Download JNTUK (Jawaharlal Nehru Technological University Kakinada) B.Tech Regular 2014 Feb-March I Semester (1st Year 1st Sem) ENGINEERING CHEMISTRY Question Paper.
I B. Tech I Semester Regular Examinations Feb./Mar. - 2014
ENGINEERING CHEMISTRY
(Common to CE,ME,CSE,PCE,IT,Chem E,Aero E,AME,Min E,PE,Metal E)
Time: 3 hours Max. Marks: 70
Question Paper Consists of Part-A and Part-B
Answering the question in Part-A is Compulsory,
Three Questions should be answered from Part-B
*****
PART-A
1.(a) Discuss (i) p-type doped conducting polymers (ii) phosphate conditioning
(iii) antiknocking agents
(b) Write a note on protection (against corrosion) of a metal by metallic coatings.
(c) A 0.1 M KCl solution, whose specific conductance is 0.01571 mho cm
-1
, has a
conductance of 0.014 mho. When the same conductivity cell is used a 0.1 M chloroacetic
acid solution has a conductance of 7.84 x 10
-3
mho. If the ionic conductance of
ClCH
2
COO
-
and H
+
are 59.8 and 449.8 mhocm
2
equiv.
-1
, find the degree of dissociation
of chloroacetic acid.
[12+4+6]
PART-B
2.(a) Describe cold and hot lime soda processes with a neat diagram.
(b) A sample of water on analysis has been found to contain the following in ppm:
Ca (HCO
3
)
2
= 4.86; Mg (HCO
3
)
2
= 5.84, CaSO
4
= 6.8, MgSO
4
= 8.4. Calculate the
temporary and permanent hardness of water.
(c) Discuss (i) stereospecific polymers (ii) mechanical properties of polymers
[6+4+6]
3.(a) What is ion-selective electrode? Explain its working.
(b) Discuss potentiometric titrations.
(c) Write notes on (i) Refining of petrol (ii) reforming
[6+4+6]
4.(a) Explain the factors effecting the rate of corrosion.
(b) Write notes on Electroplating
(c) Discuss (i) bullet proof plastics (ii) green house effects
[6+4+6]
5.(a) Explain compounding and vulcanization of rubber.
(b) What is copolymerization. Give any two examples.
(c) Write notes on (i) caustic embrittlement (ii) galvanizing
[7+3+6]
6.(a) Write notes on (i) LPG (ii) diesel knocking (iii) Ni-Cd battery
(b) A sample of coal was found to contain the following constituents: C = 81%; O=7%;
S=2%; N=5.5% and ash=4.5%. Calculate the minimum amount of air required for
complete combustion of 1 kg of coal.
(c) Explain break-point chlorination of water.
[9+4+3]
7.(a) Write any four applications of carbon nanotubes.
(b) Explain the working of photovoltaic cells with a neat sketch.
(c) Write notes on (ii) Impressed current cathodic protection (ii) galvanic cell
[5+5+6]
Page 1 of 1
Set No - 1
FirstRanker.com - FirstRanker's Choice
Subject Code: R13104/R13
I B. Tech I Semester Regular Examinations Feb./Mar. - 2014
ENGINEERING CHEMISTRY
(Common to CE,ME,CSE,PCE,IT,Chem E,Aero E,AME,Min E,PE,Metal E)
Time: 3 hours Max. Marks: 70
Question Paper Consists of Part-A and Part-B
Answering the question in Part-A is Compulsory,
Three Questions should be answered from Part-B
*****
PART-A
1.(a) Discuss (i) p-type doped conducting polymers (ii) phosphate conditioning
(iii) antiknocking agents
(b) Write a note on protection (against corrosion) of a metal by metallic coatings.
(c) A 0.1 M KCl solution, whose specific conductance is 0.01571 mho cm
-1
, has a
conductance of 0.014 mho. When the same conductivity cell is used a 0.1 M chloroacetic
acid solution has a conductance of 7.84 x 10
-3
mho. If the ionic conductance of
ClCH
2
COO
-
and H
+
are 59.8 and 449.8 mhocm
2
equiv.
-1
, find the degree of dissociation
of chloroacetic acid.
[12+4+6]
PART-B
2.(a) Describe cold and hot lime soda processes with a neat diagram.
(b) A sample of water on analysis has been found to contain the following in ppm:
Ca (HCO
3
)
2
= 4.86; Mg (HCO
3
)
2
= 5.84, CaSO
4
= 6.8, MgSO
4
= 8.4. Calculate the
temporary and permanent hardness of water.
(c) Discuss (i) stereospecific polymers (ii) mechanical properties of polymers
[6+4+6]
3.(a) What is ion-selective electrode? Explain its working.
(b) Discuss potentiometric titrations.
(c) Write notes on (i) Refining of petrol (ii) reforming
[6+4+6]
4.(a) Explain the factors effecting the rate of corrosion.
