Download JNTUA B.Tech 1-1 R15 2017 Dec Supple 15A03101c Engineering Drawing Question Paper

Download JNTUA (JNTU Anantapur) B.Tech R15 (Bachelor of Technology) 1st Year 1st Semester (1-1) 2017 Dec Supple 15A03101c Engineering Drawing Previous Question Paper || Download B-Tech 1st Year 1st Sem 15A03101c Engineering Drawing Question Paper || JNTU Anantapur B.Tech R15 1-1 Previous Question Paper || JNTU Anantapur B.Tech ME 1-1 Previous Question Paper || JNTU Anantapur B.Tech CSE 1-1 Previous Question Paper || JNTU Anantapur B.Tech Mech 1-1 Previous Question Paper || JNTU Anantapur B.Tech EEE 1-1 Previous Question Paper || JNTU Anantapur B.Tech ECE 1-1 Previous Question Paper

This post was last modified on 11 September 2020

Download Document

JNTU Anantapur B-Tech 4-2 last 10 year question papers 2010 -2020 -All regulation- All branches- 4th Year 2nd Sem

Firstranker's choice

FirstRanker.com

Code: 15A03101c

--- Content provided by FirstRanker.com ---

B.Tech I Year I Semester (R15) Regular & Supplementary Examinations December 2017

ENGINEERING DRAWING

(Electrical and Electronics Engineering)

Time: 3 hours

Max. Marks: 70

--- Content provided by⁠ FirstRanker.com ---

(Answer all five units, 05 X 14 = 70 Marks)

*****

UNIT - I

Draw an ellipse by oblong method. The major and minor axes given as 150 mm and 90 mm respectively. Draw normal and tangent at any point on the ellipse at a distance of 55 mm from the geometrical center of the ellipse.
OR

--- Content provided by‌ FirstRanker.com ---

Show by means of a drawing that when the diameter of the directing circle is twice that of the generating circle, the hypocycloid is a straight line. Take the diameter of the generating circle equal to 50 mm.

UNIT - II

The distance between Delhi and Agra is 200 km and its equivalent distance on map measures 10 cm. Draw a diagonal scale to indicate 223 km and 135 km.
OR
(a) Draw the projections of the following points on the same reference line, keeping the projectors 50 mm apart.
1. A, in the HP and 30 mm infront of VP.
2. B, 45 mm below HP and in the VP.
3. C, 40 mm above HP and 20 infront of the VP.
(b) Two points A and B are in the H.P. The point A is 30 mm in front of the VP, while B is behind the VP. The distance between their projectors is 75 mm and the line joining their top views makes an angle of 45° with xy. Find the distance of the point B from the VP

UNIT - III

(a) A line AB, 100 mm long, is inclined at 30° to the HP and parallel to the VP. Its end A is in the HP and 30 mm infront of the VP. Draw its projections.

--- Content provided by FirstRanker.com ---

(b) Draw the projections of a regular pentagon of 25 mm side, with its surface making an angle of 45° with HP. One of the sides of the pentagon is parallel to HP and 15 mm away from it.
OR
A rhombus has its diagonals 100 mm and 60 mm long. Draw the projections of the rhombus when it is so placed that its top view appears to be a square of diagonals 60 mm long and the vertical plane through the longer diagonal makes 30 degrees with the VP.

UNIT - IV

A hexagonal prism, base 30 mm side and axis 75 mm long, has an edge of the base parallel to HP and inclined at 45° to the VP. Its axis makes an angle of 60° with the HP. Draw its projections.

--- Content provided by‍ FirstRanker.com ---

OR
A cone of base diameter 40 mm and slant height 60 mm is kept on the ground on its base. An AIP inclined at 45° to the HP cuts the cone through the midpoint of the axis. Draw the development of remaining portion after removing the cutting portion.

UNIT - V

Draw the isometric projection of the frustum of a hexagonal pyramid of bottom base side 30 mm and top base side 15 mm having a height of 65 mm. the frustum is resting on HP on its bottom base with one of the edge of the base parallel to VP.
OR

--- Content provided by FirstRanker.com ---

Draw the front view, top view and side view of the block shown in figure below. All dimensions are in mm.

Firstranker's choice

FirstRanker.com

Code: 15A03101c

B.Tech I Year I Semester (R15) Regular & Supplementary Examinations December 2017
--- Content provided by‍ FirstRanker.com ---

ENGINEERING DRAWING

(Electrical and Electronics Engineering)

Time: 3 hours

Max. Marks: 70

(Answer all five units, 05 X 14 = 70 Marks)
--- Content provided by FirstRanker.com ---

*****

UNIT - I
1. Draw an ellipse by oblong method. The major and minor axes given as 150 mm and 90 mm respectively. Draw normal and tangent at any point on the ellipse at a distance of 55 mm from the geometrical center of the ellipse.
2. OR
3. Show by means of a drawing that when the diameter of the directing circle is twice that of the generating circle, the hypocycloid is a straight line. Take the diameter of the generating circle equal to 50 mm.
UNIT - II
1. The distance between Delhi and Agra is 200 km and its equivalent distance on map measures 10 cm. Draw a diagonal scale to indicate 223 km and 135 km.
2. OR
3. (a) Draw the projections of the following points on the same reference line, keeping the projectors 50 mm apart.
  1. A, in the HP and 30 mm infront of VP.
  2. B, 45 mm below HP and in the VP.
  3. C, 40 mm above HP and 20 infront of the VP.
  (b) Two points A and B are in the H.P. The point A is 30 mm in front of the VP, while B is behind the VP. The distance between their projectors is 75 mm and the line joining their top views makes an angle of 45° with xy. Find the distance of the point B from the VP
UNIT - III
1. (a) A line AB, 100 mm long, is inclined at 30° to the HP and parallel to the VP. Its end A is in the HP and 30 mm infront of the VP. Draw its projections.
2. (b) Draw the projections of a regular pentagon of 25 mm side, with its surface making an angle of 45° with HP. One of the sides of the pentagon is parallel to HP and 15 mm away from it.
3. OR
4. A rhombus has its diagonals 100 mm and 60 mm long. Draw the projections of the rhombus when it is so placed that its top view appears to be a square of diagonals 60 mm long and the vertical plane through the longer diagonal makes 30 degrees with the VP.
UNIT - IV
1. A hexagonal prism, base 30 mm side and axis 75 mm long, has an edge of the base parallel to HP and inclined at 45° to the VP. Its axis makes an angle of 60° with the HP. Draw its projections.
2. OR
3. A cone of base diameter 40 mm and slant height 60 mm is kept on the ground on its base. An AIP inclined at 45° to the HP cuts the cone through the midpoint of the axis. Draw the development of remaining portion after removing the cutting portion.
UNIT - V
1. Draw the isometric projection of the frustum of a hexagonal pyramid of bottom base side 30 mm and top base side 15 mm having a height of 65 mm. the frustum is resting on HP on its bottom base with one of the edge of the base parallel to VP.
2. OR
3. Draw the front view, top view and side view of the block shown in figure below. All dimensions are in mm.
  --- Content provided by FirstRanker.com ---
  
