Download PTU (I.K. Gujral Punjab Technical University Jalandhar (IKGPTU) ) BE/BTech ECE (Electronics And Communications Engineering) 2020 March 6th Sem BTEC 903 Industrial Electronics Previous Question Paper
Roll No. Total No. of Pages : 02
Total No. of Questions : 09
B.Tech.(ECE) (E-I 2012 to 2017) (Sem.?6)
INDUSTRIAL ELECTRONICS
Subject Code : BTEC-903
M.Code : 71232
Time : 3 Hrs. Max. Marks : 60
INSTRUCTIONS TO CANDIDATES :
1. SECTION-A is COMPULSORY consisting of TEN questions carrying TWO marks
each.
2. SECTION-B contains FIVE questions carrying FIVE marks each and students
have to attempt any FOUR questions.
3. SECTION-C contains THREE questions carrying TEN marks each and students
have to attempt any TWO questions.
SECTION-A
1. Answer briefly :
a) What is the need of commutation process?
b) What is the function of freewheeling diode?
c) Discuss the need of equalization in parallel connections of SCRs.
d) Discuss the significance of ON and OFF cycles in integral cycle control.
e) What is finger voltage?
f) Define total harmonic distortion.
g) Discuss time ratio control in choppers.
h) What is forced commutated inverters?
i) Why protection against dv/dt is necessary?
j) What is the function of crowbar circuit?
FirstRanker.com - FirstRanker's Choice
1 | M-71232 (S2)-2113
Roll No. Total No. of Pages : 02
Total No. of Questions : 09
B.Tech.(ECE) (E-I 2012 to 2017) (Sem.?6)
INDUSTRIAL ELECTRONICS
Subject Code : BTEC-903
M.Code : 71232
Time : 3 Hrs. Max. Marks : 60
INSTRUCTIONS TO CANDIDATES :
1. SECTION-A is COMPULSORY consisting of TEN questions carrying TWO marks
each.
2. SECTION-B contains FIVE questions carrying FIVE marks each and students
have to attempt any FOUR questions.
3. SECTION-C contains THREE questions carrying TEN marks each and students
have to attempt any TWO questions.
SECTION-A
1. Answer briefly :
a) What is the need of commutation process?
b) What is the function of freewheeling diode?
c) Discuss the need of equalization in parallel connections of SCRs.
d) Discuss the significance of ON and OFF cycles in integral cycle control.
e) What is finger voltage?
f) Define total harmonic distortion.
g) Discuss time ratio control in choppers.
h) What is forced commutated inverters?
i) Why protection against dv/dt is necessary?
j) What is the function of crowbar circuit?
2 | M-71232 (S2)-2113
SECTION-B
2. Draw and explain the static and dynamic characteristics of SCRs.
3. Describe the basic principle of working of single phase to single phase stepdown
cycloconverter for both continuous and discontinuous conductions for bridge type
cycloconverter.
4. What is the need of series connections of SCRs? Explain series operation of SCR's and
equalization circuits with suitable circuits.
5. Explain resistance-triggering & RC- triggering circuit for a thyristor.
6. What is the need of chopper? A dc chopper has an input voltage of 230 V and an output
voltage of 150 V. It is operating at a frequency of 1 kHz. Find the periods of conduction
and blocking in each cycle.
SECTION-C
7. Explain the circuit of the single-phase fully controlled bridge rectifier with RL load and
with freewheeling diode. Also draw the waveforms.
8. Describe the working of a single-phase half bridge inverter. What is its main drawback?
How can this drawback be overcome?
9. a) Describe the working of single phase half wave converter feeding a separately excited
DC motor with suitable circuits and waveforms.
b) Describe the principle of phase control in single phase half wave AC voltage
controller. Derive the expression for rms value of output voltage.
NOTE : Disclosure of Identity by writing Mobile No. or Making of passing request on any
page of Answer Sheet will lead to UMC against the Student.
FirstRanker.com - FirstRanker's Choice
This post was last modified on 21 March 2020