(b) Write notes on Electroplating
(c) Discuss (i) bullet proof plastics (ii) green house effects
[6+4+6]
5.(a) Explain compounding and vulcanization of rubber.
(b) What is copolymerization. Give any two examples.
(c) Write notes on (i) caustic embrittlement (ii) galvanizing
[7+3+6]
6.(a) Write notes on (i) LPG (ii) diesel knocking (iii) Ni-Cd battery
(b) A sample of coal was found to contain the following constituents: C = 81%; O=7%;
S=2%; N=5.5% and ash=4.5%. Calculate the minimum amount of air required for
complete combustion of 1 kg of coal.
(c) Explain break-point chlorination of water.
[9+4+3]
7.(a) Write any four applications of carbon nanotubes.
(b) Explain the working of photovoltaic cells with a neat sketch.
(c) Write notes on (ii) Impressed current cathodic protection (ii) galvanic cell
[5+5+6]
Page 1 of 1
Set No - 1
Subject Code: R13104/R13
I B. Tech I Semester Regular Examinations Feb./Mar. - 2014
ENGINEERING CHEMISTRY
(Common to CE,ME,CSE,PCE,IT,Chem E,Aero E,AME,Min E,PE,Metal E)
Time: 3 hours Max. Marks: 70
Question Paper Consists of Part-A and Part-B
Answering the question in Part-A is Compulsory,
Three Questions should be answered from Part-B
*****
PART-A
1.(a) Name the various fractions obtained during fractional distillation of crude oil and indicate
their boiling point ranges and uses of various fractions.
(b) The ion conductance of H
+
and butyrate ions are 339.8 and 30.6 Scm
2
equiv
-1
respectively. When same conductance cell is employed 0.1 M KCl and 0.1 M butyric
acid recorded conductances of 1.3 x 10
-2
and 5.25 x 10
-4
Scm
2
respectively . If the
conductivity of the above KCl solution is 0.0121 S cm
-1
, calculate the degree of
dissociation of butyric acid.
(c) Write notes on (i) turbine deposits (ii) Anodized coatings (iii) Solar reflectors
[6+7+9]
PART-B
2.(a) Describe (i) zeolite process (ii) Priming and foaming
(b) Calculate the amount of lime and soda required for the softening of 150 liters of water,
which is analyzed as: temporary hardness = 20 ppm; permanent hardness = 15 ppm;
permanent Mg hardness = 10 ppm.
(c) Discuss the preparation of Bakelite and Thiokol and mention their uses.
[6+4+6]
3.(a) Explain with neat diagrams the working of (i) glass electrode (ii) concentration cell
(iii) Lechlanche cell
(b) Describe any one method of catalytic cracking process for obtaining gasoline.
[10+6]
4.(a) Explain electrochemical corrosion.
(b) Explain galvanizing and tinning.
(c) Describe any two methods of synthesis in green chemistry.
[6+4+6]
5.(a) Describe with neat sketches, any two moulding techniques of plastics.
(b) What are the drawbacks of natural rubber.
(c) What are the different constituents of paints and give their function.
(d) Write notes on caustic embrittlement.
[6+4+3+3]
6.(a) Define calorific value, HCV and LCV. Calculate the gross and net calorific value of coal
having the following compositions C = 83%; H = 10%; S = 1%, N = 3%, Ash = 3%.
Latent heat of steam = 587 cal/g.
(b) Discuss (i) applications of Kohlrausch law (ii) scales and sludges
[10+6]
7.(a) Write notes on (i) deterioration of cement concrete (ii) Types of Liquid crystals (iii) Need
of green chemistry
(b) Explain (i) electrochemical cell (ii) metal cladding
[10+6]
Page 1 of 1
Set No - 2
FirstRanker.com - FirstRanker's Choice
Subject Code: R13104/R13
I B. Tech I Semester Regular Examinations Feb./Mar. - 2014
ENGINEERING CHEMISTRY
(Common to CE,ME,CSE,PCE,IT,Chem E,Aero E,AME,Min E,PE,Metal E)
Time: 3 hours Max. Marks: 70
Question Paper Consists of Part-A and Part-B
Answering the question in Part-A is Compulsory,
Three Questions should be answered from Part-B
*****
PART-A
1.(a) Discuss (i) p-type doped conducting polymers (ii) phosphate conditioning
(iii) antiknocking agents
(b) Write a note on protection (against corrosion) of a metal by metallic coatings.
(c) A 0.1 M KCl solution, whose specific conductance is 0.01571 mho cm
-1
, has a
conductance of 0.014 mho. When the same conductivity cell is used a 0.1 M chloroacetic
acid solution has a conductance of 7.84 x 10
-3
mho. If the ionic conductance of
ClCH
2
COO
-
and H
+
are 59.8 and 449.8 mhocm
2
equiv.
-1
, find the degree of dissociation
of chloroacetic acid.
[12+4+6]
PART-B
2.(a) Describe cold and hot lime soda processes with a neat diagram.
