Download AKTU B-Tech 4th Sem 2017-18 REC405 Introduction To Microprocessors Question Paper

Download AKTU (Dr. A.P.J. Abdul Kalam Technical University (AKTU), formerly Uttar Pradesh Technical University (UPTU)) B-Tech 4th Semester (Fourth Semester) 2017-18 REC405 Introduction To Microprocessors Question Paper

Printed Pages: 02 Sub Code: REC405

Paper Id: 131414 Roll No.

B. Tech.
(SEM IV) THEORY EXAMINATION 2017-18
INTRODUCTION TO MICROPROCESSORS
Time: 3 Hours Total Marks: 70
Note: 1. Attempt all Sections. If require any missing data; then choose suitably.

SECTION A
1. Attempt all questions in brief. 2 x 7 = 14
a) Describe the logic devices for interfacing.
b) Describe the function of ALE signal.
c) Explain the programming techniques of Looping and Counting.
d) Explain the difference between RLC and RAL.
e) What is a subroutine? Explain the concept of multiple calling for a subroutine.
f) List the various modes of 8254/ 8253 programmable interval timer IC.
g) Explain the function of DMA controller.
SECTION B
2. Attempt any three of the following: 7 x 3 = 21
a) Draw the block diagram of 8085 microprocessor and explain its various blocks and
signals. Explain the programming model of 8085. Explain the flag register bits.
b) Describe the concept interfacing input and output devices with 8085 microprocessor
by interfacing 8-DIP switches as input devices and Seven-segment LED display as
output device to 8085.
c) Describe the various Interrupts of 8085 microprocessor. What are vectored interrupts?
Describe the vector address of 8085 interrupts.
d) Explain the concept of BCD addition using a suitable example. Write a assembly level
program for the addition of two unsigned BCD numbers.
e) Explain the function of Programmable peripheral interface IC 8255 with the help of a
block diagram. Describe the Ports of IC8255 with their available modes of operation.

SECTION C
3. Attempt any one part of the following: 7 x 1 = 7
(a) Explain how the op-code is fetched from the memory. Explain the op-code fetch
cycle with the help of a timing diagram
(b) Differentiate between absolute decoding and partial decoding schemes of address
decoding. Design a scheme to generate Read/Write control signals for memory and
I/O from microprocessor signals IO/M?, RD?, WR?.
4. Attempt any one part of the following: 7 x 1 = 7
(a) (i)The memory location 2050H holds the data byte F7h. Write instructions to transfer
the data byte to the accumulator using thee different opcodes: MOV, LDAX, and
LDA.
(ii) Explain the various addressing modes of 8085 with suitable examples.
FirstRanker.com - FirstRanker's Choice
Printed Pages: 02 Sub Code: REC405

Paper Id: 131414 Roll No.

B. Tech.
(SEM IV) THEORY EXAMINATION 2017-18
INTRODUCTION TO MICROPROCESSORS
Time: 3 Hours Total Marks: 70
Note: 1. Attempt all Sections. If require any missing data; then choose suitably.

SECTION A
1. Attempt all questions in brief. 2 x 7 = 14
a) Describe the logic devices for interfacing.
b) Describe the function of ALE signal.
c) Explain the programming techniques of Looping and Counting.
d) Explain the difference between RLC and RAL.
e) What is a subroutine? Explain the concept of multiple calling for a subroutine.
f) List the various modes of 8254/ 8253 programmable interval timer IC.
g) Explain the function of DMA controller.
SECTION B
2. Attempt any three of the following: 7 x 3 = 21
a) Draw the block diagram of 8085 microprocessor and explain its various blocks and
signals. Explain the programming model of 8085. Explain the flag register bits.
b) Describe the concept interfacing input and output devices with 8085 microprocessor
by interfacing 8-DIP switches as input devices and Seven-segment LED display as
output device to 8085.
c) Describe the various Interrupts of 8085 microprocessor. What are vectored interrupts?
Describe the vector address of 8085 interrupts.
d) Explain the concept of BCD addition using a suitable example. Write a assembly level
program for the addition of two unsigned BCD numbers.
e) Explain the function of Programmable peripheral interface IC 8255 with the help of a
block diagram. Describe the Ports of IC8255 with their available modes of operation.

SECTION C
3. Attempt any one part of the following: 7 x 1 = 7
(a) Explain how the op-code is fetched from the memory. Explain the op-code fetch
cycle with the help of a timing diagram
(b) Differentiate between absolute decoding and partial decoding schemes of address
decoding. Design a scheme to generate Read/Write control signals for memory and
I/O from microprocessor signals IO/M?, RD?, WR?.
4. Attempt any one part of the following: 7 x 1 = 7
(a) (i)The memory location 2050H holds the data byte F7h. Write instructions to transfer
the data byte to the accumulator using thee different opcodes: MOV, LDAX, and
LDA.
(ii) Explain the various addressing modes of 8085 with suitable examples.
(b) Classify the instruction set of 8085 on the basis of their functions. Write the different
instructions and explain their function.
5. Attempt any one part of the following: 7 x 1 = 7
(a) Draw the flowchart and write a program and for a zero-to-nine (module ten) counter.
(b) Explain the concept of stack memory and stack pointer. Describe the various
conditional call and conditional return instructions.

6. Attempt any one part of the following: 7 x 1 = 7
(a) A multiplicand is stored in memory location 2050H and a multiplier is stored in the
location 2051H. Write a main program to transfer the two numbers from memory
locations to the HL registers and store the product in the output buffer at 2090H.
Write a subroutine to multiply two unsigned numbers placed in registers H and L and
return the result in to the HL pair
(b) (i) Explain the function of instructions: XCHG, XTHL, SHLD, and SPHL.
(ii) Registers BC contain 8538H and registers DE contain 62A5H. Write instructions
to subtract the contents of DE from the contents of BC and place the result in BC.
7. Attempt any one part of the following: 7 x 1 = 7
(a) Describe the block diagram of 8259A programmable interrupt controller and explain
each block. Describe the priority modes of the 8259.
(b) Describe the function of BIU and EU in the architecture of 8086 microprocessor.
Explain the Register organization of 8086 microprocessor. Explain the function of
signals: TEST?, LOCK?.

FirstRanker.com - FirstRanker's Choice

This post was last modified on 29 January 2020