Download GATE (Graduate Aptitude Test in Engineering) Last 10 Years 2020, 2019, 2018, 2017, 2016, 2015, 2014, 2013, 2012, 2011 and 2010 AE Aerospace Engineering Question Paper With Solution And Answer Key
GA 1/3
Q. 1 ? Q. 5 carry one mark each.
Q.1 ?The dress _________ her so well that they all immediately _________ her on her
appearance.?
The words that best fill the blanks in the above sentence are
(A) complemented, complemented (B) complimented, complemented
(C) complimented, complimented (D) complemented, complimented
Q.2 ?The judge?s standing in the legal community, though shaken by false allegations of
wrongdoing, remained _________.?
The word that best fills the blank in the above sentence is
(A) undiminished (B) damaged (C) illegal (D) uncertain
Q.3 Find the missing group of letters in the following series:
BC, FGH, LMNO, _____
(A) UVWXY (B) TUVWX (C) STUVW (D) RSTUV
Q.4 The perimeters of a circle, a square and an equilateral triangle are equal. Which one of the
following statements is true?
(A) The circle has the largest area.
(B) The square has the largest area.
(C) The equilateral triangle has the largest area.
(D) All the three shapes have the same area.
Q.5
The value of the expression
1
1 + log
?? ????
+
1
1 + log
?? ????
+
1
1 + log
?? ????
is _________.
(A) -1 (B) 0 (C) 1 (D) 3
Q. 6 ? Q. 10 carry two marks each.
Q.6 Forty students watched films A, B and C over a week. Each student watched either only
one film or all three. Thirteen students watched film A, sixteen students watched film B
and nineteen students watched film C. How many students watched all three films?
(A) 0 (B) 2 (C) 4 (D) 8
FirstRanker.com - FirstRanker's Choice
GATE 2018 General Aptitude (GA) Set-2
GA 1/3
Q. 1 ? Q. 5 carry one mark each.
Q.1 ?The dress _________ her so well that they all immediately _________ her on her
appearance.?
The words that best fill the blanks in the above sentence are
(A) complemented, complemented (B) complimented, complemented
(C) complimented, complimented (D) complemented, complimented
Q.2 ?The judge?s standing in the legal community, though shaken by false allegations of
wrongdoing, remained _________.?
The word that best fills the blank in the above sentence is
(A) undiminished (B) damaged (C) illegal (D) uncertain
Q.3 Find the missing group of letters in the following series:
BC, FGH, LMNO, _____
(A) UVWXY (B) TUVWX (C) STUVW (D) RSTUV
Q.4 The perimeters of a circle, a square and an equilateral triangle are equal. Which one of the
following statements is true?
(A) The circle has the largest area.
(B) The square has the largest area.
(C) The equilateral triangle has the largest area.
(D) All the three shapes have the same area.
Q.5
The value of the expression
1
1 + log
?? ????
+
1
1 + log
?? ????
+
1
1 + log
?? ????
is _________.
(A) -1 (B) 0 (C) 1 (D) 3
Q. 6 ? Q. 10 carry two marks each.
Q.6 Forty students watched films A, B and C over a week. Each student watched either only
one film or all three. Thirteen students watched film A, sixteen students watched film B
and nineteen students watched film C. How many students watched all three films?
(A) 0 (B) 2 (C) 4 (D) 8
GATE 2018 General Aptitude (GA) Set-2
GA 2/3
Q.7 A wire would enclose an area of 1936 m
2
, if it is bent into a square. The wire is cut into
two pieces. The longer piece is thrice as long as the shorter piece. The long and the short
pieces are bent into a square and a circle, respectively. Which of the following choices is
closest to the sum of the areas enclosed by the two pieces in square meters?
(A) 1096 (B) 1111 (C) 1243 (D) 2486
Q.8 A contract is to be completed in 52 days and 125 identical robots were employed, each
operational for 7 hours a day. After 39 days, five-seventh of the work was completed. How
many additional robots would be required to complete the work on time, if each robot is
now operational for 8 hours a day?
(A) 50 (B) 89 (C) 146 (D) 175
Q.9 A house has a number which needs to be identified. The following three statements are
given that can help in identifying the house number.
i. If the house number is a multiple of 3, then it is a number from 50 to 59.
ii. If the house number is NOT a multiple of 4, then it is a number from 60 to 69.
iii. If the house number is NOT a multiple of 6, then it is a number from 70 to 79.
What is the house number?
(A) 54 (B) 65 (C) 66 (D) 76
FirstRanker.com - FirstRanker's Choice
GATE 2018 General Aptitude (GA) Set-2
GA 1/3
Q. 1 ? Q. 5 carry one mark each.
Q.1 ?The dress _________ her so well that they all immediately _________ her on her
appearance.?