(b) A sample of water on analysis has been found to contain the following in ppm:
Ca (HCO
3
)
2
= 4.86; Mg (HCO
3
)
2
= 5.84, CaSO
4
= 6.8, MgSO
4
= 8.4. Calculate the
temporary and permanent hardness of water.
(c) Discuss (i) stereospecific polymers (ii) mechanical properties of polymers
[6+4+6]
3.(a) What is ion-selective electrode? Explain its working.
(b) Discuss potentiometric titrations.
(c) Write notes on (i) Refining of petrol (ii) reforming
[6+4+6]
4.(a) Explain the factors effecting the rate of corrosion.
(b) Write notes on Electroplating
(c) Discuss (i) bullet proof plastics (ii) green house effects
[6+4+6]
5.(a) Explain compounding and vulcanization of rubber.
(b) What is copolymerization. Give any two examples.
(c) Write notes on (i) caustic embrittlement (ii) galvanizing
[7+3+6]
6.(a) Write notes on (i) LPG (ii) diesel knocking (iii) Ni-Cd battery
(b) A sample of coal was found to contain the following constituents: C = 81%; O=7%;
S=2%; N=5.5% and ash=4.5%. Calculate the minimum amount of air required for
complete combustion of 1 kg of coal.
(c) Explain break-point chlorination of water.
[9+4+3]
7.(a) Write any four applications of carbon nanotubes.
(b) Explain the working of photovoltaic cells with a neat sketch.
(c) Write notes on (ii) Impressed current cathodic protection (ii) galvanic cell
[5+5+6]
Page 1 of 1
Set No - 1
Subject Code: R13104/R13
I B. Tech I Semester Regular Examinations Feb./Mar. - 2014
ENGINEERING CHEMISTRY
(Common to CE,ME,CSE,PCE,IT,Chem E,Aero E,AME,Min E,PE,Metal E)
Time: 3 hours Max. Marks: 70
Question Paper Consists of Part-A and Part-B
Answering the question in Part-A is Compulsory,
Three Questions should be answered from Part-B
*****
PART-A
1.(a) Name the various fractions obtained during fractional distillation of crude oil and indicate
their boiling point ranges and uses of various fractions.
(b) The ion conductance of H
+
and butyrate ions are 339.8 and 30.6 Scm
2
equiv
-1
respectively. When same conductance cell is employed 0.1 M KCl and 0.1 M butyric
acid recorded conductances of 1.3 x 10
-2
and 5.25 x 10
-4
Scm
2
respectively . If the
conductivity of the above KCl solution is 0.0121 S cm
-1
, calculate the degree of
dissociation of butyric acid.
(c) Write notes on (i) turbine deposits (ii) Anodized coatings (iii) Solar reflectors
[6+7+9]
PART-B
2.(a) Describe (i) zeolite process (ii) Priming and foaming
(b) Calculate the amount of lime and soda required for the softening of 150 liters of water,
which is analyzed as: temporary hardness = 20 ppm; permanent hardness = 15 ppm;
permanent Mg hardness = 10 ppm.
(c) Discuss the preparation of Bakelite and Thiokol and mention their uses.
[6+4+6]
3.(a) Explain with neat diagrams the working of (i) glass electrode (ii) concentration cell
(iii) Lechlanche cell
(b) Describe any one method of catalytic cracking process for obtaining gasoline.
[10+6]
4.(a) Explain electrochemical corrosion.
(b) Explain galvanizing and tinning.
(c) Describe any two methods of synthesis in green chemistry.
[6+4+6]
5.(a) Describe with neat sketches, any two moulding techniques of plastics.
(b) What are the drawbacks of natural rubber.
(c) What are the different constituents of paints and give their function.
(d) Write notes on caustic embrittlement.
[6+4+3+3]
6.(a) Define calorific value, HCV and LCV. Calculate the gross and net calorific value of coal
having the following compositions C = 83%; H = 10%; S = 1%, N = 3%, Ash = 3%.
Latent heat of steam = 587 cal/g.
(b) Discuss (i) applications of Kohlrausch law (ii) scales and sludges
[10+6]
7.(a) Write notes on (i) deterioration of cement concrete (ii) Types of Liquid crystals (iii) Need
of green chemistry
(b) Explain (i) electrochemical cell (ii) metal cladding
[10+6]
Page 1 of 1
Set No - 2
Subject Code: R13104/R13
I B. Tech I Semester Regular Examinations Feb./Mar. - 2014
ENGINEERING CHEMISTRY
(Common to CE,ME,CSE,PCE,IT,Chem E,Aero E,AME,Min E,PE,Metal E)
Time: 3 hours Max. Marks: 70
Question Paper Consists of Part-A and Part-B
Answering the question in Part-A is Compulsory,
Three Questions should be answered from Part-B
*****
PART-A
1.(a) Write notes on (ii) CNG (ii) properties of Thiokol (iii) phosphate coatings
(b) Explain the mechanism of setting and hardening of cement.