  Firstranker's choice
  
  FirstRanker.com
  
  Code: 15A03101c
  
  B.Tech I Year I Semester (R15) Regular & Supplementary Examinations December 2017
  
  ENGINEERING DRAWING
  --- Content provided by‌ FirstRanker.com ---
  
  (Electrical and Electronics Engineering)
  
  Time: 3 hours
  
  Max. Marks: 70
  
  (Answer all five units, 05 X 14 = 70 Marks)
  
  *****
  --- Content provided by‌ FirstRanker.com ---
  
  UNIT - I
  1. Draw an ellipse by oblong method. The major and minor axes given as 150 mm and 90 mm respectively. Draw normal and tangent at any point on the ellipse at a distance of 55 mm from the geometrical center of the ellipse.
  2. OR
  3. Show by means of a drawing that when the diameter of the directing circle is twice that of the generating circle, the hypocycloid is a straight line. Take the diameter of the generating circle equal to 50 mm.
  UNIT - II
  --- Content provided by FirstRanker.com ---
  1. The distance between Delhi and Agra is 200 km and its equivalent distance on map measures 10 cm. Draw a diagonal scale to indicate 223 km and 135 km.
  2. OR
  3. (a) Draw the projections of the following points on the same reference line, keeping the projectors 50 mm apart.
    1. A, in the HP and 30 mm infront of VP.
    2. B, 45 mm below HP and in the VP.
    3. C, 40 mm above HP and 20 infront of the VP.
    (b) Two points A and B are in the H.P. The point A is 30 mm in front of the VP, while B is behind the VP. The distance between their projectors is 75 mm and the line joining their top views makes an angle of 45° with xy. Find the distance of the point B from the VP
  UNIT - III
  1. (a) A line AB, 100 mm long, is inclined at 30° to the HP and parallel to the VP. Its end A is in the HP and 30 mm infront of the VP. Draw its projections.
  2. (b) Draw the projections of a regular pentagon of 25 mm side, with its surface making an angle of 45° with HP. One of the sides of the pentagon is parallel to HP and 15 mm away from it.
  3. OR
  4. A rhombus has its diagonals 100 mm and 60 mm long. Draw the projections of the rhombus when it is so placed that its top view appears to be a square of diagonals 60 mm long and the vertical plane through the longer diagonal makes 30 degrees with the VP.
  UNIT - IV
  1. A hexagonal prism, base 30 mm side and axis 75 mm long, has an edge of the base parallel to HP and inclined at 45° to the VP. Its axis makes an angle of 60° with the HP. Draw its projections.
  2. OR
  3. A cone of base diameter 40 mm and slant height 60 mm is kept on the ground on its base. An AIP inclined at 45° to the HP cuts the cone through the midpoint of the axis. Draw the development of remaining portion after removing the cutting portion.
  UNIT - V
  1. Draw the isometric projection of the frustum of a hexagonal pyramid of bottom base side 30 mm and top base side 15 mm having a height of 65 mm. the frustum is resting on HP on its bottom base with one of the edge of the base parallel to VP.
  2. OR
  3. Draw the front view, top view and side view of the block shown in figure below. All dimensions are in mm.
    
    Firstranker's choice
    --- Content provided by⁠ FirstRanker.com ---
    
    FirstRanker.com
    
    Code: 15A03101c
    
    B.Tech I Year I Semester (R15) Regular & Supplementary Examinations December 2017
    
    ENGINEERING DRAWING
    
    (Electrical and Electronics Engineering)
    --- Content provided by‌ FirstRanker.com ---
    
    Time: 3 hours
    
    Max. Marks: 70
    
    (Answer all five units, 05 X 14 = 70 Marks)
    
    *****
    
    UNIT - I
    --- Content provided by FirstRanker.com ---
    1. Draw an ellipse by oblong method. The major and minor axes given as 150 mm and 90 mm respectively. Draw normal and tangent at any point on the ellipse at a distance of 55 mm from the geometrical center of the ellipse.
    2. OR
    3. Show by means of a drawing that when the diameter of the directing circle is twice that of the generating circle, the hypocycloid is a straight line. Take the diameter of the generating circle equal to 50 mm.
    UNIT - II
    1. The distance between Delhi and Agra is 200 km and its equivalent distance on map measures 10 cm. Draw a diagonal scale to indicate 223 km and 135 km.
    2. OR
    3. (a) Draw the projections of the following points on the same reference line, keeping the projectors 50 mm apart.
      1. A, in the HP and 30 mm infront of VP.
      2. B, 45 mm below HP and in the VP.
      3. C, 40 mm above HP and 20 infront of the VP.
      (b) Two points A and B are in the H.P. The point A is 30 mm in front of the VP, while B is behind the VP. The distance between their projectors is 75 mm and the line joining their top views makes an angle of 45° with xy. Find the distance of the point B from the VP
    UNIT - III
    1. (a) A line AB, 100 mm long, is inclined at 30° to the HP and parallel to the VP. Its end A is in the HP and 30 mm infront of the VP. Draw its projections.
    2. (b) Draw the projections of a regular pentagon of 25 mm side, with its surface making an angle of 45° with HP. One of the sides of the pentagon is parallel to HP and 15 mm away from it.
    3. OR
    4. A rhombus has its diagonals 100 mm and 60 mm long. Draw the projections of the rhombus when it is so placed that its top view appears to be a square of diagonals 60 mm long and the vertical plane through the longer diagonal makes 30 degrees with the VP.
    UNIT - IV
    1. A hexagonal prism, base 30 mm side and axis 75 mm long, has an edge of the base parallel to HP and inclined at 45° to the VP. Its axis makes an angle of 60° with the HP. Draw its projections.
    2. OR
    3. A cone of base diameter 40 mm and slant height 60 mm is kept on the ground on its base. An AIP inclined at 45° to the HP cuts the cone through the midpoint of the axis. Draw the development of remaining portion after removing the cutting portion.
    UNIT - V
    --- Content provided by FirstRanker.com ---
    1. Draw the isometric projection of the frustum of a hexagonal pyramid of bottom base side 30 mm and top base side 15 mm having a height of 65 mm. the frustum is resting on HP on its bottom base with one of the edge of the base parallel to VP.
    2. OR
    3. Draw the front view, top view and side view of the block shown in figure below. All dimensions are in mm.
      
