Download AKTU B-Tech 2nd Sem 2015-16 202NME Engineering Machanics Question Paper

Printed Pages: 7

NME-202/NME-102

(Following Paper ID and Roll No. to be filled in your Answer Books)

--- Content provided by‍ FirstRanker.com ---

Paper ID: 199229

Roll No.

B.TECH.

Theory Examination (Semester-II) 2015-16

ENGINEERING MECHANICS

--- Content provided by‍ FirstRanker.com ---

Time: 3 Hours

Max. Marks: 100

Note: This paper having three section attempt question from each section as per instruction.

Section-A

Q1. ATTEPMT ALL PARTS (2×10=20)

1. State the Varignon's theorem. In what conditions it is used?

--- Content provided by​ FirstRanker.com ---

2. A body P is about to slip over body Q. Normal reaction at the contact surface is 120 N and the angle of friction is 14°. Determine the friction force.
3. Explain law of transmissibility of forces
4. Define the relationship between load, shear force and bending moment.
5. Write down the assumptions taken during analysis of truss.
6. Determine the maximum bending moment in a simply supported beam having span of 7m and carrying a point load of 50N at mid of span.

--- Content provided by‍ FirstRanker.com ---

7. Define polar moment of inertia and radius of gyration.
8. Define modulus of rigidity and modulus of elasticity.
9. Define section modulus.
10. Write down the conservation of energy principle.

Section-B

Q2. Attempt any five questions from this section. (5×10=50)

--- Content provided by‍ FirstRanker.com ---

1. Two smooth cylinders of weight P and Q are placed in a smooth channel as shown in figure. Determine the reactions at contact surfaces A, B & C. The following numerical data are given: P=200N, Q=800N, r1=100mm, r2=200mm, and a=400mm, a=45°.
   
   A
   a = 400 mm
   P
   

   --- Content provided by⁠ FirstRanker.com ---

   Q
   D
   B
   C
2. Two blocks having weights W1 and W2 are connected by a string and rest on horizontal planes as shown in figure. If the angle of friction for each block is q, find the magnitude and direction of the least force P applied to the upper block that will induce sliding.
   

   --- Content provided by⁠ FirstRanker.com ---

   
   P
   Q
   W1
   W2

--- Content provided by​ FirstRanker.com ---

3. Analyze the truss as shown in figure. And find magnitude and nature of forces in each member of truss.
   
   2m
   45KN
   D
   

   --- Content provided by FirstRanker.com ---

   E
   2m
   -2m*
   25KN
   TO KN

--- Content provided by‌ FirstRanker.com ---

4. Derive the mass moment of inertia a sphere of radius R about centroidal axis.
5. Determine the co-ordinates of the centroid C of the shaded area as shown in figure.
   
   a
6. The distance covered by a freely falling body in the last 1 second of its motion and that covered in the last but one second are in the ratio of 5:4. Calculate the height from which it strikes the ground.

--- Content provided by FirstRanker.com ---

7. A right circular cylinder of mass m' and radius'r'is suspended from a cord that is wound round its circumference. If the cylinder is allowed to fall freely, find acceleration of its mass centre G and tension in the cord.
   
   .? b
8. Prove that ratio of depth to width to the strongest beam that can be cut circular log of diameter d is v2.

Section-C

Attempt any two question from this section. (2×15=30)

--- Content provided by​ FirstRanker.com ---

1. What are the assumptions taken during derivation of torsion equation. Derive torsion equation
   T/J = t/r = GO/L
2. Calculate the minimum diameter of a solid circular shaft which is not allowed to twist more than 2º in a 5m length when subjected to a torque of 12KN-m. Also calculate the maximum sharing stress developed. Take modulus of rigidity(G)=83 GPa.
3. Draw the shear force and bending moment diagram of the beam as shown in fig and also locate the point of contraflexture.
   
   

   --- Content provided by​ FirstRanker.com ---

   18kN/m
   2101
   2KNIM
   D
   C
   

   --- Content provided by⁠ FirstRanker.com ---

   3m
   2m
   -24
   RB
4. Calculate the moment of inertia of composite section as shown in figure about its centroidal axis.
   

   --- Content provided by​ FirstRanker.com ---

   
   Y
   30m
   mm
   B
   

   --- Content provided by FirstRanker.com ---

   *30mm
   X

Visit FirstRanker.com for more information.