(c) Calculate the amount of lime (84% pure) and soda (92% pure) required for softening
10, 000 litres of water containing the following salts per litre:
Ca(HCO
3
)
2
= 40.5 mg; Mg(HCO
3
)
2
= 36.5 mg; MgSO
4
= 30 mg; CaSO
4
= 34 mg;
CaCl
2
= 27.75 mg and NaCl = 10 mg. Also calculate the temporary hardness and
permanent hardness of the water sample.
[7+6+9]
PART-B
2.(a) Describe with neat sketch ion exchange process of softening of water.
(b) Write notes on (i) scales and sludges (ii) tacticity
(c) What is condensation polymerization? Explain with example.
[6+8+2]
3.(a) Describe the construction and working of hydrogen-oxygen fuel cell.
(b) At 25
0
C, the equivalent conductivities at infinite dilution of HCl, CH
3
COONa and NaCl
are 428.03, 93.3, and 125.78 ohm
-1
cm
2
equiv
-1
respectively. Calculate the equivalent
conductance of acetic acid at infinite dilution
(c) Discuss the ultimate analysis of coal
[7+3+6]
4.(a) Discuss the mechanism of dry corrosion. Explain the role of oxide film in dry corrosion.
(b) Explain the importance of design and selection of materials in controlling corrosion.
(c) Describe any two preparation methods for carbon nanotubes with neat sketch diagrams.
[6+4+6]
5.(a) Explain free radical mechanism of addition polymerization.
(b) Write the preparation and uses of (i) PVC (ii) Bakelite
(c) Write notes on (i) Reverse Osmosis (ii) anodic and cathodic inhibitors
[4+6+6]
6. Write notes on (i) refining (ii) octane number (iii) antiknocking agents (iv) cold lime soda
process (v) calomel electrode
[16]
7.(a) Write any four applications of (i) green chemistry (ii) liquid crystals (iii) fullerenes
(b) Write notes on (i) drying, semidrying and nondrying oils (ii) Kohlrausch law
[10+6]
Page 1 of 1
Set No - 3
FirstRanker.com - FirstRanker's Choice
Subject Code: R13104/R13
I B. Tech I Semester Regular Examinations Feb./Mar. - 2014
ENGINEERING CHEMISTRY
(Common to CE,ME,CSE,PCE,IT,Chem E,Aero E,AME,Min E,PE,Metal E)
Time: 3 hours Max. Marks: 70
Question Paper Consists of Part-A and Part-B
Answering the question in Part-A is Compulsory,
Three Questions should be answered from Part-B
*****
PART-A
1.(a) Discuss (i) p-type doped conducting polymers (ii) phosphate conditioning
(iii) antiknocking agents
(b) Write a note on protection (against corrosion) of a metal by metallic coatings.
(c) A 0.1 M KCl solution, whose specific conductance is 0.01571 mho cm
-1
, has a
conductance of 0.014 mho. When the same conductivity cell is used a 0.1 M chloroacetic
acid solution has a conductance of 7.84 x 10
-3
mho. If the ionic conductance of
ClCH
2
COO
-
and H
+
are 59.8 and 449.8 mhocm
2
equiv.
-1
, find the degree of dissociation
of chloroacetic acid.
[12+4+6]
PART-B
2.(a) Describe cold and hot lime soda processes with a neat diagram.
(b) A sample of water on analysis has been found to contain the following in ppm:
Ca (HCO
3
)
2
= 4.86; Mg (HCO
3
)
2
= 5.84, CaSO
4
= 6.8, MgSO
4
= 8.4. Calculate the
temporary and permanent hardness of water.
(c) Discuss (i) stereospecific polymers (ii) mechanical properties of polymers
[6+4+6]
3.(a) What is ion-selective electrode? Explain its working.
(b) Discuss potentiometric titrations.
(c) Write notes on (i) Refining of petrol (ii) reforming
[6+4+6]
4.(a) Explain the factors effecting the rate of corrosion.
(b) Write notes on Electroplating
(c) Discuss (i) bullet proof plastics (ii) green house effects
[6+4+6]
5.(a) Explain compounding and vulcanization of rubber.
(b) What is copolymerization. Give any two examples.
(c) Write notes on (i) caustic embrittlement (ii) galvanizing
[7+3+6]
6.(a) Write notes on (i) LPG (ii) diesel knocking (iii) Ni-Cd battery
(b) A sample of coal was found to contain the following constituents: C = 81%; O=7%;
S=2%; N=5.5% and ash=4.5%. Calculate the minimum amount of air required for
complete combustion of 1 kg of coal.
(c) Explain break-point chlorination of water.
[9+4+3]
7.(a) Write any four applications of carbon nanotubes.
(b) Explain the working of photovoltaic cells with a neat sketch.