      Firstranker's choice
      
      FirstRanker.com
      --- Content provided by FirstRanker.com ---
      
      Code: 15A03101c
      
      B.Tech I Year I Semester (R15) Regular & Supplementary Examinations December 2017
      
      ENGINEERING DRAWING
      
      (Electrical and Electronics Engineering)
      
      Time: 3 hours
      --- Content provided by⁠ FirstRanker.com ---
      
      Max. Marks: 70
      
      (Answer all five units, 05 X 14 = 70 Marks)
      
      *****
      
      UNIT - I
      1. Draw an ellipse by oblong method. The major and minor axes given as 150 mm and 90 mm respectively. Draw normal and tangent at any point on the ellipse at a distance of 55 mm from the geometrical center of the ellipse.
      2. OR
      3. Show by means of a drawing that when the diameter of the directing circle is twice that of the generating circle, the hypocycloid is a straight line. Take the diameter of the generating circle equal to 50 mm.
      UNIT - II
      1. The distance between Delhi and Agra is 200 km and its equivalent distance on map measures 10 cm. Draw a diagonal scale to indicate 223 km and 135 km.
      2. OR
      3. (a) Draw the projections of the following points on the same reference line, keeping the projectors 50 mm apart.
        
        A, in the HP and 30 mm infront of VP.
        
        B, 45 mm below HP and in the VP.
        
        C, 40 mm above HP and 20 infront of the VP.
        
        (b) Two points A and B are in the H.P. The point A is 30 mm in front of the VP, while B is behind the VP. The distance between their projectors is 75 mm and the line joining their top views makes an angle of 45° with xy. Find the distance of the point B from the VP
      UNIT - III
      --- Content provided by‍ FirstRanker.com ---
      1. (a) A line AB, 100 mm long, is inclined at 30° to the HP and parallel to the VP. Its end A is in the HP and 30 mm infront of the VP. Draw its projections.
      2. (b) Draw the projections of a regular pentagon of 25 mm side, with its surface making an angle of 45° with HP. One of the sides of the pentagon is parallel to HP and 15 mm away from it.
      3. OR
      4. A rhombus has its diagonals 100 mm and 60 mm long. Draw the projections of the rhombus when it is so placed that its top view appears to be a square of diagonals 60 mm long and the vertical plane through the longer diagonal makes 30 degrees with the VP.
      UNIT - IV
      --- Content provided by‍ FirstRanker.com ---
      1. A hexagonal prism, base 30 mm side and axis 75 mm long, has an edge of the base parallel to HP and inclined at 45° to the VP. Its axis makes an angle of 60° with the HP. Draw its projections.
      2. OR
      3. A cone of base diameter 40 mm and slant height 60 mm is kept on the ground on its base. An AIP inclined at 45° to the HP cuts the cone through the midpoint of the axis. Draw the development of remaining portion after removing the cutting portion.
      UNIT - V
      1. Draw the isometric projection of the frustum of a hexagonal pyramid of bottom base side 30 mm and top base side 15 mm having a height of 65 mm. the frustum is resting on HP on its bottom base with one of the edge of the base parallel to VP.
      2. OR
      3. Draw the front view, top view and side view of the block shown in figure below. All dimensions are in mm.
        
        Firstranker's choice
        
        FirstRanker.com
        
        Code: 15A03101c
        --- Content provided by‍ FirstRanker.com ---
        
        B.Tech I Year I Semester (R15) Regular & Supplementary Examinations December 2017
        
        ENGINEERING DRAWING
        
        (Electrical and Electronics Engineering)
        
        Time: 3 hours
        
        Max. Marks: 70
        --- Content provided by‌ FirstRanker.com ---
        
        (Answer all five units, 05 X 14 = 70 Marks)
        
        *****
        
        UNIT - I
        
        Draw an ellipse by oblong method. The major and minor axes given as 150 mm and 90 mm respectively. Draw normal and tangent at any point on the ellipse at a distance of 55 mm from the geometrical center of the ellipse.
        
        OR
        --- Content provided by FirstRanker.com ---
        
        Show by means of a drawing that when the diameter of the directing circle is twice that of the generating circle, the hypocycloid is a straight line. Take the diameter of the generating circle equal to 50 mm.
        
        UNIT - II
        
        The distance between Delhi and Agra is 200 km and its equivalent distance on map measures 10 cm. Draw a diagonal scale to indicate 223 km and 135 km.
        
        OR
        
        (a) Draw the projections of the following points on the same reference line, keeping the projectors 50 mm apart.
        
        A, in the HP and 30 mm infront of VP.
        --- Content provided by FirstRanker.com ---
        
        B, 45 mm below HP and in the VP.
        
        C, 40 mm above HP and 20 infront of the VP.
        
        (b) Two points A and B are in the H.P. The point A is 30 mm in front of the VP, while B is behind the VP. The distance between their projectors is 75 mm and the line joining their top views makes an angle of 45° with xy. Find the distance of the point B from the VP
        
        UNIT - III
        
        (a) A line AB, 100 mm long, is inclined at 30° to the HP and parallel to the VP. Its end A is in the HP and 30 mm infront of the VP. Draw its projections.
        --- Content provided by FirstRanker.com ---
        
        (b) Draw the projections of a regular pentagon of 25 mm side, with its surface making an angle of 45° with HP. One of the sides of the pentagon is parallel to HP and 15 mm away from it.
        
        OR
        
        A rhombus has its diagonals 100 mm and 60 mm long. Draw the projections of the rhombus when it is so placed that its top view appears to be a square of diagonals 60 mm long and the vertical plane through the longer diagonal makes 30 degrees with the VP.
        
