Download JNTUK (Jawaharlal Nehru Technological University Kakinada) B.Tech 2-2 (2nd Year 2nd Sem) HYDRAULICS AND HYDRAULIC MACHINERY Question Paper.
|''|''|||''|'''|||'|
Code No: R22014
II B. Tech II Semester Regular Examinations, August? 2014
HYDRAULICS AND HYDRAULIC MACHINERY
(Civil Engineering)
Time: 3 hours Max. Marks: 75
Answer any FIVE Questions
All Questions carry Equal Marks
~~~~~~~~~~~~~~~~~~~~~~~~
1. a) Explain the terms: i) specific energy ii) critical depth and iii) Critical velocity.
b) In a rectangular open channel of 5 m width the flow rate is 12 m
3
/s and depth of flow is
1.0 m. Determine the critical depth and the alternate depth. (6M+9M)
2. a) Explain the term hydraulic jump. Derive an expression for the downstream depth of
hydraulic jump.
b) Define specific energy and draw the specific energy diagram. Explain how it is useful for
the open channel flow. (8M+7M)
3. Assuming that the viscous force F exerted by a fluid on a sphere of diameter D depends on the
viscosity ?, mass density of the fluid ???, and the velocity of the sphere ?, obtain and
expression for the viscous force. (15M)
4. a) Obtain an expression for the force exerted by a jet of water on a fixed vertical plate in the
direction of the jet.
b) A jet of water of diameter 100 mm moving with a velocity of 35 m/s strikes a curved fixed
symmetrical plate at the center. Find the force exerted by the jet of water in the direction of
the jet, if the jet is deflected through an angle of 120? at the outlet of the curved plate.
(7M+8M)
5. a) Explain how hydraulic turbines are classified.
b) Explain briefly the principles on which a Kaplan turbine works. (7M+8M)
6. a) What is cavitation? How can it be avoided in reaction turbine?
b) What is the basis of selection of a turbine at a particular place? (8M+7M)
7. Define a centrifugal pump. Explain the working of a single stage centrifugal pump with neat
sketches. (15M)
8. Write short notes on the following:
a) Firm Power
b) Secondary power
c) Diversity factor
d) Load duration curve. (15M)
1of 1
R10
SET - 1
FirstRanker.com - FirstRanker's Choice
FirstRanker.com
|''|''|||''|'''|||'|
Code No: R22014
II B. Tech II Semester Regular Examinations, August? 2014
HYDRAULICS AND HYDRAULIC MACHINERY
(Civil Engineering)
Time: 3 hours Max. Marks: 75
Answer any FIVE Questions
All Questions carry Equal Marks
~~~~~~~~~~~~~~~~~~~~~~~~
1. a) Explain the terms: i) specific energy ii) critical depth and iii) Critical velocity.
b) In a rectangular open channel of 5 m width the flow rate is 12 m
3
/s and depth of flow is
1.0 m. Determine the critical depth and the alternate depth. (6M+9M)
2. a) Explain the term hydraulic jump. Derive an expression for the downstream depth of
hydraulic jump.
b) Define specific energy and draw the specific energy diagram. Explain how it is useful for
the open channel flow. (8M+7M)
3. Assuming that the viscous force F exerted by a fluid on a sphere of diameter D depends on the
viscosity ?, mass density of the fluid ???, and the velocity of the sphere ?, obtain and
expression for the viscous force. (15M)
4. a) Obtain an expression for the force exerted by a jet of water on a fixed vertical plate in the
direction of the jet.
b) A jet of water of diameter 100 mm moving with a velocity of 35 m/s strikes a curved fixed
symmetrical plate at the center. Find the force exerted by the jet of water in the direction of
the jet, if the jet is deflected through an angle of 120? at the outlet of the curved plate.