(c) Write notes on (ii) Impressed current cathodic protection (ii) galvanic cell
[5+5+6]
Page 1 of 1
Set No - 1
Subject Code: R13104/R13
I B. Tech I Semester Regular Examinations Feb./Mar. - 2014
ENGINEERING CHEMISTRY
(Common to CE,ME,CSE,PCE,IT,Chem E,Aero E,AME,Min E,PE,Metal E)
Time: 3 hours Max. Marks: 70
Question Paper Consists of Part-A and Part-B
Answering the question in Part-A is Compulsory,
Three Questions should be answered from Part-B
*****
PART-A
1.(a) Name the various fractions obtained during fractional distillation of crude oil and indicate
their boiling point ranges and uses of various fractions.
(b) The ion conductance of H
+
and butyrate ions are 339.8 and 30.6 Scm
2
equiv
-1
respectively. When same conductance cell is employed 0.1 M KCl and 0.1 M butyric
acid recorded conductances of 1.3 x 10
-2
and 5.25 x 10
-4
Scm
2
respectively . If the
conductivity of the above KCl solution is 0.0121 S cm
-1
, calculate the degree of
dissociation of butyric acid.
(c) Write notes on (i) turbine deposits (ii) Anodized coatings (iii) Solar reflectors
[6+7+9]
PART-B
2.(a) Describe (i) zeolite process (ii) Priming and foaming
(b) Calculate the amount of lime and soda required for the softening of 150 liters of water,
which is analyzed as: temporary hardness = 20 ppm; permanent hardness = 15 ppm;
permanent Mg hardness = 10 ppm.
(c) Discuss the preparation of Bakelite and Thiokol and mention their uses.
[6+4+6]
3.(a) Explain with neat diagrams the working of (i) glass electrode (ii) concentration cell
(iii) Lechlanche cell
(b) Describe any one method of catalytic cracking process for obtaining gasoline.
[10+6]
4.(a) Explain electrochemical corrosion.
(b) Explain galvanizing and tinning.
(c) Describe any two methods of synthesis in green chemistry.
[6+4+6]
5.(a) Describe with neat sketches, any two moulding techniques of plastics.
(b) What are the drawbacks of natural rubber.
(c) What are the different constituents of paints and give their function.
(d) Write notes on caustic embrittlement.
[6+4+3+3]
6.(a) Define calorific value, HCV and LCV. Calculate the gross and net calorific value of coal
having the following compositions C = 83%; H = 10%; S = 1%, N = 3%, Ash = 3%.
Latent heat of steam = 587 cal/g.
(b) Discuss (i) applications of Kohlrausch law (ii) scales and sludges
[10+6]
7.(a) Write notes on (i) deterioration of cement concrete (ii) Types of Liquid crystals (iii) Need
of green chemistry
(b) Explain (i) electrochemical cell (ii) metal cladding
[10+6]
Page 1 of 1
Set No - 2
Subject Code: R13104/R13
I B. Tech I Semester Regular Examinations Feb./Mar. - 2014
ENGINEERING CHEMISTRY
(Common to CE,ME,CSE,PCE,IT,Chem E,Aero E,AME,Min E,PE,Metal E)
Time: 3 hours Max. Marks: 70
Question Paper Consists of Part-A and Part-B
Answering the question in Part-A is Compulsory,
Three Questions should be answered from Part-B
*****
PART-A
1.(a) Write notes on (ii) CNG (ii) properties of Thiokol (iii) phosphate coatings
(b) Explain the mechanism of setting and hardening of cement.
(c) Calculate the amount of lime (84% pure) and soda (92% pure) required for softening
10, 000 litres of water containing the following salts per litre:
Ca(HCO
3
)
2
= 40.5 mg; Mg(HCO
3
)
2
= 36.5 mg; MgSO
4
= 30 mg; CaSO
4
= 34 mg;
CaCl
2
= 27.75 mg and NaCl = 10 mg. Also calculate the temporary hardness and
permanent hardness of the water sample.
[7+6+9]
PART-B
2.(a) Describe with neat sketch ion exchange process of softening of water.
(b) Write notes on (i) scales and sludges (ii) tacticity
(c) What is condensation polymerization? Explain with example.
[6+8+2]
3.(a) Describe the construction and working of hydrogen-oxygen fuel cell.
(b) At 25
0
C, the equivalent conductivities at infinite dilution of HCl, CH
3
COONa and NaCl
are 428.03, 93.3, and 125.78 ohm
-1
cm
2
equiv
-1
respectively. Calculate the equivalent
conductance of acetic acid at infinite dilution
(c) Discuss the ultimate analysis of coal
[7+3+6]
4.(a) Discuss the mechanism of dry corrosion. Explain the role of oxide film in dry corrosion.
(b) Explain the importance of design and selection of materials in controlling corrosion.
(c) Describe any two preparation methods for carbon nanotubes with neat sketch diagrams.
[6+4+6]
5.(a) Explain free radical mechanism of addition polymerization.