        UNIT - IV
        
        A hexagonal prism, base 30 mm side and axis 75 mm long, has an edge of the base parallel to HP and inclined at 45° to the VP. Its axis makes an angle of 60° with the HP. Draw its projections.
        --- Content provided by FirstRanker.com ---
        
        OR
        
        A cone of base diameter 40 mm and slant height 60 mm is kept on the ground on its base. An AIP inclined at 45° to the HP cuts the cone through the midpoint of the axis. Draw the development of remaining portion after removing the cutting portion.
        
        UNIT - V
        
        Draw the isometric projection of the frustum of a hexagonal pyramid of bottom base side 30 mm and top base side 15 mm having a height of 65 mm. the frustum is resting on HP on its bottom base with one of the edge of the base parallel to VP.
        
        OR
        --- Content provided by FirstRanker.com ---
        
        Draw the front view, top view and side view of the block shown in figure below. All dimensions are in mm.
        
        Firstranker's choice
        
        FirstRanker.com
        
        Code: 15A03101c
        
        B.Tech I Year I Semester (R15) Regular & Supplementary Examinations December 2017
        --- Content provided by‍ FirstRanker.com ---
        
        ENGINEERING DRAWING
        
        (Electrical and Electronics Engineering)
        
        Time: 3 hours
        
        Max. Marks: 70
        
        (Answer all five units, 05 X 14 = 70 Marks)
        --- Content provided by⁠ FirstRanker.com ---
        
        *****
        
        UNIT - I
        
        Draw an ellipse by oblong method. The major and minor axes given as 150 mm and 90 mm respectively. Draw normal and tangent at any point on the ellipse at a distance of 55 mm from the geometrical center of the ellipse.
        
        OR
        
        Show by means of a drawing that when the diameter of the directing circle is twice that of the generating circle, the hypocycloid is a straight line. Take the diameter of the generating circle equal to 50 mm.
        --- Content provided by⁠ FirstRanker.com ---
        
        UNIT - II
        
        The distance between Delhi and Agra is 200 km and its equivalent distance on map measures 10 cm. Draw a diagonal scale to indicate 223 km and 135 km.
        
        OR
        
        (a) Draw the projections of the following points on the same reference line, keeping the projectors 50 mm apart.
        
        A, in the HP and 30 mm infront of VP.
        
        B, 45 mm below HP and in the VP.
        --- Content provided by FirstRanker.com ---
        
        C, 40 mm above HP and 20 infront of the VP.
        
        (b) Two points A and B are in the H.P. The point A is 30 mm in front of the VP, while B is behind the VP. The distance between their projectors is 75 mm and the line joining their top views makes an angle of 45° with xy. Find the distance of the point B from the VP
        
        UNIT - III
        
        (a) A line AB, 100 mm long, is inclined at 30° to the HP and parallel to the VP. Its end A is in the HP and 30 mm infront of the VP. Draw its projections.
        
        (b) Draw the projections of a regular pentagon of 25 mm side, with its surface making an angle of 45° with HP. One of the sides of the pentagon is parallel to HP and 15 mm away from it.
        --- Content provided by‍ FirstRanker.com ---
        
        OR
        
        A rhombus has its diagonals 100 mm and 60 mm long. Draw the projections of the rhombus when it is so placed that its top view appears to be a square of diagonals 60 mm long and the vertical plane through the longer diagonal makes 30 degrees with the VP.
        
        UNIT - IV
        
        A hexagonal prism, base 30 mm side and axis 75 mm long, has an edge of the base parallel to HP and inclined at 45° to the VP. Its axis makes an angle of 60° with the HP. Draw its projections.
        
        OR
        --- Content provided by‍ FirstRanker.com ---
        
        A cone of base diameter 40 mm and slant height 60 mm is kept on the ground on its base. An AIP inclined at 45° to the HP cuts the cone through the midpoint of the axis. Draw the development of remaining portion after removing the cutting portion.
        
        UNIT - V
        
        Draw the isometric projection of the frustum of a hexagonal pyramid of bottom base side 30 mm and top base side 15 mm having a height of 65 mm. the frustum is resting on HP on its bottom base with one of the edge of the base parallel to VP.
        
        OR
        
        Draw the front view, top view and side view of the block shown in figure below. All dimensions are in mm.
        --- Content provided by‌ FirstRanker.com ---
        
        Firstranker's choice
        
        FirstRanker.com
        
        Code: 15A03101c
        
        B.Tech I Year I Semester (R15) Regular & Supplementary Examinations December 2017
        
        ENGINEERING DRAWING
        --- Content provided by FirstRanker.com ---
        
        (Electrical and Electronics Engineering)
        
        Time: 3 hours
        
        Max. Marks: 70
        
        (Answer all five units, 05 X 14 = 70 Marks)
        
        *****
        --- Content provided by FirstRanker.com ---
        
        UNIT - I
        
        Draw an ellipse by oblong method. The major and minor axes given as 150 mm and 90 mm respectively. Draw normal and tangent at any point on the ellipse at a distance of 55 mm from the geometrical center of the ellipse.
        
        OR
        
        Show by means of a drawing that when the diameter of the directing circle is twice that of the generating circle, the hypocycloid is a straight line. Take the diameter of the generating circle equal to 50 mm.
        
        UNIT - II
        --- Content provided by FirstRanker.com ---
        
        The distance between Delhi and Agra is 200 km and its equivalent distance on map measures 10 cm. Draw a diagonal scale to indicate 223 km and 135 km.
        
        OR
        
        (a) Draw the projections of the following points on the same reference line, keeping the projectors 50 mm apart.
        
        A, in the HP and 30 mm infront of VP.
        
        B, 45 mm below HP and in the VP.
        
        C, 40 mm above HP and 20 infront of the VP.
        --- Content provided by‌ FirstRanker.com ---
        
        (b) Two points A and B are in the H.P. The point A is 30 mm in front of the VP, while B is behind the VP. The distance between their projectors is 75 mm and the line joining their top views makes an angle of 45° with xy. Find the distance of the point B from the VP
        
        UNIT - III
        
        (a) A line AB, 100 mm long, is inclined at 30° to the HP and parallel to the VP. Its end A is in the HP and 30 mm infront of the VP. Draw its projections.
        