(7M+8M)
5. a) Explain how hydraulic turbines are classified.
b) Explain briefly the principles on which a Kaplan turbine works. (7M+8M)
6. a) What is cavitation? How can it be avoided in reaction turbine?
b) What is the basis of selection of a turbine at a particular place? (8M+7M)
7. Define a centrifugal pump. Explain the working of a single stage centrifugal pump with neat
sketches. (15M)
8. Write short notes on the following:
a) Firm Power
b) Secondary power
c) Diversity factor
d) Load duration curve. (15M)
1of 1
R10
SET - 1
FirstRanker.com
|''|''|||''|'''|||'|
Code No: R22014
II B. Tech II Semester Regular Examinations, August? 2014
HYDRAULICS AND HYDRAULIC MACHINERY
(Civil Engineering)
Time: 3 hours Max. Marks: 75
Answer any FIVE Questions
All Questions carry Equal Marks
~~~~~~~~~~~~~~~~~~~~~~~~
1. a) Derive the condition for depth of flow of a most economical circular channel section subject
to the condition for maximum velocity.
b) Determine the economical cross-section for an open channel of trapezoidal section with side
slopes of 1 vertical to 2 horizontal, to carry 12 m
3
/s, the bed slope being 1/2100. Assume
Manning coefficient as 0.022. (7M+8M)
2. Define specific energy? Sketch the specific energy curve and explain regimes of flow? Indicate
the features of critical flow? Deduce the condition for minimum specific energy and the related
expressions in rectangular channels? (15M)
3. a) Explain different types of hydraulic similarities that must exist between a prototype and its
model.
b) Explain the terms: distorted models and undistorted models. What is the use of distorted
models? (7M+8M)
4. a) Derive the expression for the force exerted by a water jet on a plate moving in the same
direction of the jet with a velocity less than that of the jet.
b) A blade turns the jet of diameter 2.5cm at a velocity of 25 m/s by 60?. Determine the force
exerted by the blade on the fluid. (8M+7M)
5. a) What are the main differences between impulse and reaction turbines?
b) List the various efficiencies used to express the performance of hydraulic turbines.
(7M+8M)
6. a) What are unit quantities? Define the unit quantities for turbine.
b) By means of a neat sketch explain the governing mechanism of Francis turbine. (7M+8M)
7. What do you mean by manometric efficiency, mechanical efficiency and overall efficiency of
centrifugal pump? (15M)
8. a) What is meant by flow duration curve and power duration curve? How do you differentiate
these? How would you construct such curves?
b) Explain how hydropower plants are classified. (8M+7M)
1 of 1
R10
SET - 2
FirstRanker.com - FirstRanker's Choice
FirstRanker.com
|''|''|||''|'''|||'|
Code No: R22014
II B. Tech II Semester Regular Examinations, August? 2014
HYDRAULICS AND HYDRAULIC MACHINERY
(Civil Engineering)
Time: 3 hours Max. Marks: 75
Answer any FIVE Questions
All Questions carry Equal Marks
~~~~~~~~~~~~~~~~~~~~~~~~
1. a) Explain the terms: i) specific energy ii) critical depth and iii) Critical velocity.
b) In a rectangular open channel of 5 m width the flow rate is 12 m
3
/s and depth of flow is
1.0 m. Determine the critical depth and the alternate depth. (6M+9M)
2. a) Explain the term hydraulic jump. Derive an expression for the downstream depth of
hydraulic jump.
b) Define specific energy and draw the specific energy diagram. Explain how it is useful for
the open channel flow. (8M+7M)
3. Assuming that the viscous force F exerted by a fluid on a sphere of diameter D depends on the
viscosity ?, mass density of the fluid ???, and the velocity of the sphere ?, obtain and
expression for the viscous force. (15M)
4. a) Obtain an expression for the force exerted by a jet of water on a fixed vertical plate in the
direction of the jet.
b) A jet of water of diameter 100 mm moving with a velocity of 35 m/s strikes a curved fixed
symmetrical plate at the center. Find the force exerted by the jet of water in the direction of
the jet, if the jet is deflected through an angle of 120? at the outlet of the curved plate.
