viswakarma.
6.
Electrical Power System Protection ?C.Christopoulos and A.Wright-
Springer
7.
Protection & Switchgear ?Bhavesh Bhalaja,R.P Maheshwari, Nilesh
G.Chothani-Oxford publisher
PS
57
I ? II
L
P
Credits
4
-
3
(ELECTIVE ? III)
SMART GRID
UNIT-I
Introduction to Smart Grid: Evolution of Electric Grid, Concept of
Smart Grid, Definitions, Need of Smart Grid, Functions of Smart Grid,
Opportunities & Barriers of Smart Grid, Difference between conventional
& smart grid, Concept of Resilient & Self Healing Grid, Present
development & International policies on Smart Grid. Case study of
Smart Grid.
UNIT-II
Smart Grid Technologies: Part 1: Introduction to Smart Meters, Real
Time Prizing, Smart Appliances, Automatic Meter Reading(AMR),
Outage Management System(OMS), Plug in Hybrid Electric
Vehicles(PHEV), Vehicle to Grid, Smart Sensors, Home & Building
Automation, Phase Shifting Transformers.
UNIT-III
Smart Grid Technologies: Part 2: Smart Substations, Substation
Automation, Feeder Automation. Geographic Information System(GIS),
Intelligent Electronic Devices(IED) & their application for monitoring
& protection, Smart storage like Battery, SMES, Pumped Hydro,
Compressed Air Energy Storage, Wide Area Measurement
System(WAMS), Phase Measurement Unit(PMU).
UNIT -IV
Microgrids and Distributed Energy Resources: Concept of micro grid,
need & applications of microgrid, formation of microgrid, Issues of
interconnection, protection & control of microgrid. Plastic & Organic
solar cells, Thin film solar cells, Variable speed wind generators, fuelcells,
microturbines, Captive power plants, Integration of renewable energy
sources.
UNIT-V
Power Quality Management in Smart Grid: Power Quality & EMC in
Smart Grid, Power Quality issues of Grid connected Renewable Energy
58
2013-14
Sources, Power Quality Conditioners for Smart Grid, Web based Power
Quality monitoring, Power Quality Audit.
Information and Communication Technology for Smart Grid:
Advanced Metering Infrastructure (AMI), Home Area Network (HAN),
Neighborhood Area Network (NAN), Wide Area Network (WAN).
TEXT BOOKS:
1.
Ali Keyhani, Mohammad N. Marwali, Min Dai "Integration of Green
and Renewable Energy in Electric Power Systems", Wiley
2.
Clark W. Gellings, "The Smart Grid: Enabling Energy Efficiency and
Demand Response",CRC Press
3.
Janaka Ekanayake, Nick Jenkins, Kithsiri Liyanage, Jianzhong Wu,
Akihiko Yokoyama,"Smart Grid: Technology and Applications", Wiley
4.
Jean Claude Sabonnadi?re, Nouredine Hadjsa?d, "Smart Grids", Wiley
Blackwell 19
5.
Peter S. Fox Penner, "Smart Power: Climate Changes, the Smart Grid,
and the Future of Electric Utilities", Island Press; 1 edition 8 Jun 2010
6.
S. Chowdhury, S. P. Chowdhury, P. Crossley, "Microgrids and Active
Distribution Networks." Institution of Engineering and Technology,
30 Jun 2009
7.
Stuart Borlase, "Smart Grids (Power Engineering)", CRC Press
REFERENCE BOOKS:
1.
Andres Carvallo, John Cooper, "The Advanced Smart Grid: Edge Power
Driving Sustainability: 1", Artech House Publishers July 2011
2.
James Northcote, Green, Robert G. Wilson "Control and Automation of
Electric Power Distribution Systems (Power Engineering)", CRC Press
3.
Mladen Kezunovic, Mark G. Adamiak, Alexander P. Apostolov, Jeffrey
George Gilbert "Substation Automation (Power Electronics and Power
Systems)", Springer
4.
R. C. Dugan, Mark F. McGranghan, Surya Santoso, H. Wayne Beaty,
"Electrical Power System Quality", 2nd Edition, McGraw Hill Publication
5.