        (b) Draw the projections of a regular pentagon of 25 mm side, with its surface making an angle of 45° with HP. One of the sides of the pentagon is parallel to HP and 15 mm away from it.
        
        OR
        --- Content provided by‌ FirstRanker.com ---
        
        A rhombus has its diagonals 100 mm and 60 mm long. Draw the projections of the rhombus when it is so placed that its top view appears to be a square of diagonals 60 mm long and the vertical plane through the longer diagonal makes 30 degrees with the VP.
        
        UNIT - IV
        
        A hexagonal prism, base 30 mm side and axis 75 mm long, has an edge of the base parallel to HP and inclined at 45° to the VP. Its axis makes an angle of 60° with the HP. Draw its projections.
        
        OR
        
        A cone of base diameter 40 mm and slant height 60 mm is kept on the ground on its base. An AIP inclined at 45° to the HP cuts the cone through the midpoint of the axis. Draw the development of remaining portion after removing the cutting portion.
        --- Content provided by FirstRanker.com ---
        
        UNIT - V
        
        Draw the isometric projection of the frustum of a hexagonal pyramid of bottom base side 30 mm and top base side 15 mm having a height of 65 mm. the frustum is resting on HP on its bottom base with one of the edge of the base parallel to VP.
        
        OR
        
        Draw the front view, top view and side view of the block shown in figure below. All dimensions are in mm.
        
        Firstranker's choice
        --- Content provided by‍ FirstRanker.com ---
        
        FirstRanker.com
        
        Code: 15A03101c
        
        B.Tech I Year I Semester (R15) Regular & Supplementary Examinations December 2017
        
        ENGINEERING DRAWING
        
        (Electrical and Electronics Engineering)
        --- Content provided by FirstRanker.com ---
        
        Time: 3 hours
        
        Max. Marks: 70
        
        (Answer all five units, 05 X 14 = 70 Marks)
        
        *****
        
        UNIT - I
        --- Content provided by‍ FirstRanker.com ---
        
        Draw an ellipse by oblong method. The major and minor axes given as 150 mm and 90 mm respectively. Draw normal and tangent at any point on the ellipse at a distance of 55 mm from the geometrical center of the ellipse.
        
        OR
        
        Show by means of a drawing that when the diameter of the directing circle is twice that of the generating circle, the hypocycloid is a straight line. Take the diameter of the generating circle equal to 50 mm.
        
        UNIT - II
        
        The distance between Delhi and Agra is 200 km and its equivalent distance on map measures 10 cm. Draw a diagonal scale to indicate 223 km and 135 km.
        --- Content provided by⁠ FirstRanker.com ---
        
        OR
        
        (a) Draw the projections of the following points on the same reference line, keeping the projectors 50 mm apart.
        
        A, in the HP and 30 mm infront of VP.
        
        B, 45 mm below HP and in the VP.
        
        C, 40 mm above HP and 20 infront of the VP.
        
        (b) Two points A and B are in the H.P. The point A is 30 mm in front of the VP, while B is behind the VP. The distance between their projectors is 75 mm and the line joining their top views makes an angle of 45° with xy. Find the distance of the point B from the VP
        --- Content provided by⁠ FirstRanker.com ---
        
        UNIT - III
        
        (a) A line AB, 100 mm long, is inclined at 30° to the HP and parallel to the VP. Its end A is in the HP and 30 mm infront of the VP. Draw its projections.
        
        (b) Draw the projections of a regular pentagon of 25 mm side, with its surface making an angle of 45° with HP. One of the sides of the pentagon is parallel to HP and 15 mm away from it.
        
        OR
        
        A rhombus has its diagonals 100 mm and 60 mm long. Draw the projections of the rhombus when it is so placed that its top view appears to be a square of diagonals 60 mm long and the vertical plane through the longer diagonal makes 30 degrees with the VP.
        --- Content provided by‌ FirstRanker.com ---
        
        UNIT - IV
        
        A hexagonal prism, base 30 mm side and axis 75 mm long, has an edge of the base parallel to HP and inclined at 45° to the VP. Its axis makes an angle of 60° with the HP. Draw its projections.
        
        OR
        
        A cone of base diameter 40 mm and slant height 60 mm is kept on the ground on its base. An AIP inclined at 45° to the HP cuts the cone through the midpoint of the axis. Draw the development of remaining portion after removing the cutting portion.
        
        UNIT - V
        --- Content provided by‍ FirstRanker.com ---
        
        Draw the isometric projection of the frustum of a hexagonal pyramid of bottom base side 30 mm and top base side 15 mm having a height of 65 mm. the frustum is resting on HP on its bottom base with one of the edge of the base parallel to VP.
        
        OR
        
        Draw the front view, top view and side view of the block shown in figure below. All dimensions are in mm.
        
        Firstranker's choice
        
        FirstRanker.com
        --- Content provided by⁠ FirstRanker.com ---
        
        Code: 15A03101c
        
        B.Tech I Year I Semester (R15) Regular & Supplementary Examinations December 2017
        
        ENGINEERING DRAWING
        
        (Electrical and Electronics Engineering)
        
        Time: 3 hours
        --- Content provided by FirstRanker.com ---
        
        Max. Marks: 70
        
        (Answer all five units, 05 X 14 = 70 Marks)
        
        *****
        
        UNIT - I
        
        Draw an ellipse by oblong method. The major and minor axes given as 150 mm and 90 mm respectively. Draw normal and tangent at any point on the ellipse at a distance of 55 mm from the geometrical center of the ellipse.
        --- Content provided by FirstRanker.com ---
        
        OR
        
        Show by means of a drawing that when the diameter of the directing circle is twice that of the generating circle, the hypocycloid is a straight line. Take the diameter of the generating circle equal to 50 mm.
        
        UNIT - II
        
        The distance between Delhi and Agra is 200 km and its equivalent distance on map measures 10 cm. Draw a diagonal scale to indicate 223 km and 135 km.
        
        OR
        --- Content provided by⁠ FirstRanker.com ---
        
        (a) Draw the projections of the following points on the same reference line, keeping the projectors 50 mm apart.
        
        A, in the HP and 30 mm infront of VP.
        
        B, 45 mm below HP and in the VP.
        
        C, 40 mm above HP and 20 infront of the VP.
        