The words that best fill the blanks in the above sentence are
(A) complemented, complemented (B) complimented, complemented
(C) complimented, complimented (D) complemented, complimented
Q.2 ?The judge?s standing in the legal community, though shaken by false allegations of
wrongdoing, remained _________.?
The word that best fills the blank in the above sentence is
(A) undiminished (B) damaged (C) illegal (D) uncertain
Q.3 Find the missing group of letters in the following series:
BC, FGH, LMNO, _____
(A) UVWXY (B) TUVWX (C) STUVW (D) RSTUV
Q.4 The perimeters of a circle, a square and an equilateral triangle are equal. Which one of the
following statements is true?
(A) The circle has the largest area.
(B) The square has the largest area.
(C) The equilateral triangle has the largest area.
(D) All the three shapes have the same area.
Q.5
The value of the expression
1
1 + log
?? ????
+
1
1 + log
?? ????
+
1
1 + log
?? ????
is _________.
(A) -1 (B) 0 (C) 1 (D) 3
Q. 6 ? Q. 10 carry two marks each.
Q.6 Forty students watched films A, B and C over a week. Each student watched either only
one film or all three. Thirteen students watched film A, sixteen students watched film B
and nineteen students watched film C. How many students watched all three films?
(A) 0 (B) 2 (C) 4 (D) 8
GATE 2018 General Aptitude (GA) Set-2
GA 2/3
Q.7 A wire would enclose an area of 1936 m
2
, if it is bent into a square. The wire is cut into
two pieces. The longer piece is thrice as long as the shorter piece. The long and the short
pieces are bent into a square and a circle, respectively. Which of the following choices is
closest to the sum of the areas enclosed by the two pieces in square meters?
(A) 1096 (B) 1111 (C) 1243 (D) 2486
Q.8 A contract is to be completed in 52 days and 125 identical robots were employed, each
operational for 7 hours a day. After 39 days, five-seventh of the work was completed. How
many additional robots would be required to complete the work on time, if each robot is
now operational for 8 hours a day?
(A) 50 (B) 89 (C) 146 (D) 175
Q.9 A house has a number which needs to be identified. The following three statements are
given that can help in identifying the house number.
i. If the house number is a multiple of 3, then it is a number from 50 to 59.
ii. If the house number is NOT a multiple of 4, then it is a number from 60 to 69.
iii. If the house number is NOT a multiple of 6, then it is a number from 70 to 79.
What is the house number?
(A) 54 (B) 65 (C) 66 (D) 76
GATE 2018 General Aptitude (GA) Set-2
GA 3/3
Q.10 An unbiased coin is tossed six times in a row and four different such trials are conducted.
One trial implies six tosses of the coin. If H stands for head and T stands for tail, the
following are the observations from the four trials:
(1) HTHTHT (2) TTHHHT (3) HTTHHT (4) HHHT__ __.
Which statement describing the last two coin tosses of the fourth trial has the highest
probability of being correct?
(A) Two T will occur.
(B) One H and one T will occur.
(C) Two H will occur.
(D) One H will be followed by one T.
END OF THE QUESTION PAPER
FirstRanker.com - FirstRanker's Choice
GATE 2018 General Aptitude (GA) Set-2
GA 1/3
Q. 1 ? Q. 5 carry one mark each.
Q.1 ?The dress _________ her so well that they all immediately _________ her on her
appearance.?
The words that best fill the blanks in the above sentence are
(A) complemented, complemented (B) complimented, complemented
(C) complimented, complimented (D) complemented, complimented
Q.2 ?The judge?s standing in the legal community, though shaken by false allegations of
wrongdoing, remained _________.?
The word that best fills the blank in the above sentence is
(A) undiminished (B) damaged (C) illegal (D) uncertain
Q.3 Find the missing group of letters in the following series:
BC, FGH, LMNO, _____
(A) UVWXY (B) TUVWX (C) STUVW (D) RSTUV
Q.4 The perimeters of a circle, a square and an equilateral triangle are equal. Which one of the
following statements is true?
(A) The circle has the largest area.
(B) The square has the largest area.
(C) The equilateral triangle has the largest area.
(D) All the three shapes have the same area.
Q.5
The value of the expression
1
1 + log
?? ????
+
1
1 + log
?? ????
+
1
1 + log
?? ????
is _________.