(7M+8M)
5. a) Explain how hydraulic turbines are classified.
b) Explain briefly the principles on which a Kaplan turbine works. (7M+8M)
6. a) What is cavitation? How can it be avoided in reaction turbine?
b) What is the basis of selection of a turbine at a particular place? (8M+7M)
7. Define a centrifugal pump. Explain the working of a single stage centrifugal pump with neat
sketches. (15M)
8. Write short notes on the following:
a) Firm Power
b) Secondary power
c) Diversity factor
d) Load duration curve. (15M)
1of 1
R10
SET - 1
FirstRanker.com
|''|''|||''|'''|||'|
Code No: R22014
II B. Tech II Semester Regular Examinations, August? 2014
HYDRAULICS AND HYDRAULIC MACHINERY
(Civil Engineering)
Time: 3 hours Max. Marks: 75
Answer any FIVE Questions
All Questions carry Equal Marks
~~~~~~~~~~~~~~~~~~~~~~~~
1. a) Derive the condition for depth of flow of a most economical circular channel section subject
to the condition for maximum velocity.
b) Determine the economical cross-section for an open channel of trapezoidal section with side
slopes of 1 vertical to 2 horizontal, to carry 12 m
3
/s, the bed slope being 1/2100. Assume
Manning coefficient as 0.022. (7M+8M)
2. Define specific energy? Sketch the specific energy curve and explain regimes of flow? Indicate
the features of critical flow? Deduce the condition for minimum specific energy and the related
expressions in rectangular channels? (15M)
3. a) Explain different types of hydraulic similarities that must exist between a prototype and its
model.
b) Explain the terms: distorted models and undistorted models. What is the use of distorted
models? (7M+8M)
4. a) Derive the expression for the force exerted by a water jet on a plate moving in the same
direction of the jet with a velocity less than that of the jet.
b) A blade turns the jet of diameter 2.5cm at a velocity of 25 m/s by 60?. Determine the force
exerted by the blade on the fluid. (8M+7M)
5. a) What are the main differences between impulse and reaction turbines?
b) List the various efficiencies used to express the performance of hydraulic turbines.
(7M+8M)
6. a) What are unit quantities? Define the unit quantities for turbine.
b) By means of a neat sketch explain the governing mechanism of Francis turbine. (7M+8M)
7. What do you mean by manometric efficiency, mechanical efficiency and overall efficiency of
centrifugal pump? (15M)
8. a) What is meant by flow duration curve and power duration curve? How do you differentiate
these? How would you construct such curves?
b) Explain how hydropower plants are classified. (8M+7M)
1 of 1
R10
SET - 2
FirstRanker.com
|''|''|||''|'''|||'|
Code No: R22014
II B. Tech II Semester Regular Examinations, August? 2014
HYDRAULICS AND HYDRAULIC MACHINERY
(Civil Engineering)
Time: 3 hours Max. Marks: 75
Answer any FIVE Questions
All Questions carry Equal Marks
~~~~~~~~~~~~~~~~~~~~~~~~
1. a) Explain the terms specific energy of a flowing liquid, minimum specific energy, critical
depth, critical velocity and alternate depths as applied to non-uniform flow.
b) A trapezoidal channel has a bed width of 5 m, side slopes of 1 upon 1.5 and Manning?s
n = 0.016. Compute the critical slope and the corresponding discharge for a critical depth of
2 m (7M+8M)
2. a) Define a back water curve and derive an expression for finding the length of the back water
curve.
b) A rectangular channel of 5 m width discharges water at the rate of 1.6 m
3
/s into a 5 m wide
apron with 1/2800 slope at a velocity of 5 m/s. Determine the height of the hydraulic jump
and energy loss. (7M+8M)
3. What do you mean by dimensional numbers? Name any four dimensional numbers. Define and
explain Reynold?s number, Froude?s number and Mach number. Derive expressions for any
above two numbers. (15M)
4. a) Show that the force exerted by a jet of water on an inclined fixed plate in the direction of the
jet is given by F
x
=? aV
2
sin
2
?, where a= Area of the jet, V=velocity of the jet and
?=inclination of the plate with the jet.
b) A blade turns the jet of diameter 3 cm at a velocity of 20 m/s by 60?. Determine the force
exerted by the blade on the fluid. (7M+8M)
5. a) What is draft tube? What are its functions?
b) Describe functions of various main components of Pelton turbine with neat sketch (7M+8M)
6. a) What do you mean by surge tank? What are different types of surge tanks?
