Download AKTU B-Tech 1st Sem 2015-2016 EC 101 Electronics Engineering Question Paper

Printed Pages: 7.

1258

EC-101

--- Content provided by‌ FirstRanker.com ---

(Following Paper ID and Roll No. to be filled in your Answer Book)

Paper ID: 131111

Roll No.

B.TECH.

(SEM. I) THEORY EXAMINATION, 2015-16

--- Content provided by‍ FirstRanker.com ---

ELECTRONICS ENGINEERING

[Time:3 hours]

[Total Marks:100]

Note: All sections are compulsory.

SECTION-A

--- Content provided by⁠ FirstRanker.com ---

1. Attempt all parts. All parts carry equal marks. Write answer of all part in short. (2x10=20)
   1. What is the purpose of Delay block in CRO?
   2. Define slew rate of an OPAMP.
   3. Why Si is preferred over Ge for manufacturing of electronic devices.
   4. In JFET IDSS=6mA, V_P=-3V biased at V_GS=2V Determine the value of g_m?
   5. Define Op-Amp and Draw its block diagram.

   --- Content provided by‌ FirstRanker.com ---

   6. Explain Common Collector configuration in case of NPN transistor.
   7. Explain ohmic region of the JFET.
   8. What do you understand by 'cut-in' voltage of a diode?
   9. Differentiate between deterministic and random signals.
   10. Define need of unity gain amplifier using an OpAmp.

   --- Content provided by​ FirstRanker.com ---

SECTION-B

Attempt any five questions from this section. (10x5=50)

2. (i) Determine V_o and draw the output waveform of the given network of Figure 1.
   
   

   --- Content provided by FirstRanker.com ---

   (ii) For the network of Figure 2, determine the range of V_I that will maintain V_L at 20 V without exceeding the maximum current rating of 60 mA.
   
3. (i) Determine V_o and I_D for the network of Figure 3.
   
   (ii) Sketch V_o for the network of Figure 4 for the input shown.
   

   --- Content provided by FirstRanker.com ---

4. For the voltage divider configuration of Figure 5 determine r_e, Z_in and Z_o.
   
5. Explain the following with the help of necessary diagrams using an Op-Amp.
   1. Adder
   2. Integrator

   --- Content provided by FirstRanker.com ---

6. (i) Enumerate with the help of a block diagram, various elements involved in Digital Multimeter to measure the various range of Voltage and Current.
   (ii) Explain Differential amplifier in two mode of operation.
7. (i) Determine the output voltage of an op-amp for input voltages of V_i1=100µV and V_i2=120µV. The amplifier has a differential gain of A_d=4000 and the value of CMRR is:
   1. 150
   2. 10³

   --- Content provided by FirstRanker.com ---

   
   (ii) Find V_o for the circuit shown in Figure 6
   
8. With the help of a neat block diagram, explain the working of a CRO and describe the method of measurement of phase and frequency using CRO.
9. Explain with the help of a neat diagram working and characteristic curve of Ramp type digital voltmeter.

--- Content provided by⁠ FirstRanker.com ---

SECTION-C

Attempt any two questions from this section. (15x2=30)

10. (i) Explain the working and characteristic of Tunnel diode with the help of a neat diagram.
    (ii) Describe with the help of circuit diagram, working of a voltage multiplier.
11. (i) Explain construction working and characteristics of P-channel Enhancement type MOSFET.
    

    --- Content provided by FirstRanker.com ---

    (ii) Draw and explain the input and output characteristics.
12. (i) For the common collector configuration in Figure 7, determine I_B, I_C, V_E, V_CE
    
    (ii) Determine Z_i, Z_o and A_v for the circuit of Figure 8. if I_DSS=12mA, V_P=-6V, and Y_o=40 µS.
    

--- Content provided by‍ FirstRanker.com ---

FirstRanker.com