        (b) Two points A and B are in the H.P. The point A is 30 mm in front of the VP, while B is behind the VP. The distance between their projectors is 75 mm and the line joining their top views makes an angle of 45° with xy. Find the distance of the point B from the VP
        
        UNIT - III
        --- Content provided by⁠ FirstRanker.com ---
        
        (a) A line AB, 100 mm long, is inclined at 30° to the HP and parallel to the VP. Its end A is in the HP and 30 mm infront of the VP. Draw its projections.
        
        (b) Draw the projections of a regular pentagon of 25 mm side, with its surface making an angle of 45° with HP. One of the sides of the pentagon is parallel to HP and 15 mm away from it.
        
        OR
        
        A rhombus has its diagonals 100 mm and 60 mm long. Draw the projections of the rhombus when it is so placed that its top view appears to be a square of diagonals 60 mm long and the vertical plane through the longer diagonal makes 30 degrees with the VP.
        
        UNIT - IV
        --- Content provided by‌ FirstRanker.com ---
        
        A hexagonal prism, base 30 mm side and axis 75 mm long, has an edge of the base parallel to HP and inclined at 45° to the VP. Its axis makes an angle of 60° with the HP. Draw its projections.
        
        OR
        
        A cone of base diameter 40 mm and slant height 60 mm is kept on the ground on its base. An AIP inclined at 45° to the HP cuts the cone through the midpoint of the axis. Draw the development of remaining portion after removing the cutting portion.
        
        UNIT - V
        
        Draw the isometric projection of the frustum of a hexagonal pyramid of bottom base side 30 mm and top base side 15 mm having a height of 65 mm. the frustum is resting on HP on its bottom base with one of the edge of the base parallel to VP.
        --- Content provided by‌ FirstRanker.com ---
        
        OR
        
        Draw the front view, top view and side view of the block shown in figure below. All dimensions are in mm.
        
        Firstranker's choice
        
        FirstRanker.com
        
        Code: 15A03101c
        --- Content provided by FirstRanker.com ---
        
        B.Tech I Year I Semester (R15) Regular & Supplementary Examinations December 2017
        
        ENGINEERING DRAWING
        
        (Electrical and Electronics Engineering)
        
        Time: 3 hours
        
        Max. Marks: 70
        --- Content provided by FirstRanker.com ---
        
        (Answer all five units, 05 X 14 = 70 Marks)
        
        *****
        
        UNIT - I
        
        Draw an ellipse by oblong method. The major and minor axes given as 150 mm and 90 mm respectively. Draw normal and tangent at any point on the ellipse at a distance of 55 mm from the geometrical center of the ellipse.
        
        OR
        --- Content provided by FirstRanker.com ---
        
        Show by means of a drawing that when the diameter of the directing circle is twice that of the generating circle, the hypocycloid is a straight line. Take the diameter of the generating circle equal to 50 mm.
        
        UNIT - II
        
        The distance between Delhi and Agra is 200 km and its equivalent distance on map measures 10 cm. Draw a diagonal scale to indicate 223 km and 135 km.
        
        OR
        
        (a) Draw the projections of the following points on the same reference line, keeping the projectors 50 mm apart.
        
        A, in the HP and 30 mm infront of VP.
        --- Content provided by⁠ FirstRanker.com ---
        
        B, 45 mm below HP and in the VP.
        
        C, 40 mm above HP and 20 infront of the VP.
        
        (b) Two points A and B are in the H.P. The point A is 30 mm in front of the VP, while B is behind the VP. The distance between their projectors is 75 mm and the line joining their top views makes an angle of 45° with xy. Find the distance of the point B from the VP
        
        UNIT - III
        
        (a) A line AB, 100 mm long, is inclined at 30° to the HP and parallel to the VP. Its end A is in the HP and 30 mm infront of the VP. Draw its projections.
        --- Content provided by⁠ FirstRanker.com ---
        
        (b) Draw the projections of a regular pentagon of 25 mm side, with its surface making an angle of 45° with HP. One of the sides of the pentagon is parallel to HP and 15 mm away from it.
        
        OR
        
        A rhombus has its diagonals 100 mm and 60 mm long. Draw the projections of the rhombus when it is so placed that its top view appears to be a square of diagonals 60 mm long and the vertical plane through the longer diagonal makes 30 degrees with the VP.
        
        UNIT - IV
        
        A hexagonal prism, base 30 mm side and axis 75 mm long, has an edge of the base parallel to HP and inclined at 45° to the VP. Its axis makes an angle of 60° with the HP. Draw its projections.
        --- Content provided by‍ FirstRanker.com ---
        
        OR
        
        A cone of base diameter 40 mm and slant height 60 mm is kept on the ground on its base. An AIP inclined at 45° to the HP cuts the cone through the midpoint of the axis. Draw the development of remaining portion after removing the cutting portion.
        
        UNIT - V
        
        Draw the isometric projection of the frustum of a hexagonal pyramid of bottom base side 30 mm and top base side 15 mm having a height of 65 mm. the frustum is resting on HP on its bottom base with one of the edge of the base parallel to VP.
        
        OR
        --- Content provided by FirstRanker.com ---
        
        Draw the front view, top view and side view of the block shown in figure below. All dimensions are in mm.
        
        Firstranker's choice
        
        FirstRanker.com
        
        Code: 15A03101c
        
        B.Tech I Year I Semester (R15) Regular & Supplementary Examinations December 2017
        --- Content provided by FirstRanker.com ---
        
        ENGINEERING DRAWING
        
        (Electrical and Electronics Engineering)
        
        Time: 3 hours
        
        Max. Marks: 70
        
        (Answer all five units, 05 X 14 = 70 Marks)
        --- Content provided by FirstRanker.com ---
        
        *****
        
        UNIT - I
        
        Draw an ellipse by oblong method. The major and minor axes given as 150 mm and 90 mm respectively. Draw normal and tangent at any point on the ellipse at a distance of 55 mm from the geometrical center of the ellipse.
        
        OR
        
        Show by means of a drawing that when the diameter of the directing circle is twice that of the generating circle, the hypocycloid is a straight line. Take the diameter of the generating circle equal to 50 mm.
        --- Content provided by⁠ FirstRanker.com ---
        
        UNIT - II
        
        The distance between Delhi and Agra is 200 km and its equivalent distance on map measures 10 cm. Draw a diagonal scale to indicate 223 km and 135 km.
        
        OR
        
        (a) Draw the projections of the following points on the same reference line, keeping the projectors 50 mm apart.
        
