GUJARAT TECHNOLOGICAL UNIVERSITY
BE - SEMESTER- VIII (New) EXAMINATION — WINTER 2019
--- Content provided by FirstRanker.com ---
Subject Code: 2182902 Date: 29/11/2019Subject Name: Process & Quality Control in Weaving
Time: 02:30 PM TO 05:00 PM Total Marks: 70
Instructions:
- Attempt all questions.
- Make suitable assumptions wherever necessary.
- Figures to the right indicate full marks.
--- Content provided by FirstRanker.com ---
Q.1 (a) Which loom mechanism/parts affect loom speed? Discuss any two in short. 03
(b) Calculate expected efficiency of a warping machine from following data: 04
Speed: 550 ypm Set length: 18000 m
--- Content provided by FirstRanker.com ---
Yarn length on cheese: 54000 mNo. of ends/beam: 540 End breaks/400 ends/1000 m: 2.4
Time to mend a warp break: 38 sec Time to change a beam: 400 sec
Time to change a creel: 2000 sec
(c) Explain variable staggering of healds and asymmetric shedding tappets. 07
--- Content provided by FirstRanker.com ---
Q.2 (a) Give equation to calculate operative efficiency. 03
(b) Following data is available from slub catcher: 04
No. of objectionable faults : 235 No. of knots put : 174
No. of objectionable faults removed by slub catcher : 65
Calculate clearing efficiency, knot factor and quality factor of the slub catcher.
--- Content provided by FirstRanker.com ---
(c) Explain in detail various quality point about sizing beams. 07
OR
(c) Write in detail on stops on loom due to shuttle change and loss of efficiency due to same. 07
Q.3 (a) What are the control measures related with yarn content on pirn? 03
(b) Discuss on weft tension control in shuttle 04
--- Content provided by FirstRanker.com ---
(c) Write a short note on effect of condition of machine on end breaks at warping. 07
OR
Q.3 (a) Give equation to calculate tension during unwinding of a bobbin. Also discuss effect of each parameter. 03
(b) Explain terms like clearing efficiency, knot factor, relative strength of splice and clearing curve. What is the importance of these terms? 04
(c) Discuss effect of depth of immersion roller, level of size paste and density of ends on average size pick up. 07
--- Content provided by FirstRanker.com ---
Q.4 (a) What is recommended creel tension level for warping? Give value of tension and weight of discs for high speed warping for different count groups. 03
(b) List causes & remedies for patterning damage occurring on wound bobbins. 04
(c) Write a short note on hard waste control in weaving preparatory processes. 07
OR
Q.4 (a) Give sizing-weaving curve and hence discuss how optimum size pick up level is decided? 03
--- Content provided by FirstRanker.com ---
(b) With sketch explain in short use of after waxing. How it helps in improving performance at sizing? 04
Q.5 (a) Write three points to control small weft loop (Phurkies) damage. 03
(b) What are the causes of tightness/slackness in shed connections? How ratio of front and back heald shaft lift is calculated? 04
(c) Discuss in short what special care is required during weaving of Polyester Filament yarn as weft in shuttle looms? 07
--- Content provided by FirstRanker.com ---
OR
Q.5 (a) What are the effects of reed parameters on weaving performance? What is air space? 03
(b) What do you understand by smoothness of shedding in a loom? 04
(c) Write in detail on role of swell release mechanism in shuttle checking. 07
--- Content provided by FirstRanker.com ---
This download link is referred from the post: GTU BE/B.Tech 2019 Winter Question Papers || Gujarat Technological University
--- Content provided by FirstRanker.com ---