(b) Write the preparation and uses of (i) PVC (ii) Bakelite
(c) Write notes on (i) Reverse Osmosis (ii) anodic and cathodic inhibitors
[4+6+6]
6. Write notes on (i) refining (ii) octane number (iii) antiknocking agents (iv) cold lime soda
process (v) calomel electrode
[16]
7.(a) Write any four applications of (i) green chemistry (ii) liquid crystals (iii) fullerenes
(b) Write notes on (i) drying, semidrying and nondrying oils (ii) Kohlrausch law
[10+6]
Page 1 of 1
Set No - 3
Subject Code: R13104/R13
I B. Tech I Sem Regular Examinations Feb./Mar. - 2014
ENGINEERING CHEMISTRY
(Common to CE,ME,CSE,PCE,IT,Chem E,Aero E,AME,Min E,PE,Metal E)
Time: 3 hours Max. Marks: 70
Question Paper Consists of Part-A and Part-B
Answering the question in Part-A is Compulsory,
Three Questions should be answered from Part-B
*****
PART-A
1.(a) Write notes on (i) breakpoint chlorination (ii) ionic liquids as green solvents for
green synthesis (iii) electroless plating
(b) A sample of coal containing 93% C; 5% H; 2% ash. When this coal was tested in the
laboratory for its calorific value in the bomb calorimeter, the following data was
obtained: Weight of coal burnt = 0.95 g; Weight of water taken = 600g water equivalent
of bomb and calorimeter = 2,000 g, rise of temperature = 2.84
0
C; Cooling correction =
0.02
0
C; Fuse wire correction = 12.0 cal; acid correction = 55 cal. Calculate the net and
gross calorific value of the coal in cal/g. (Assume the latent heat of condensation of steam
as 580 cal/g)
(c) Compare galvanic series with electrochemical series.
[12+5+5]
PART-B
2.(a) Write notes on (i) demineralization process (ii) sterilization of water
(b) A sample of water contains the following dissolved salts per litre: Mg(HCO
3
)
2
= 25 mg;
MgCl
2
= 28 mg; CaSO
4
= 24 mg; CaCl
2
= 84 mg. Calculate the temporary and permanent
hardness.
(c) Discuss the physical and mechanical properties of polymers.
[6+4+6]
3.(a) What are secondary batteries? Give an example and explain its construction and
working.
(b) Describe conductometric titrations of acids and bases.
(c) Write notes on (i) petrol knocking and diesel knocking (ii) characteristics of a good fuel.
[5+5+6]
4.(a) Discuss on differential aeration corrosion
(b) Write notes on (i) Pilling- Bed worth rule (ii) passivity (iii) solar cells (iv) chemical vapour
deposition method of CNTs
[4+12]
5.(a) Write notes on (i) stereospecific polymers (ii) Injection moulding (iii) vulcanization
(b) Explain (i) metal cladding (ii) calgon and phosphate conditioning
[10+6]
6.(a) Describe moving bed catalytic cracking method with a neat labeled diagram.
(b) Write notes on flue analysis and its significance.
(c) Explain how specific and equivalent conductances of a strong electrolyte vary with
dilution.
(d) Discuss boiler corrosion.
[6+4+3+3]
Page 1 of 2
Set No - 4
FirstRanker.com - FirstRanker's Choice
Subject Code: R13104/R13
I B. Tech I Semester Regular Examinations Feb./Mar. - 2014
ENGINEERING CHEMISTRY
(Common to CE,ME,CSE,PCE,IT,Chem E,Aero E,AME,Min E,PE,Metal E)
Time: 3 hours Max. Marks: 70
Question Paper Consists of Part-A and Part-B
Answering the question in Part-A is Compulsory,
Three Questions should be answered from Part-B
*****
PART-A
1.(a) Discuss (i) p-type doped conducting polymers (ii) phosphate conditioning
(iii) antiknocking agents
(b) Write a note on protection (against corrosion) of a metal by metallic coatings.
(c) A 0.1 M KCl solution, whose specific conductance is 0.01571 mho cm
-1
, has a
conductance of 0.014 mho. When the same conductivity cell is used a 0.1 M chloroacetic
acid solution has a conductance of 7.84 x 10
-3
mho. If the ionic conductance of
ClCH
2
COO
-
and H
+
are 59.8 and 449.8 mhocm
2
equiv.
-1
, find the degree of dissociation
of chloroacetic acid.
[12+4+6]
PART-B
2.(a) Describe cold and hot lime soda processes with a neat diagram.
(b) A sample of water on analysis has been found to contain the following in ppm:
Ca (HCO
3
)
2
= 4.86; Mg (HCO
3
)
2
= 5.84, CaSO
4
= 6.8, MgSO
4
= 8.4. Calculate the
temporary and permanent hardness of water.
(c) Discuss (i) stereospecific polymers (ii) mechanical properties of polymers
[6+4+6]
3.(a) What is ion-selective electrode? Explain its working.
(b) Discuss potentiometric titrations.
