Download GTU BE/B.Tech 2018 Winter 4th Sem New 2141403 Materials And Manufacture Of Food Equipment Question Paper

FirstRanker.com

BE - SEMESTER-IV (NEW) EXAMINATION — WINTER 2018

Subject Code: 2141403

--- Content provided by FirstRanker.com ---

Subject Name: Materials & Manufacture of Food Equipment

Date: 05/12/2018

Time: 02:30 PM TO 05:00 PM

Total Marks: 70

Instructions:

--- Content provided by FirstRanker.com ---

1. Attempt all questions.
2. Make suitable assumptions wherever necessary.
3. Figures to the right indicate full marks.

Q1

1. (a) What is the purpose of heat treatment of metals? 03

--- Content provided by FirstRanker.com ---

2. (b) Differentiate between first and third angle of projection. 04
3. (c) Describe the mechanical properties of materials discussing strength, ductility, toughness, stiffness, malleability, plasticity and elasticity. 07

Q2

1. (a) Draw a phase diagram indicating triple point and critical point 03
2. (b) Define stress and strain. Discuss tensile, compressive and shear stress with suitable diagram. 04

--- Content provided by‌ FirstRanker.com ---

3. (c) Draw and describe in detail stress strain curve for material under load. 07

OR

1. (c) Draw the stress strain curve for material exhibiting following properties: 07
   1. (i) Stiff, ductile and strong
   2. (ii) Stiff, brittle and strong
   3. (iii) Stiff, ductile and weak

   --- Content provided by‍ FirstRanker.com ---

   4. (iv) Stiff, brittle and weak
   5. (v) Flexible, brittle and strong
   6. (vi) Flexible, ductile and weak
   7. (vii) Flexible, brittle and weak

--- Content provided by​ FirstRanker.com ---

Q3

1. (a) Show diagrammatically eutectic and peritectic reaction in metals. 03
2. (b) Describe oxy-fuel welding. 04
3. (c) Answer the following with the help of eutectic phase diagram of Sn-Pb alloy shown below: 07
   1. (i) The melting point of Sn and Pb.
   2. (ii) Maximum solubility of Sn in Pb and Pb in Sn.

   --- Content provided by‍ FirstRanker.com ---

   3. (iii) For a 40 wt% Sn—60 wt% Pb alloy at 150°C (300°F),
      1. 1) What phase(s) is (are) present?
      2. 2) What is (are) the composition(s) of the phase(s)?
      3. 3) The relative amount of each phase present?

--- Content provided by‍ FirstRanker.com ---

OR

Q3

1. (a) What are screw threads? 03
2. (b) What are the information present in production drawing? Discuss geometric deviation in brief. 04
3. (c) Write short notes on (i) Pin and cotter joint (ii) Half sectional view (iii) Metric thread 07

--- Content provided by‌ FirstRanker.com ---

Q4

1. (a) Draw the cooling curve of pure iron. 03
2. (b) What are the conventions to draw sectional lines? Draw different types of sectional lines. 04
3. (c) What is annealing? Describe annealing for ferrous and non ferrous metals. 07

OR

--- Content provided by‍ FirstRanker.com ---

Q4

1. (a) What are composite materials? 03
2. (b) Draw a assembly drawing of plate heat exchanger. 04
3. (c) What are natural and synthetic polymers? Describe the mechanism of polymerization. Write the application of polymers in food industry. 07

Q.S

--- Content provided by‍ FirstRanker.com ---

1. (a) What is friction welding? 03
2. (b) Describe the stages of heat treatment process for metals. 04
3. (c) Describe the principle; components and application of 07
   1. (i) Electron beam welding.
   2. (ii) Electric arc welding

--- Content provided by⁠ FirstRanker.com ---

OR

Q.S

1. (a) Enlist the sanitary design features of food contact surfaces. 03
2. (b) Discuss the types of case hardening 04
3. (c) Describe the food equipment standards with regard to surface texture and fabrication. Draw acceptable and unacceptable self-drainage design for tanks and vessels. 07

--- Content provided by FirstRanker.com ---

FirstRanker.com