b) Explain various characteristics curves of a hydraulic turbine. (8M+7M)
7. Define a centrifugal pump. Explain the working of a single stage centrifugal pump with neat
sketches. (15M)
8. a) How do you estimate hydropower potential
b) List out twelve important hydropower plants in India. (7M+8M)
1 of 1
R10
SET - 3
FirstRanker.com - FirstRanker's Choice
FirstRanker.com
|''|''|||''|'''|||'|
Code No: R22014
II B. Tech II Semester Regular Examinations, August? 2014
HYDRAULICS AND HYDRAULIC MACHINERY
(Civil Engineering)
Time: 3 hours Max. Marks: 75
Answer any FIVE Questions
All Questions carry Equal Marks
~~~~~~~~~~~~~~~~~~~~~~~~
1. a) Explain the terms: i) specific energy ii) critical depth and iii) Critical velocity.
b) In a rectangular open channel of 5 m width the flow rate is 12 m
3
/s and depth of flow is
1.0 m. Determine the critical depth and the alternate depth. (6M+9M)
2. a) Explain the term hydraulic jump. Derive an expression for the downstream depth of
hydraulic jump.
b) Define specific energy and draw the specific energy diagram. Explain how it is useful for
the open channel flow. (8M+7M)
3. Assuming that the viscous force F exerted by a fluid on a sphere of diameter D depends on the
viscosity ?, mass density of the fluid ???, and the velocity of the sphere ?, obtain and
expression for the viscous force. (15M)
4. a) Obtain an expression for the force exerted by a jet of water on a fixed vertical plate in the
direction of the jet.
b) A jet of water of diameter 100 mm moving with a velocity of 35 m/s strikes a curved fixed
symmetrical plate at the center. Find the force exerted by the jet of water in the direction of
the jet, if the jet is deflected through an angle of 120? at the outlet of the curved plate.
(7M+8M)
5. a) Explain how hydraulic turbines are classified.
b) Explain briefly the principles on which a Kaplan turbine works. (7M+8M)
6. a) What is cavitation? How can it be avoided in reaction turbine?
b) What is the basis of selection of a turbine at a particular place? (8M+7M)
7. Define a centrifugal pump. Explain the working of a single stage centrifugal pump with neat
sketches. (15M)
8. Write short notes on the following:
a) Firm Power
b) Secondary power
c) Diversity factor
d) Load duration curve. (15M)
1of 1
R10
SET - 1
FirstRanker.com
|''|''|||''|'''|||'|
Code No: R22014
II B. Tech II Semester Regular Examinations, August? 2014
HYDRAULICS AND HYDRAULIC MACHINERY
(Civil Engineering)
Time: 3 hours Max. Marks: 75
Answer any FIVE Questions
All Questions carry Equal Marks
~~~~~~~~~~~~~~~~~~~~~~~~
1. a) Derive the condition for depth of flow of a most economical circular channel section subject
to the condition for maximum velocity.
b) Determine the economical cross-section for an open channel of trapezoidal section with side
slopes of 1 vertical to 2 horizontal, to carry 12 m
3
/s, the bed slope being 1/2100. Assume
Manning coefficient as 0.022. (7M+8M)
2. Define specific energy? Sketch the specific energy curve and explain regimes of flow? Indicate
the features of critical flow? Deduce the condition for minimum specific energy and the related
expressions in rectangular channels? (15M)
3. a) Explain different types of hydraulic similarities that must exist between a prototype and its
model.
b) Explain the terms: distorted models and undistorted models. What is the use of distorted
models? (7M+8M)
4. a) Derive the expression for the force exerted by a water jet on a plate moving in the same
direction of the jet with a velocity less than that of the jet.
b) A blade turns the jet of diameter 2.5cm at a velocity of 25 m/s by 60?. Determine the force
exerted by the blade on the fluid. (8M+7M)
5. a) What are the main differences between impulse and reaction turbines?
b) List the various efficiencies used to express the performance of hydraulic turbines.