Yang Xiao, "Communication and Networking in Smart Grids", CRC
Press
PS
59
I ? II
L
P
Credits
4
-
3
(ELECTIVE III)
POWER QUALITY
UNIT-I
Introduction Overview of Power Quality - Concern about the Power
Quality - General Classes of Power Quality Problems ? Transients -
Long-Duration Voltage Variations - Short-Duration Voltage Variations -
Voltage Unbalance - Waveform Distortion - Voltage fluctuation - Power
Frequency Variations - Power Quality Terms - Voltage Sags and
Interruptions - Sources of Sags and Interruptions ? Nonlinear loads.
UNIT-II
Transient Over Voltages Source of Transient Over Voltages - Principles
of Over Voltage Protection - Devices for Over Voltage Protection -
Utility Capacitor Switching Transients - Utility Lightning Protection -
Load Switching Transient Problems - Computer Tools for Transient
Analysis
UNIT-III
Harmonic Distortion and solutions Voltage vs. Current Distortion -
Harmonics vs. Transients - Power System Quantities under
Nonsinusoidal Conditions - Harmonic Indices ? Sources of harmonics
- Locating Sources of Harmonics ? System Response Characteristics -
Effects of Harmonic Distortion ? Interharmonics - Harmonic Solutions
Harmonic Distortion Evaluation - Devices for Controlling Harmonic
Distortion - Harmonic Filter Design - Standards on Harmonics
UNIT- IV
Long Duration Voltage Variations Principles of Regulating the Voltage
- Device for Voltage Regulation - Utility Voltage Regulator Application
- Capacitor for Voltage Regulation -
End-user Capacitor
Application - Regulating Utility Voltage with Distributed Resources ?
Flicker
60
2013-14
UNIT-V
Distributed Generation and Power Quality Resurgence of Distributed
Generation - DG Technologies - Interface to the Utility System - Power
Quality Issues - Operating Conflicts - DG on Low Voltage Distribution
Networks - Interconnection standards - Wiring and Grounding - Typical
Wiring and Grounding Problems - Solution to Wiring and grounding
Problems
TEXTBOOKS
1.
Electrical Power Systems Quality, Dugan R C, McGranaghan M F,
Santoso S, and Beaty H W, Second Edition, McGraw-Hill, 2002.
2.
Power Quality Primer, Kennedy B W, First Edition, McGraw-Hill, 2000.
REFERENCES
1.
Understanding Power Quality Problems: Voltage Sags and Interruptions,
Bollen M H J, First Edition, IEEE Press; 2000.
2.
Power System Harmonics, Arrillaga J and Watson N R, Second Edition,
John Wiley & Sons, 2003.
3.
Electric Power Quality control Techniques, W. E. Kazibwe and M. H.
Sendaula, Van Nostrad Reinhold, New York.
4.
Power Quality c.shankaran, CRC Press, 2001
5.
Harmonics and Power Systems ?Franciso C.DE LA Rosa-CRC Press
(Taylor & Francis)
6.
Power Quality in Power systems and Electrical Machines-Ewald F.fuchs,
Mohammad A.S. Masoum-Elsevier
PS
61
I ? II
L
P
Credits
4
-
3
(ELECTIVE ? III)
POWER SYSTEM RELIABILITY
UNIT-I
Basic probability theory ? rules for combining probabilities of events ?
Bernoulli`s trials ? probability density and distribution functions ?
binomial- distributions ? expected value and standard deviation of
binomial distribution.
UNIT -II
Network Modelling and Reliability Analysis of Series, Parallel, Series-
Parallel networks ? complex networks ? decomposition method
Reliability functions f(t), F(t), R(t), h(t) and their relationship ?
exponential distributions ? Expected value and standard deviation of
exponentional distribution ? Bath tub curve ? reliability analysis of
series parallel networks using exponential distribution ? reliability
measures MTTF, MTTR, MTBF
UNIT ?III
Markov chains ? concept of stochastic transitional probability Matrix,
Evaluation of limiting state Probabilities ? Markov processes one
component repairable system ? time dependent probability evaluation
using Laplace transform approach ? evaluation of limiting state
probabililties using STPM ? two component repairable models ?