        A, in the HP and 30 mm infront of VP.
        
        B, 45 mm below HP and in the VP.
        --- Content provided by⁠ FirstRanker.com ---
        
        C, 40 mm above HP and 20 infront of the VP.
        
        (b) Two points A and B are in the H.P. The point A is 30 mm in front of the VP, while B is behind the VP. The distance between their projectors is 75 mm and the line joining their top views makes an angle of 45° with xy. Find the distance of the point B from the VP
        
        UNIT - III
        
        (a) A line AB, 100 mm long, is inclined at 30° to the HP and parallel to the VP. Its end A is in the HP and 30 mm infront of the VP. Draw its projections.
        
        (b) Draw the projections of a regular pentagon of 25 mm side, with its surface making an angle of 45° with HP. One of the sides of the pentagon is parallel to HP and 15 mm away from it.
        --- Content provided by‍ FirstRanker.com ---
        
        OR
        
        A rhombus has its diagonals 100 mm and 60 mm long. Draw the projections of the rhombus when it is so placed that its top view appears to be a square of diagonals 60 mm long and the vertical plane through the longer diagonal makes 30 degrees with the VP.
        
        UNIT - IV
        
        A hexagonal prism, base 30 mm side and axis 75 mm long, has an edge of the base parallel to HP and inclined at 45° to the VP. Its axis makes an angle of 60° with the HP. Draw its projections.
        
        OR
        --- Content provided by‌ FirstRanker.com ---
        
        A cone of base diameter 40 mm and slant height 60 mm is kept on the ground on its base. An AIP inclined at 45° to the HP cuts the cone through the midpoint of the axis. Draw the development of remaining portion after removing the cutting portion.
        
        UNIT - V
        
        Draw the isometric projection of the frustum of a hexagonal pyramid of bottom base side 30 mm and top base side 15 mm having a height of 65 mm. the frustum is resting on HP on its bottom base with one of the edge of the base parallel to VP.
        
        OR
        
        Draw the front view, top view and side view of the block shown in figure below. All dimensions are in mm.
        --- Content provided by FirstRanker.com ---
        
        Firstranker's choice
        
        FirstRanker.com
        
        Code: 15A03101c
        
        B.Tech I Year I Semester (R15) Regular & Supplementary Examinations December 2017
        
        ENGINEERING DRAWING
        --- Content provided by FirstRanker.com ---
        
        (Electrical and Electronics Engineering)
        
        Time: 3 hours
        
        Max. Marks: 70
        
        (Answer all five units, 05 X 14 = 70 Marks)
        
        *****
        --- Content provided by FirstRanker.com ---
        
        UNIT - I
        
        Draw an ellipse by oblong method. The major and minor axes given as 150 mm and 90 mm respectively. Draw normal and tangent at any point on the ellipse at a distance of 55 mm from the geometrical center of the ellipse.
        
        OR
        
        Show by means of a drawing that when the diameter of the directing circle is twice that of the generating circle, the hypocycloid is a straight line. Take the diameter of the generating circle equal to 50 mm.
        
        UNIT - II
        --- Content provided by⁠ FirstRanker.com ---
        
        The distance between Delhi and Agra is 200 km and its equivalent distance on map measures 10 cm. Draw a diagonal scale to indicate 223 km and 135 km.
        
        OR
        
        (a) Draw the projections of the following points on the same reference line, keeping the projectors 50 mm apart.
        
        A, in the HP and 30 mm infront of VP.
        
        B, 45 mm below HP and in the VP.
        
        C, 40 mm above HP and 20 infront of the VP.
        --- Content provided by‌ FirstRanker.com ---
        
        (b) Two points A and B are in the H.P. The point A is 30 mm in front of the VP, while B is behind the VP. The distance between their projectors is 75 mm and the line joining their top views makes an angle of 45° with xy. Find the distance of the point B from the VP
        
        UNIT - III
        
        (a) A line AB, 100 mm long, is inclined at 30° to the HP and parallel to the VP. Its end A is in the HP and 30 mm infront of the VP. Draw its projections.
        
        (b) Draw the projections of a regular pentagon of 25 mm side, with its surface making an angle of 45° with HP. One of the sides of the pentagon is parallel to HP and 15 mm away from it.
        
        OR
        --- Content provided by FirstRanker.com ---
        
        A rhombus has its diagonals 100 mm and 60 mm long. Draw the projections of the rhombus when it is so placed that its top view appears to be a square of diagonals 60 mm long and the vertical plane through the longer diagonal makes 30 degrees with the VP.
        
        UNIT - IV
        
        A hexagonal prism, base 30 mm side and axis 75 mm long, has an edge of the base parallel to HP and inclined at 45° to the VP. Its axis makes an angle of 60° with the HP. Draw its projections.
        
        OR
        
        A cone of base diameter 40 mm and slant height 60 mm is kept on the ground on its base. An AIP inclined at 45° to the HP cuts the cone through the midpoint of the axis. Draw the development of remaining portion after removing the cutting portion.
        --- Content provided by⁠ FirstRanker.com ---
        
        UNIT - V
        
        Draw the isometric projection of the frustum of a hexagonal pyramid of bottom base side 30 mm and top base side 15 mm having a height of 65 mm. the frustum is resting on HP on its bottom base with one of the edge of the base parallel to VP.
        
        OR
        
        Draw the front view, top view and side view of the block shown in figure below. All dimensions are in mm.
        
        Firstranker's choice
        --- Content provided by‌ FirstRanker.com ---
        
        FirstRanker.com
        
        Code: 15A03101c
        
        B.Tech I Year I Semester (R15) Regular & Supplementary Examinations December 2017
        
        ENGINEERING DRAWING
        
        (Electrical and Electronics Engineering)
        --- Content provided by⁠ FirstRanker.com ---
        
        Time: 3 hours
        
        Max. Marks: 70
        
        (Answer all five units, 05 X 14 = 70 Marks)
        
        *****
        
        UNIT - I
        --- Content provided by FirstRanker.com ---
        
        Draw an ellipse by oblong method. The major and minor axes given as 150 mm and 90 mm respectively. Draw normal and tangent at any point on the ellipse at a distance of 55 mm from the geometrical center of the ellipse.
        
        OR
        
        Show by means of a drawing that when the diameter of the directing circle is twice that of the generating circle, the hypocycloid is a straight line. Take the diameter of the generating circle equal to 50 mm.
        