(7M+8M)
6. a) What are unit quantities? Define the unit quantities for turbine.
b) By means of a neat sketch explain the governing mechanism of Francis turbine. (7M+8M)
7. What do you mean by manometric efficiency, mechanical efficiency and overall efficiency of
centrifugal pump? (15M)
8. a) What is meant by flow duration curve and power duration curve? How do you differentiate
these? How would you construct such curves?
b) Explain how hydropower plants are classified. (8M+7M)
1 of 1
R10
SET - 2
FirstRanker.com
|''|''|||''|'''|||'|
Code No: R22014
II B. Tech II Semester Regular Examinations, August? 2014
HYDRAULICS AND HYDRAULIC MACHINERY
(Civil Engineering)
Time: 3 hours Max. Marks: 75
Answer any FIVE Questions
All Questions carry Equal Marks
~~~~~~~~~~~~~~~~~~~~~~~~
1. a) Explain the terms specific energy of a flowing liquid, minimum specific energy, critical
depth, critical velocity and alternate depths as applied to non-uniform flow.
b) A trapezoidal channel has a bed width of 5 m, side slopes of 1 upon 1.5 and Manning?s
n = 0.016. Compute the critical slope and the corresponding discharge for a critical depth of
2 m (7M+8M)
2. a) Define a back water curve and derive an expression for finding the length of the back water
curve.
b) A rectangular channel of 5 m width discharges water at the rate of 1.6 m
3
/s into a 5 m wide
apron with 1/2800 slope at a velocity of 5 m/s. Determine the height of the hydraulic jump
and energy loss. (7M+8M)
3. What do you mean by dimensional numbers? Name any four dimensional numbers. Define and
explain Reynold?s number, Froude?s number and Mach number. Derive expressions for any
above two numbers. (15M)
4. a) Show that the force exerted by a jet of water on an inclined fixed plate in the direction of the
jet is given by F
x
=? aV
2
sin
2
?, where a= Area of the jet, V=velocity of the jet and
?=inclination of the plate with the jet.
b) A blade turns the jet of diameter 3 cm at a velocity of 20 m/s by 60?. Determine the force
exerted by the blade on the fluid. (7M+8M)
5. a) What is draft tube? What are its functions?
b) Describe functions of various main components of Pelton turbine with neat sketch (7M+8M)
6. a) What do you mean by surge tank? What are different types of surge tanks?
b) Explain various characteristics curves of a hydraulic turbine. (8M+7M)
7. Define a centrifugal pump. Explain the working of a single stage centrifugal pump with neat
sketches. (15M)
8. a) How do you estimate hydropower potential
b) List out twelve important hydropower plants in India. (7M+8M)
1 of 1
R10
SET - 3
FirstRanker.com
|''|''|||''|'''|||'|
Code No: R22014
II B. Tech II Semester Regular Examinations, August? 2014
HYDRAULICS AND HYDRAULIC MACHINERY
(Civil Engineering)
Time: 3 hours Max. Marks: 75
Answer any FIVE Questions
All Questions carry Equal Marks
~~~~~~~~~~~~~~~~~~~~~~~~
1. a) Derive the condition for the best side slope of the most economical trapezoidal channel.
b) Using Bazins formula, determine the discharge through a rectangular ordinary earthen
channel 2 m wide and 0.6 m deep with a slope of l in 2600. Assume Bazins constant
k = 1.303. If Manning constant for this type is 0.025, determine and compare the flow.
(7M+8M)
2. a) Define hydraulic jump and explain under what circumstances it occurs
b) Obtain an expression for the depth after the hydraulic jump and the loss of head due to the
jump. Write the assumptions made. (7M+8M)
3. State Buckingham?s ?-theorem. Why this theorem is considered superior over the Rayleigh?s
method for dimensional analysis. (15M)
4. a) Define the terms: i) Impact of jets, and ii) Jet propulsion.
b) A jet of water of diameter 55 mm moving with a velocity of 20 m/s strikes a fixed plate in
such a way that the angle between the jet and the plate is 60?. Find the force exerted by the
jet on the plate i) in the direction normal to the plate, and ii) in the direction of the jet.
(6M+9M)
5. a) How will you classify the turbines?
b) Differentiate between turbines and pumps. (7M+8M)
6. What do you understand by the characteristics curves of turbine? Name the important
characteristics of a turbine. (15M)
7. Draw and discuss the operating characteristics of a centrifugal pump (15M)
8. a) What are the main components of hydropower plants and explain each in detail
b) Define the terms: i) load factor, ii) utilization factor and iii) capacity factor
(8M+7M)
1 of 1
R10
SET - 4
FirstRanker.com - FirstRanker's Choice
This post was last modified on 03 December 2019