(c) Write notes on (i) Refining of petrol (ii) reforming
[6+4+6]
4.(a) Explain the factors effecting the rate of corrosion.
(b) Write notes on Electroplating
(c) Discuss (i) bullet proof plastics (ii) green house effects
[6+4+6]
5.(a) Explain compounding and vulcanization of rubber.
(b) What is copolymerization. Give any two examples.
(c) Write notes on (i) caustic embrittlement (ii) galvanizing
[7+3+6]
6.(a) Write notes on (i) LPG (ii) diesel knocking (iii) Ni-Cd battery
(b) A sample of coal was found to contain the following constituents: C = 81%; O=7%;
S=2%; N=5.5% and ash=4.5%. Calculate the minimum amount of air required for
complete combustion of 1 kg of coal.
(c) Explain break-point chlorination of water.
[9+4+3]
7.(a) Write any four applications of carbon nanotubes.
(b) Explain the working of photovoltaic cells with a neat sketch.
(c) Write notes on (ii) Impressed current cathodic protection (ii) galvanic cell
[5+5+6]
Page 1 of 1
Set No - 1
Subject Code: R13104/R13
I B. Tech I Semester Regular Examinations Feb./Mar. - 2014
ENGINEERING CHEMISTRY
(Common to CE,ME,CSE,PCE,IT,Chem E,Aero E,AME,Min E,PE,Metal E)
Time: 3 hours Max. Marks: 70
Question Paper Consists of Part-A and Part-B
Answering the question in Part-A is Compulsory,
Three Questions should be answered from Part-B
*****
PART-A
1.(a) Name the various fractions obtained during fractional distillation of crude oil and indicate
their boiling point ranges and uses of various fractions.
(b) The ion conductance of H
+
and butyrate ions are 339.8 and 30.6 Scm
2
equiv
-1
respectively. When same conductance cell is employed 0.1 M KCl and 0.1 M butyric
acid recorded conductances of 1.3 x 10
-2
and 5.25 x 10
-4
Scm
2
respectively . If the
conductivity of the above KCl solution is 0.0121 S cm
-1
, calculate the degree of
dissociation of butyric acid.
(c) Write notes on (i) turbine deposits (ii) Anodized coatings (iii) Solar reflectors
[6+7+9]
PART-B
2.(a) Describe (i) zeolite process (ii) Priming and foaming
(b) Calculate the amount of lime and soda required for the softening of 150 liters of water,
which is analyzed as: temporary hardness = 20 ppm; permanent hardness = 15 ppm;
permanent Mg hardness = 10 ppm.
(c) Discuss the preparation of Bakelite and Thiokol and mention their uses.
[6+4+6]
3.(a) Explain with neat diagrams the working of (i) glass electrode (ii) concentration cell
(iii) Lechlanche cell
(b) Describe any one method of catalytic cracking process for obtaining gasoline.
[10+6]
4.(a) Explain electrochemical corrosion.
(b) Explain galvanizing and tinning.
(c) Describe any two methods of synthesis in green chemistry.
[6+4+6]
5.(a) Describe with neat sketches, any two moulding techniques of plastics.
(b) What are the drawbacks of natural rubber.
(c) What are the different constituents of paints and give their function.
(d) Write notes on caustic embrittlement.
[6+4+3+3]
6.(a) Define calorific value, HCV and LCV. Calculate the gross and net calorific value of coal
having the following compositions C = 83%; H = 10%; S = 1%, N = 3%, Ash = 3%.
Latent heat of steam = 587 cal/g.
(b) Discuss (i) applications of Kohlrausch law (ii) scales and sludges
[10+6]
7.(a) Write notes on (i) deterioration of cement concrete (ii) Types of Liquid crystals (iii) Need
of green chemistry
(b) Explain (i) electrochemical cell (ii) metal cladding
[10+6]
Page 1 of 1
Set No - 2
Subject Code: R13104/R13
I B. Tech I Semester Regular Examinations Feb./Mar. - 2014
ENGINEERING CHEMISTRY
(Common to CE,ME,CSE,PCE,IT,Chem E,Aero E,AME,Min E,PE,Metal E)
Time: 3 hours Max. Marks: 70
Question Paper Consists of Part-A and Part-B
Answering the question in Part-A is Compulsory,
Three Questions should be answered from Part-B
*****
PART-A
1.(a) Write notes on (ii) CNG (ii) properties of Thiokol (iii) phosphate coatings
(b) Explain the mechanism of setting and hardening of cement.
(c) Calculate the amount of lime (84% pure) and soda (92% pure) required for softening
10, 000 litres of water containing the following salts per litre:
Ca(HCO
3
)
2
= 40.5 mg; Mg(HCO
3
)
2
= 36.5 mg; MgSO
4
= 30 mg; CaSO
4
= 34 mg;
CaCl
2
= 27.75 mg and NaCl = 10 mg. Also calculate the temporary hardness and
permanent hardness of the water sample.
