This download link is referred from the post: GTU BE/B.Tech 2018 Winter Question Papers || Gujarat Technological University
GUJARAT TECHNOLOGICAL UNIVERSITY
BE - SEMESTER-VII (NEW) EXAMINATION - WINTER 2018
--- Content provided by FirstRanker.com ---
Subject Code: 2173203 Date: 15/11/2018Subject Name: Microprocessor and Microcontroller
Time: 10:30 AM TO 01:00 PM Total Marks: 70
Instructions:
- Attempt all questions.
- Make suitable assumptions wherever necessary.
- Figures to the right indicate full marks.
--- Content provided by FirstRanker.com ---
MARKS
Q.1 (a) Write a short note on microprocessors. 03
(b) Discuss AVR flag register in detail. 04
--- Content provided by FirstRanker.com ---
(c) Explain the Pin Diagram of the 8085 microprocessor. 07Q.2 (a) Explain PORT A functionality of ATMEGA32. 03
(b) How Microcontrollers are differing than Microprocessor? 04
(c) Explain Harvard architecture of AVR controller. 07
OR
--- Content provided by FirstRanker.com ---
(c) Explain architecture of the 8051 microcontroller. 07Q.3 (a) Explain the following instruction with example. 03
1.ORI 32H 2.INXD 3.SBBB.
(b) Explain Generation of the Control signal of the 8085 microprocessor. 04
(c) Write a short note on AVR Family 07
--- Content provided by FirstRanker.com ---
ORQ.3 (a) Compare RISC and CISC. 03
(b) Design a microprocessor memory interfacing system for 8Kbyte 04
RAM with starting address 0000H.Immediately connect 4Kbyte
EEPROM.
--- Content provided by FirstRanker.com ---
(c) A switch is connected to pin PB2.-Write a program to monitor the status 07of the SW and perform the following.
1. If SW =0, send the letter Nā to PORT D.
2. If SW =1, send the letter Yā to PORT D.
Q.4 (a) Explain rotate instructions of AVR controller with example. 03
--- Content provided by FirstRanker.com ---
(b) Explain different steps for executing an interrupt. 04(c) Write an assembly program to toggle only the PORT B. 4 bit 07
continuously every 70ps. Use Timer 0, Normal mode and 1:8
prescaler to create the delay. Assume XTAL=8MHz.
OR
--- Content provided by FirstRanker.com ---
Q.4 (a) What is the role of DDR register in inputting data for AVR 03Controller?
(b) Write an AVR C program to toggle all the pins of Port B 04
continuously by using the Ex-OR operator.
(c) Explain the addressing mode for the AVR Controller. 07
--- Content provided by FirstRanker.com ---
Q.5 (a) Give comparison serial versus parallel data transfer. 03
(b) Write a short note on AVR Data type. 04
(c) Write program to read key-press event and display key-code on LEDs 07
connected at port PO.
OR
--- Content provided by FirstRanker.com ---
Q.5 (a) With Fosc =8 MHz, Find the UBRR value needed to have the following 03baud rates.
1.9600 2.4800 3.2400
(b) Write an assembly program for the AVR to transfer the letter āGā 04
serially at 9600 baud, continuously. Use 8-bit data and 1 stop bit.
--- Content provided by FirstRanker.com ---
Assume XTAL=8MHz.(c) Explain I2C Bus protocol. 07
--- Content provided by FirstRanker.com ---
This download link is referred from the post: GTU BE/B.Tech 2018 Winter Question Papers || Gujarat Technological University