Frequency and duration concept ? Evaluation of frequency of
encountering state, mean cycletime, for one, two component repairable
models ? evaluation of cumulative probability and cumulative frequency
of encountering merged states
UNIT-IV
Generation system reliability analysis ? reliability model of a generation
system ? recursive relation for unit addition and removal ? load
modelling ? merging of generation load model ? evaluation of transition
rates for merged state model ? cumulative Probability, cumulative
frequency of failure evaluation ? LOLP, LOLE.
62
2013-14
UNIT-V
Composite system reliability analysis decomposition method ?
distribution system reliability analysis ? radial networks ? weather
effects on transmission lines ? Evaluation of load and energy indices.
REFERENCE BOOKS :
1.
Reliability Evaluation of Engg. System ? R.Billinton, R.N.Allan, Plenum
Press, New York.
2.
Reliability Evaluation of Power System ? R.Billinton, R.N.Allam, Plenum
Press, New York
3.
An Introduction to Realiability and Maintainability Engineering. Sharies
E Ebeling, TATA McGraw Hill ? Edition
PS
63
I ? II
L
P
Credits
4
-
3
(ELECTIVE III)
VOLTAGE STABILITY
UNIT-I
Reactive Power flow and voltage stability in power systems: Physical
relationship indicating dependency of voltage on reactive power flow
- reactive power, transient stability; Q-V curve; definition of voltage
stability, voltage collapse and voltage security. Voltage collapse
phenomenon, Factors of voltage collapse, effects of voltage collapse,
voltage collapse analysis.
UNIT-II
Power system loads : Load characteristics that influence voltage
stability such as ? Discharge lighting, Induction motor, Air conditioning
and heat pumps, Electronic power supplies, Over Head lines and cables.
UNIT-III
Reactive Power compensation : Generation and absorption of reactive
power ? Reactive power compensators & voltage controllers : - shunt
capacitors, synchronous phase modifier ? static VAR system ? on load
tap changing transformer, booster transformers.
UNIT-IV
Voltage stability static indices : Development of voltage collapse index
? power flow studies ? singular value decomposition ? minimum
singular value of voltage collapse ? condition number as voltage
collapse index.
UNIT-V
voltage stability margins & Improvement of voltage stability: Stability
margins, voltage stability margin of uncompensated and compensated
power system . Dynamic voltage stability ? voltage security , Methods
of improving voltage stability and its practical aspects.
REFERENCES:
1.
Performance operation and control of EHV power transmission Systems
A. chakrabarti, D.P.Kothari, A.K. Mukhopadhyay, A.H. Wheeler
publishing, 1995.
2.
Power system Voltage stability - C.W. Taylor , Mc. Graw Hill, 1994
64
2013-14
I ? II
L
P
Credits
4
-
3
(ELECTIVE IV)
POWER SYSTEM DEREGULATION
UNIT-I
Need and conditions for deregulation. Introduction of Market structure,
Market Architecture, Spot market, forward markets and settlements.
Review of Concepts marginal cost of generation, least-cost operation,
incremental cost of generation. Power System Operation.
UNIT-II
Electricity sector structures and Ownership /management, the forms of
Ownership and management. Different structure model like Monopoly
model, Purchasing agency model, wholesale competition model, Retail
competition model.
UNIT-III
FRAMEWORK and methods for the analysis of Bilateral and pool
markets, LMP based markets, auction models and price formation,
price based unit commitment, country practices.
UNIT-IV
Transmission network and market power. Power wheeling transactions
and marginal costing, transmission costing. Congestion management
methods- market splitting, counter-trading; Effect of congestion on
LMPs- country practices
UNIT-V
Ancillary Services and System Security in Deregulation. Classifications
and definitions, AS management in various markets- country practices.
Technical, economic, & regulatory issues involved in the deregulation
of the power industry.
REFERENCE BOOKS:
1.
Power System Economics: Designing markets for electricity - S. Stoft
2.
Power generation, operation and control, -J. Wood and B. F. Wollenberg
PS
65
3.
Operation of restructured power systems - K. Bhattacharya, M.H.J.
Bollen and J.E. Daalder
4.
Market operations in electric power systems - M. Shahidehpour, H.
Yamin and Z. Li
5.
Fundamentals of power system economics - S. Kirschen and G. Strbac
6.
Optimization principles: Practical Applications to the Operation and
Markets of the Electric Power Industry - N. S. Rau
7.
Competition and Choice in Electricity - Sally Hunt and Graham
Shuttleworth
66
2013-14
I ? II
L
P
Credits
4
-
3
(ELECTIVE IV)
HIGH VOLTAGE TESTING TECHNIQUES
UNIT-I
Non Destructive Testing Techniques : Measurement of DC Resistivity
? Dielectric loss and dielectric constant of insulating materials ? Schering
bridge method ? Transformer ratio arm bridge for high voltage and
high current applications ? null detectors.
UNIT-II
High Voltage Testing of Power Apparatus : Need for testing standards
? Standards for porcelain/Glass insulators-Classification of porcelain/
glass insulator tests ? Tests for cap and pin porcelain/Glass insulators.
UNIT-III
High voltage AC testing methods-Power frequency tests-Over voltage
tests on insulators, Isolators, Circuit Breakers and power cables.
Artificial Contamination Tests : Contamination flashover phenomena-
Contamination Severity-Artificial contamination tests-Laboratory
Testing versus in-Service Performance-Case study.
UNIT-IV
Impulse Testing : Impulse testing of transformers, insulators, Surge
diverters, Bushings, cables, circuit breakers.
UNIT -V
Partial Discharge Measurement : PD equivalent model-PD currents-
PD measuring circuits-Straight and balanced detectors-Location and
estimation of PD in power apparatus-PD measurement by non electrical
methods-Calibration of PD detectors. RIV Measurements : Radio
Interference ? RIV ? Measurement of RI and RIV in laboratories and in
field. Different test arrangements and their limitations.
PS
67
REFERENCE BOOKS :
1.
High Voltage Engineering ? by E.KUFFEL and W.S.ZAENGL, Pergamon
press, Oxford 1984.
2.
High Voltage Engineering ? by M.S.Naidu and V.Kamaraju, Tata Mc
Graw Hill Publishing Company Limited, New Delhi ? 2001.
3.
Discharge Detection in H.V. Equipment ? by KREUGER, F.H. Haywood
London ? 1964.
4.
Outdoor Insulators ? by Gorur & Cherney.
5.
H.V. Testing Techniques Halfly
68
2013-14
I ? II
L
P
Credits
4
-
3
(ELECTIVE IV)
POWER SYSTEM TRANSIENTS
UNIT-I
Basic Concepts and Simple Switching Transients;- Switching an
LR,LC,RLC circuits
Transients Analysis of Three-Phase power Systems:? Symmetrical
components in Three-phase Systems, Sequence Components for
Unbalanced Network Impedances, the Sequence Networks , analysis
of Unsymmetrical Three-Phase Faults-single line-to-Ground Fault, Three
phase-to-ground fault.
UNIT -II
Travelling Waves:- Velocity of Travelling waves and Characteristic
Impedance, Energy Contents of Travelling Waves, Attenuation and
Distortion of Electromagnetic Waves, telegraph equations-lossless line,
distortion less line, Reflection and Refraction of Travelling Waves,
Reflection of Travelling Waves against Transformer-and-Generator-
windings, the Origin Transient Recovery voltages, bewley-lattice
diagram. travelling waves and multi conductor system.
UNIT-III
Switching Transients:- arc interruption in circuit breaker , transient
recovery voltage, arc-circuit interaction, interruption of capacitive
currents, interruption of inverse currents, interruption of fault current
in transmission line and transformers.
UNIT-IV
Power System Transient Recovery Voltages:-Characteristics of the
Transient Voltage- Short-circuit test duties based on IEC 60056
(1987),ANSI/IEEE Standards, the Harmonization between IEC and ANSI/
IEEE Standards with respect to Short-circuit Test duties, transient
recovery voltage for Different types of faults.
PS
69
UNIT-V
Lightning ?Induced Transients:-Mechanism of Lightning, wave shape
of the lightning current, Direct lighting Stroke to transmission line
towers, direct lightening stroke to a line, lightning protection scheme.
Numerical simulation of electrical transients, The Electromagnetic
Transient Program, principles of numerical techniques used in transient
simulation.
REFERENCE BOOKS :
1.
Electrical Transients in Power System by Allen Greenwood, McGraw
Hill 1990
2.
Power system grounding & transients by A.P.Sakis Meliopolous.
3.
"Transients in power systems" by Lou Van Sluis
70
2013-14
I ? II
L
P
Credits
4
-
3
(ELECTIVE IV)
DEMAND SIDE ENERGY MANAGEMENT
UNIT-I
Energy Audit and Energy management information systems: Energy
audit: Definitions-Need-concepts-Types of energy audit; Energy
management information systems: Introduction-Need-components-
designing-using the system-identifying plant outages
UNIT-II
Energy Economics: Introduction-Cost benefit risk analysis-Payback
period-Straight line depreciation-Sinking fund depreciation--Reducing
balance depreciation-Net present value method-Internal rate of return
method-Profitability index for benefit cost ratio.
UNIT-III
Energy Conservation in Electric utilities and Industry: Electrical load
management: Energy and load management devices-Conservation
strategies; conservation in electric utilities and industry: Introduction-
Energy conservation in utilities by improving load factor-Utility voltage
regulation-Energy conservation in Industries-Power factor improvement.
Energy ?efficient electric motors: Energy efficient motors-construction
and technical features-case studies of EEMs with respect to cost
effectiveness-performance characteristics; Economics of EEMs and
system: life cycle-direct savings and payback analysis-efficiency factor
or efficiency evaluation factor
UNIT-IV
Electric Lighting: Introduction-Need for an energy management
program-Building analysis-Modification of existing systems-
Replacement of existing systems-priorities:
Illumination requirement : Task lighting requirements-lighting levels-
system modifications-non illumination modifications-lighting for non
task areas-reflectances-space geometry ;System elements: light sources
- characteristics of families of lamps-lamp substitution in an existing
PS
71
systems-selection of Higher efficiency lamps for a new system-
Luminaries-ballasts-energy conservation in lighting.
UNIT-V
Space Heating ,Ventilation, Air-Conditioning(HVAC) and Water Heating:
Introduction-Heating of buildings-Transfer of Heat-Space heating
methods-Ventilation and air-conditioning-Insulation-Cooling load-
Electric water heating systems-Energy conservation methods.
Co-generation and storage: Combined cycle cogeneration-energy
storage: pumped hydro schemes-compressed air energy
storage(CAES)-storage batteries-superconducting magnetic energy
storage (SMES)
REFERENCES:
1.
Energy management Hand book by Wayne C.Turner,John wiley and
sons publications
2.
Electric Energy Utilization and Conservation by S C Tripathy,Tata
McGraw hill publishing company ltd.New Delhi
3.
Energy efficient electric motors selection and application by John
C.Andreas
4.
Hand book on Energy Audit and Management by Amit kumar
Tyagi,published by TERI (Tata energy research Institute)
5.
Energy management by Paul W.O' Callaghan McGraw hill book company
6.
Energy conversion systems by Rakosh Das Begamudre New age
international publishers
72
2013-14
I ? II
L
P
Credits
-
4
2
POWER SYSTEMS LABORATORY
List of Experiments:
1.
Determination of Sequence Impedance of an Alternator.
2.
Determination of Sequence impedance of an Alternator by fault
Analysis.
3.
Measurement of Sequence Impedance of a 3 phase Transformer.
4.
Power angle characteristics of a salient pole Synchronous Machine.
5.
Scott connection of Transformers.
6.
ABCD parameter.
7.
Break down characteristics of a Sphere gap.
8.
Determination of Breakdown strength of transformer oil.
9.
Determination of leakage current of pin insulator.
10.
Voltage distribution across the string insulator.
This post was last modified on 16 March 2021