[7+6+9]
PART-B
2.(a) Describe with neat sketch ion exchange process of softening of water.
(b) Write notes on (i) scales and sludges (ii) tacticity
(c) What is condensation polymerization? Explain with example.
[6+8+2]
3.(a) Describe the construction and working of hydrogen-oxygen fuel cell.
(b) At 25
0
C, the equivalent conductivities at infinite dilution of HCl, CH
3
COONa and NaCl
are 428.03, 93.3, and 125.78 ohm
-1
cm
2
equiv
-1
respectively. Calculate the equivalent
conductance of acetic acid at infinite dilution
(c) Discuss the ultimate analysis of coal
[7+3+6]
4.(a) Discuss the mechanism of dry corrosion. Explain the role of oxide film in dry corrosion.
(b) Explain the importance of design and selection of materials in controlling corrosion.
(c) Describe any two preparation methods for carbon nanotubes with neat sketch diagrams.
[6+4+6]
5.(a) Explain free radical mechanism of addition polymerization.
(b) Write the preparation and uses of (i) PVC (ii) Bakelite
(c) Write notes on (i) Reverse Osmosis (ii) anodic and cathodic inhibitors
[4+6+6]
6. Write notes on (i) refining (ii) octane number (iii) antiknocking agents (iv) cold lime soda
process (v) calomel electrode
[16]
7.(a) Write any four applications of (i) green chemistry (ii) liquid crystals (iii) fullerenes
(b) Write notes on (i) drying, semidrying and nondrying oils (ii) Kohlrausch law
[10+6]
Page 1 of 1
Set No - 3
Subject Code: R13104/R13
I B. Tech I Sem Regular Examinations Feb./Mar. - 2014
ENGINEERING CHEMISTRY
(Common to CE,ME,CSE,PCE,IT,Chem E,Aero E,AME,Min E,PE,Metal E)
Time: 3 hours Max. Marks: 70
Question Paper Consists of Part-A and Part-B
Answering the question in Part-A is Compulsory,
Three Questions should be answered from Part-B
*****
PART-A
1.(a) Write notes on (i) breakpoint chlorination (ii) ionic liquids as green solvents for
green synthesis (iii) electroless plating
(b) A sample of coal containing 93% C; 5% H; 2% ash. When this coal was tested in the
laboratory for its calorific value in the bomb calorimeter, the following data was
obtained: Weight of coal burnt = 0.95 g; Weight of water taken = 600g water equivalent
of bomb and calorimeter = 2,000 g, rise of temperature = 2.84
0
C; Cooling correction =
0.02
0
C; Fuse wire correction = 12.0 cal; acid correction = 55 cal. Calculate the net and
gross calorific value of the coal in cal/g. (Assume the latent heat of condensation of steam
as 580 cal/g)
(c) Compare galvanic series with electrochemical series.
[12+5+5]
PART-B
2.(a) Write notes on (i) demineralization process (ii) sterilization of water
(b) A sample of water contains the following dissolved salts per litre: Mg(HCO
3
)
2
= 25 mg;
MgCl
2
= 28 mg; CaSO
4
= 24 mg; CaCl
2
= 84 mg. Calculate the temporary and permanent
hardness.
(c) Discuss the physical and mechanical properties of polymers.
[6+4+6]
3.(a) What are secondary batteries? Give an example and explain its construction and
working.
(b) Describe conductometric titrations of acids and bases.
(c) Write notes on (i) petrol knocking and diesel knocking (ii) characteristics of a good fuel.
[5+5+6]
4.(a) Discuss on differential aeration corrosion
(b) Write notes on (i) Pilling- Bed worth rule (ii) passivity (iii) solar cells (iv) chemical vapour
deposition method of CNTs
[4+12]
5.(a) Write notes on (i) stereospecific polymers (ii) Injection moulding (iii) vulcanization
(b) Explain (i) metal cladding (ii) calgon and phosphate conditioning
[10+6]
6.(a) Describe moving bed catalytic cracking method with a neat labeled diagram.
(b) Write notes on flue analysis and its significance.
(c) Explain how specific and equivalent conductances of a strong electrolyte vary with
dilution.
(d) Discuss boiler corrosion.
[6+4+3+3]
Page 1 of 2
Set No - 4
Subject Code: R13104/R13
7.(a) Write notes on (i) applications of liquid crystals (ii) any one method of green synthesis
(iii) fiber reinforced plastics
(b) Discuss sacrificial anodic protection method.
(c) Calculate the emf of the following cell: Zn (s)/Zn
2+
(0.1 M)// Cu
2+
(1.50M)/Cu(s) at
25
o
C. E
o
Zn2+/ Zn (s)
= -0.76 V and E
o
Cu2+ /Cu(s)
= +0.34 V.
[10+3+3]
Page 2 of 2
Set No - 4
FirstRanker.com - FirstRanker's Choice
This post was last modified on 03 December 2019