Download PTU B.Tech 2020 March ECE 4th Sem BTEC 404 Electronic Measurement & Instrumentation Question Paper

Download PTU (I.K. Gujral Punjab Technical University Jalandhar (IKGPTU) ) BE/BTech ECE (Electronics And Communications Engineering) 2020 March 4th Sem BTEC 404 Electronic Measurement & Instrumentation Previous Question Paper

1 | M - 5 7 5 9 6 ( S 2 ) - 2 1 6 6

Roll No. Total No. of Pages : 02
Total No. of Questions : 09

B.Tech. (ECE) (2012 to 2017) (Sem.?4)
ELECTRONIC MEASUREMENT & INSTRUMENTATION
Subject Code : BTEC-404
M.Code : 57596
Time : 3 Hrs. Max. Marks : 60
INSTRUCTIONS TO CANDIDATES :
1. SECTION-A is COMPULSORY consisting of TEN questions carrying TWO marks
each.
2. SECTION-B contains FIVE questions carrying FIVE marks each and students
have to attempt any FOUR questions.
3. SECTION-C contains THREE questions carrying TEN marks each and students
have to attempt any TWO questions.

SECTION-A
Q1. Answer briefy :
a) List out the dynamic characteristics of any measurement system.
b) What are the types of error measurement system?
c) What is calibration?
d) Explain why it is necessary to make the potential coil circuit purely resistive in watt-
meters.
e) What is creeping and how it is prevented?
f) Why the PMMC instrument is not used for a.c measurements?
g) Compare Hay?s bridge with Maxwell bridge.
h) Write the application of d.c. Potentiometer.
i) What are the different types of amplifiers used for CRO?s?
j) Define Gauge Factor.
FirstRanker.com - FirstRanker's Choice
1 | M - 5 7 5 9 6 ( S 2 ) - 2 1 6 6

Roll No. Total No. of Pages : 02
Total No. of Questions : 09

B.Tech. (ECE) (2012 to 2017) (Sem.?4)
ELECTRONIC MEASUREMENT & INSTRUMENTATION
Subject Code : BTEC-404
M.Code : 57596
Time : 3 Hrs. Max. Marks : 60
INSTRUCTIONS TO CANDIDATES :
1. SECTION-A is COMPULSORY consisting of TEN questions carrying TWO marks
each.
2. SECTION-B contains FIVE questions carrying FIVE marks each and students
have to attempt any FOUR questions.
3. SECTION-C contains THREE questions carrying TEN marks each and students
have to attempt any TWO questions.

SECTION-A
Q1. Answer briefy :
a) List out the dynamic characteristics of any measurement system.
b) What are the types of error measurement system?
c) What is calibration?
d) Explain why it is necessary to make the potential coil circuit purely resistive in watt-
meters.
e) What is creeping and how it is prevented?
f) Why the PMMC instrument is not used for a.c measurements?
g) Compare Hay?s bridge with Maxwell bridge.
h) Write the application of d.c. Potentiometer.
i) What are the different types of amplifiers used for CRO?s?
j) Define Gauge Factor.
2 | M - 5 7 5 9 6 ( S 2 ) - 2 1 6 6

SECTION-B
Q2) Discuss R-2R ladder type DAC.
Q3) Explain in detail about ADC and DAC converters.
Q4) Describe the principle of working and circuit diagram of a digital oscilloscope.
Q5) Derive the bridge balance condition for the Maxwell Bridge and Schering Bridge.
Q6) Derive the torque equation of electrodynamometer type instrument.

SECTION-C
Q7) What is telemetry system and explain its types in detail.
Q8) Explain the construction and principle of working of a LVDT.
Q9) Two watt meters are connected to measure the input to a balanced 3phase circuit indicate
2000 W and 500 W respectively. Find the power factor of the Circuit (1) when both the
readings are positive (2) when the latter reading is obtained after reversing the connection
to the current coil of first instrument.









NOTE : Disclosure of Identity by writing Mobile No. or Making of passing request on any
page of Answer Sheet will lead to UMC against the Student.
FirstRanker.com - FirstRanker's Choice