        UNIT - II
        
        The distance between Delhi and Agra is 200 km and its equivalent distance on map measures 10 cm. Draw a diagonal scale to indicate 223 km and 135 km.
        --- Content provided by⁠ FirstRanker.com ---
        
        OR
        
        (a) Draw the projections of the following points on the same reference line, keeping the projectors 50 mm apart.
        
        A, in the HP and 30 mm infront of VP.
        
        B, 45 mm below HP and in the VP.
        
        C, 40 mm above HP and 20 infront of the VP.
        
        (b) Two points A and B are in the H.P. The point A is 30 mm in front of the VP, while B is behind the VP. The distance between their projectors is 75 mm and the line joining their top views makes an angle of 45° with xy. Find the distance of the point B from the VP
        --- Content provided by FirstRanker.com ---
        
        UNIT - III
        
        (a) A line AB, 100 mm long, is inclined at 30° to the HP and parallel to the VP. Its end A is in the HP and 30 mm infront of the VP. Draw its projections.
        
        (b) Draw the projections of a regular pentagon of 25 mm side, with its surface making an angle of 45° with HP. One of the sides of the pentagon is parallel to HP and 15 mm away from it.
        
        OR
        
        A rhombus has its diagonals 100 mm and 60 mm long. Draw the projections of the rhombus when it is so placed that its top view appears to be a square of diagonals 60 mm long and the vertical plane through the longer diagonal makes 30 degrees with the VP.
        --- Content provided by FirstRanker.com ---
        
        UNIT - IV
        
        A hexagonal prism, base 30 mm side and axis 75 mm long, has an edge of the base parallel to HP and inclined at 45° to the VP. Its axis makes an angle of 60° with the HP. Draw its projections.
        
        OR
        
        A cone of base diameter 40 mm and slant height 60 mm is kept on the ground on its base. An AIP inclined at 45° to the HP cuts the cone through the midpoint of the axis. Draw the development of remaining portion after removing the cutting portion.
        
        UNIT - V
        --- Content provided by FirstRanker.com ---
        
        Draw the isometric projection of the frustum of a hexagonal pyramid of bottom base side 30 mm and top base side 15 mm having a height of 65 mm. the frustum is resting on HP on its bottom base with one of the edge of the base parallel to VP.
        
        OR
        
        Draw the front view, top view and side view of the block shown in figure below. All dimensions are in mm.
        
        Firstranker's choice
        
        FirstRanker.com
        --- Content provided by‍ FirstRanker.com ---
        
        Code: 15A03101c
        
        B.Tech I Year I Semester (R15) Regular & Supplementary Examinations December 2017
        
        ENGINEERING DRAWING
        
        (Electrical and Electronics Engineering)
        
        Time: 3 hours
        --- Content provided by‌ FirstRanker.com ---
        
        Max. Marks: 70
        
        (Answer all five units, 05 X 14 = 70 Marks)
        
        *****
        
        UNIT - I
        
        Draw an ellipse by oblong method. The major and minor axes given as 150 mm and 90 mm respectively. Draw normal and tangent at any point on the ellipse at a distance of 55 mm from the geometrical center of the ellipse.
        --- Content provided by FirstRanker.com ---
        
        OR
        
        Show by means of a drawing that when the diameter of the directing circle is twice that of the generating circle, the hypocycloid is a straight line. Take the diameter of the generating circle equal to 50 mm.
        
        UNIT - II
        
        The distance between Delhi and Agra is 200 km and its equivalent distance on map measures 10 cm. Draw a diagonal scale to indicate 223 km and 135 km.
        
        OR
        --- Content provided by FirstRanker.com ---
        
        (a) Draw the projections of the following points on the same reference line, keeping the projectors 50 mm apart.
        
        A, in the HP and 30 mm infront of VP.
        
        B, 45 mm below HP and in the VP.
        
        C, 40 mm above HP and 20 infront of the VP.
        
        (b) Two points A and B are in the H.P. The point A is 30 mm in front of the VP, while B is behind the VP. The distance between their projectors is 75 mm and the line joining their top views makes an angle of 45° with xy. Find the distance of the point B from the VP
        
        UNIT - III
        --- Content provided by‌ FirstRanker.com ---
        
        (a) A line AB, 100 mm long, is inclined at 30° to the HP and parallel to the VP. Its end A is in the HP and 30 mm infront of the VP. Draw its projections.
        
        (b) Draw the projections of a regular pentagon of 25 mm side, with its surface making an angle of 45° with HP. One of the sides of the pentagon is parallel to HP and 15 mm away from it.
        
        OR
        
        A rhombus has its diagonals 100 mm and 60 mm long. Draw the projections of the rhombus when it is so placed that its top view appears to be a square of diagonals 60 mm long and the vertical plane through the longer diagonal makes 30 degrees with the VP.
        
        UNIT - IV
        --- Content provided by‍ FirstRanker.com ---
        
        A hexagonal prism, base 30 mm side and axis 75 mm long, has an edge of the base parallel to HP and inclined at 45° to the VP. Its axis makes an angle of 60° with the HP. Draw its projections.
        
        OR
        
        A cone of base diameter 40 mm and slant height 60 mm is kept on the ground on its base. An AIP inclined at 45° to the HP cuts the cone through the midpoint of the axis. Draw the development of remaining portion after removing the cutting portion.
        
        UNIT - V
        
        Draw the isometric projection of the frustum of a hexagonal pyramid of bottom base side 30 mm and top base side 15 mm having a height of 65 mm. the frustum is resting on HP on its bottom base with one of the edge of the base parallel to VP.
        --- Content provided by‌ FirstRanker.com ---
        
        OR
        
        Draw the front view, top view and side view of the block shown in figure below. All dimensions are in mm.
        
        This download link is referred from the post: JNTU Anantapur B-Tech 4-2 last 10 year question papers 2010 -2020 -All regulation- All branches- 4th Year 2nd Sem
        --- Content provided by‍ FirstRanker.com ---
        --- Content provided by FirstRanker.com ---

--- Content provided by‍ FirstRanker.com ---

This post was last modified on 11 September 2020

Get the MBBS Question Bank Android App

Download JNTUA B.Tech 1-1 R15 2017 Dec Supple 15A03101c Engineering Drawing Question Paper

Share This Post:

Share This Post: