Download GTU (Gujarat Technological University) BE/BTech (Bachelor of Engineering / Bachelor of Technology) 2019 Summer 6th Sem New 2164001 Design Of Concrete Structures Previous Question Paper
Seat No.: ________ Enrolment No.___________
GUJARAT TECHNOLOGICAL UNIVERSITY
BE - SEMESTER ?VI(NEW) ? EXAMINATION ? SUMMER 2019
Subject Code:2164001 Date:10/05/2019
Subject Name:Design of Concrete Structures
Time:10:30 AM TO 01:30 PM Total Marks: 70
Instructions:
1. Attempt all questions.
2. Make suitable assumptions wherever necessary.
3. Figures to the right indicate full marks.
4. Use of IS 456, IS 875 is allowed.
5. Draw neat and clean sketches.
MARKS
Q.1 (a) Write advantages of limit state method (LSM) over working stress
method (WSM) of structural design philosophy.
07
(b) Calculate moment carrying capacity of a rectangular beam with
250 mm ? 400 mm overall section and having Ast = 1800 mm
2
. Assume
effective cover provided is 40 mm at tension side. Adopt M 30 and
Fe 415 grade of materials.
07
Q.2 (a) Design a reinforced concrete rectangular beam section of size
300 mm ? 600 mm overall from architectural considerations. The beam
is subjected to design moment of resistance 300 kN.m. The effective
cover to reinforcement is taken as 50 mm. Adopt M 20 and Fe 415 grade
of materials.
07
(b) Design a T-beam section with a flange width of 1250 mm, a flange depth
of 100 mm, a web width of 250 mm and an effective depth of 500 mm,
which is subjected to a factored moment of 560 kN.m. The concrete mix
is to be used is of grade M 20 and steel is grade Fe 415.
07
OR
(b) Design a cantilever beam of effective span of 2 m to sustain the uniformly
distributed load of 20 kN/m. Use M 25 grade of concrete and Fe 415
grade of steel.
07
Q.3 (a) Design a shear reinforcement for a simply supported RC beam subjected
to U.D.L. of 25 kN/m over a span of 3.6 m and having cross section of
230 mm width and 450 mm overall depth is reinforced with
3 # 16 mm ? HYSD steel of grade Fe 415, placed at an effective cover
of 50 mm. Use grade of concrete M 20.
07
(b) Design a slab over a room 4 m ? 5 m as per IS code. The slab is supported
on masonry walls all round with adequate restraint and the corners are
held down. The live load on the slab is 3 kN/m
2
. The slab has a bearing
of 150 mm on the supporting walls. Check for limit state of
serviceability.
07
OR
Q.3 (a) A simply supported RC beam of size 350 mm ? 550 mm overall is
reinforced with 3#20 mm ? of Fe 415 grade of steel. Determine the
anchorage length of the bars at the simply supported end if it is subjected
to a factored shear force of 350 kN at the centre of 300 mm wide masonry
support. The concrete mix of grade M 20 is to be used.
07
(b) Design one way simply supported slab of 9 m ? 4 m clear dimension, the
width of the support being 300 mm. The live load on the slab is 2 kN/m
2
07
FirstRanker.com - FirstRanker's Choice
Seat No.: ________ Enrolment No.___________
GUJARAT TECHNOLOGICAL UNIVERSITY
BE - SEMESTER ?VI(NEW) ? EXAMINATION ? SUMMER 2019
Subject Code:2164001 Date:10/05/2019
Subject Name:Design of Concrete Structures
Time:10:30 AM TO 01:30 PM Total Marks: 70
Instructions:
1. Attempt all questions.
2. Make suitable assumptions wherever necessary.
3. Figures to the right indicate full marks.
4. Use of IS 456, IS 875 is allowed.
5. Draw neat and clean sketches.
MARKS
Q.1 (a) Write advantages of limit state method (LSM) over working stress
method (WSM) of structural design philosophy.
07
(b) Calculate moment carrying capacity of a rectangular beam with
250 mm ? 400 mm overall section and having Ast = 1800 mm
2
. Assume
effective cover provided is 40 mm at tension side. Adopt M 30 and
Fe 415 grade of materials.
07
Q.2 (a) Design a reinforced concrete rectangular beam section of size
300 mm ? 600 mm overall from architectural considerations. The beam
is subjected to design moment of resistance 300 kN.m. The effective
cover to reinforcement is taken as 50 mm. Adopt M 20 and Fe 415 grade
of materials.
07
(b) Design a T-beam section with a flange width of 1250 mm, a flange depth
of 100 mm, a web width of 250 mm and an effective depth of 500 mm,
which is subjected to a factored moment of 560 kN.m. The concrete mix
is to be used is of grade M 20 and steel is grade Fe 415.
07
OR
(b) Design a cantilever beam of effective span of 2 m to sustain the uniformly
distributed load of 20 kN/m. Use M 25 grade of concrete and Fe 415
grade of steel.
07
Q.3 (a) Design a shear reinforcement for a simply supported RC beam subjected
to U.D.L. of 25 kN/m over a span of 3.6 m and having cross section of
230 mm width and 450 mm overall depth is reinforced with
3 # 16 mm ? HYSD steel of grade Fe 415, placed at an effective cover
of 50 mm. Use grade of concrete M 20.
07
(b) Design a slab over a room 4 m ? 5 m as per IS code. The slab is supported
on masonry walls all round with adequate restraint and the corners are
held down. The live load on the slab is 3 kN/m
2
. The slab has a bearing
of 150 mm on the supporting walls. Check for limit state of
serviceability.
07
OR
Q.3 (a) A simply supported RC beam of size 350 mm ? 550 mm overall is
reinforced with 3#20 mm ? of Fe 415 grade of steel. Determine the
anchorage length of the bars at the simply supported end if it is subjected
to a factored shear force of 350 kN at the centre of 300 mm wide masonry
support. The concrete mix of grade M 20 is to be used.
07
(b) Design one way simply supported slab of 9 m ? 4 m clear dimension, the
width of the support being 300 mm. The live load on the slab is 2 kN/m
2
07
and floor finish load is 1 kN/m
2
. Use M 20 grade of concrete and Fe 415
grade steel. Check for limit state of serviceability.
Q.4 (a) Design a dog legged staircase in a residential building with clear
dimensions of staircase area as 3150 mm ? 5250 mm. Floor to floor
height is 3.2 m. Use M 25 grade of concrete and Fe 415 of steel.
(Take Riser = 160 mm and Tread = 250 mm).
07
(b) A R.C. short column square in section has to resist a factored axial load
of 2000 kN. Consider 2 % of longitudinal reinforcement. Adopt M 30
grade of concrete and Fe 415 grade of steel.
Determine:
(i) Size of column
(ii) Area of longitudinal reinforcement
(iii) Pitch and diameter of lateral ties.
07
OR
Q.4 (a) Design a single flight staircase in a residential building, having floor
height of 3.2 m. Staircase is supported at top and bottom riser by beam
having width 300 mm. Consider Thickness of waist slab is 150 mm, riser
is 160 mm and tread is 300 mm. Use M 25 grade of concrete and Fe 415
grade of steel.
Evaluate :
(a) The effective span
(b) Design load
(c) Reinforcement in waist slab.
(d) Prepare a detail sketch of staircase.
07
(b) Design a short circular R.C.C. column to carry an axial load of
2000 kN. Use M 35 grade concrete and Fe 415 grade steel.
07
Q.5 (a) Design an isolated pad footing for a square R.C.C. column of size
600 mm ? 600 mm carrying axial load of 2000 kN. Safe bearing capacity
of soil is 200 kN/mm
2
. Use M 20 grade concrete and Fe 415 as steel
reinforcement. Effective cover for the bottom steel is 60 mm. Check for
shear is not required.
07
(b) A basement wall of height 3.75 m above the basement floor slab to soffit
of ground floor beam retains soil to its full height. The exterior face of
the wall is on the property line. The unit weight of soil and its angle of
repose are 19.5 kN/m
3
and 30
0
, respectively. The safe bearing capacity
of soil is 150 kN.m
2
. Design the basement wall using M 20 grade of
concrete and HYSD steel of grade Fe 415.
07
OR
Q.5 (a) Design a combined rectangular footing for axially loaded columns,
which carries 750 kN and 1000 kN loads spaced apart at 4 m center to
center. Each columns having size 350 mm ? 350 mm. Safe bearing
capacity of soil is 300 kN/m
2
. Use M 20 grade of concrete and Fe 415
grade of steel.
07
(b) Design a cantilever retaining wall (T type) to retain earth for a height of
4 m. The backfill is horizontal. The density of soil is 18 kN/m
3
. Safe
bearing capacity of soil is 180 kN/m
2
. Take the coefficient of friction
between concrete and soil as 0.6. The angle of repose is 30?. Use M 25
grade of concrete and Fe 415 grade of steel.
07
FirstRanker.com - FirstRanker's Choice
Seat No.: ________ Enrolment No.___________
GUJARAT TECHNOLOGICAL UNIVERSITY
BE - SEMESTER ?VI(NEW) ? EXAMINATION ? SUMMER 2019
Subject Code:2164001 Date:10/05/2019
Subject Name:Design of Concrete Structures
Time:10:30 AM TO 01:30 PM Total Marks: 70
Instructions:
1. Attempt all questions.
2. Make suitable assumptions wherever necessary.
3. Figures to the right indicate full marks.
4. Use of IS 456, IS 875 is allowed.
5. Draw neat and clean sketches.
MARKS
Q.1 (a) Write advantages of limit state method (LSM) over working stress
method (WSM) of structural design philosophy.
07
(b) Calculate moment carrying capacity of a rectangular beam with
250 mm ? 400 mm overall section and having Ast = 1800 mm
2
. Assume
effective cover provided is 40 mm at tension side. Adopt M 30 and
Fe 415 grade of materials.
07
Q.2 (a) Design a reinforced concrete rectangular beam section of size
300 mm ? 600 mm overall from architectural considerations. The beam
is subjected to design moment of resistance 300 kN.m. The effective
cover to reinforcement is taken as 50 mm. Adopt M 20 and Fe 415 grade
of materials.
07
(b) Design a T-beam section with a flange width of 1250 mm, a flange depth
of 100 mm, a web width of 250 mm and an effective depth of 500 mm,
which is subjected to a factored moment of 560 kN.m. The concrete mix
is to be used is of grade M 20 and steel is grade Fe 415.
07
OR
(b) Design a cantilever beam of effective span of 2 m to sustain the uniformly
distributed load of 20 kN/m. Use M 25 grade of concrete and Fe 415
grade of steel.
07
Q.3 (a) Design a shear reinforcement for a simply supported RC beam subjected
to U.D.L. of 25 kN/m over a span of 3.6 m and having cross section of
230 mm width and 450 mm overall depth is reinforced with
3 # 16 mm ? HYSD steel of grade Fe 415, placed at an effective cover
of 50 mm. Use grade of concrete M 20.
07
(b) Design a slab over a room 4 m ? 5 m as per IS code. The slab is supported
on masonry walls all round with adequate restraint and the corners are
held down. The live load on the slab is 3 kN/m
2
. The slab has a bearing
of 150 mm on the supporting walls. Check for limit state of
serviceability.
07
OR
Q.3 (a) A simply supported RC beam of size 350 mm ? 550 mm overall is
reinforced with 3#20 mm ? of Fe 415 grade of steel. Determine the
anchorage length of the bars at the simply supported end if it is subjected
to a factored shear force of 350 kN at the centre of 300 mm wide masonry
support. The concrete mix of grade M 20 is to be used.
07
(b) Design one way simply supported slab of 9 m ? 4 m clear dimension, the
width of the support being 300 mm. The live load on the slab is 2 kN/m
2
07
and floor finish load is 1 kN/m
2
. Use M 20 grade of concrete and Fe 415
grade steel. Check for limit state of serviceability.
Q.4 (a) Design a dog legged staircase in a residential building with clear
dimensions of staircase area as 3150 mm ? 5250 mm. Floor to floor
height is 3.2 m. Use M 25 grade of concrete and Fe 415 of steel.
(Take Riser = 160 mm and Tread = 250 mm).
07
(b) A R.C. short column square in section has to resist a factored axial load
of 2000 kN. Consider 2 % of longitudinal reinforcement. Adopt M 30
grade of concrete and Fe 415 grade of steel.
Determine:
(i) Size of column
(ii) Area of longitudinal reinforcement
(iii) Pitch and diameter of lateral ties.
07
OR
Q.4 (a) Design a single flight staircase in a residential building, having floor
height of 3.2 m. Staircase is supported at top and bottom riser by beam
having width 300 mm. Consider Thickness of waist slab is 150 mm, riser
is 160 mm and tread is 300 mm. Use M 25 grade of concrete and Fe 415
grade of steel.
Evaluate :
(a) The effective span
(b) Design load
(c) Reinforcement in waist slab.
(d) Prepare a detail sketch of staircase.
07
(b) Design a short circular R.C.C. column to carry an axial load of
2000 kN. Use M 35 grade concrete and Fe 415 grade steel.
07
Q.5 (a) Design an isolated pad footing for a square R.C.C. column of size
600 mm ? 600 mm carrying axial load of 2000 kN. Safe bearing capacity
of soil is 200 kN/mm
2
. Use M 20 grade concrete and Fe 415 as steel
reinforcement. Effective cover for the bottom steel is 60 mm. Check for
shear is not required.
07
(b) A basement wall of height 3.75 m above the basement floor slab to soffit
of ground floor beam retains soil to its full height. The exterior face of
the wall is on the property line. The unit weight of soil and its angle of
repose are 19.5 kN/m
3
and 30
0
, respectively. The safe bearing capacity
of soil is 150 kN.m
2
. Design the basement wall using M 20 grade of
concrete and HYSD steel of grade Fe 415.
07
OR
Q.5 (a) Design a combined rectangular footing for axially loaded columns,
which carries 750 kN and 1000 kN loads spaced apart at 4 m center to
center. Each columns having size 350 mm ? 350 mm. Safe bearing
capacity of soil is 300 kN/m
2
. Use M 20 grade of concrete and Fe 415
grade of steel.
07
(b) Design a cantilever retaining wall (T type) to retain earth for a height of
4 m. The backfill is horizontal. The density of soil is 18 kN/m
3
. Safe
bearing capacity of soil is 180 kN/m
2
. Take the coefficient of friction
between concrete and soil as 0.6. The angle of repose is 30?. Use M 25
grade of concrete and Fe 415 grade of steel.
07
[Reference: TABLE E, SP16, PG. 10]
[Reference: TABLE F, SP16, PG. 13]
***********
FirstRanker.com - FirstRanker's Choice
This post was last modified on 20 February 2020