(A) -1 (B) 0 (C) 1 (D) 3
Q. 6 ? Q. 10 carry two marks each.
Q.6 Forty students watched films A, B and C over a week. Each student watched either only
one film or all three. Thirteen students watched film A, sixteen students watched film B
and nineteen students watched film C. How many students watched all three films?
(A) 0 (B) 2 (C) 4 (D) 8
GATE 2018 General Aptitude (GA) Set-2
GA 2/3
Q.7 A wire would enclose an area of 1936 m
2
, if it is bent into a square. The wire is cut into
two pieces. The longer piece is thrice as long as the shorter piece. The long and the short
pieces are bent into a square and a circle, respectively. Which of the following choices is
closest to the sum of the areas enclosed by the two pieces in square meters?
(A) 1096 (B) 1111 (C) 1243 (D) 2486
Q.8 A contract is to be completed in 52 days and 125 identical robots were employed, each
operational for 7 hours a day. After 39 days, five-seventh of the work was completed. How
many additional robots would be required to complete the work on time, if each robot is
now operational for 8 hours a day?
(A) 50 (B) 89 (C) 146 (D) 175
Q.9 A house has a number which needs to be identified. The following three statements are
given that can help in identifying the house number.
i. If the house number is a multiple of 3, then it is a number from 50 to 59.
ii. If the house number is NOT a multiple of 4, then it is a number from 60 to 69.
iii. If the house number is NOT a multiple of 6, then it is a number from 70 to 79.
What is the house number?
(A) 54 (B) 65 (C) 66 (D) 76
GATE 2018 General Aptitude (GA) Set-2
GA 3/3
Q.10 An unbiased coin is tossed six times in a row and four different such trials are conducted.
One trial implies six tosses of the coin. If H stands for head and T stands for tail, the
following are the observations from the four trials:
(1) HTHTHT (2) TTHHHT (3) HTTHHT (4) HHHT__ __.
Which statement describing the last two coin tosses of the fourth trial has the highest
probability of being correct?
(A) Two T will occur.
(B) One H and one T will occur.
(C) Two H will occur.
(D) One H will be followed by one T.
END OF THE QUESTION PAPER
GATE 2018 Aerospace Engineering
AE 1/9
Q. 1 ? Q. 25 carry one mark each.
Q.1
Let ?? ? , ?? ? ?
be two distinct vectors that are not parallel. The vector ?? ? = ?? ? ? ?? ? ?
is
(A) zero. (B) orthogonal to ?? ? alone.
(C) orthogonal to ?? ? + ?? ? ?
. (D) orthogonal to ?? ? ?
alone.
Q.2
Consider the function ?? (?? , ?? ) =
?? 2
2
+
?? 2
3
? 5. All the roots of this function
(A) form a finite set of points.
(B) lie on an elliptical curve.
(C) lie on the surface of a sphere.
(D) lie on a hyperbolic curve.
Q.3
Consider a vector field given by ?? ?? ? + ?? ?? ? + ?? ?? ?
. This vector field is
(A) divergence-free and curl-free.
(B) curl-free but not divergence-free.
(C) divergence-free but not curl-free.
(D) neither divergence-free nor curl-free.
Q.4 A jet aircraft is initially flying steady and level at its maximum endurance condition. For the
aircraft to fly steady and level, but faster at the same altitude, the pilot should
(A) increase thrust alone.
(B) increase thrust and increase angle of attack.
(C) increase thrust and reduce angle of attack.
(D) reduce angle of attack alone.
Q.5 The pilot of a conventional airplane that is flying steady and level at some altitude, deflects
the port side aileron up and the starboard aileron down. The aircraft will then
(A) pitch, nose up.
(B) roll with the starboard wing up.
(C) pitch, nose down.
(D) roll with the port wing up.
Q.6 A NACA 0012 airfoil has a trailing edge flap. The airfoil is operating at an angle of attack
of 5 degrees with un-deflected flap. If the flap is now deflected by 5 degrees downwards, the
?? ?? versus ?? curve
(A) shifts right and slope increases.
(B) shifts left and slope increases.
(C) shifts left and slope stays the same.
(D) shifts right and slope stays the same.
FirstRanker.com - FirstRanker's Choice
GATE 2018 General Aptitude (GA) Set-2
GA 1/3
Q. 1 ? Q. 5 carry one mark each.
Q.1 ?The dress _________ her so well that they all immediately _________ her on her
appearance.?
The words that best fill the blanks in the above sentence are
(A) complemented, complemented (B) complimented, complemented
(C) complimented, complimented (D) complemented, complimented
Q.2 ?The judge?s standing in the legal community, though shaken by false allegations of
wrongdoing, remained _________.?
The word that best fills the blank in the above sentence is
(A) undiminished (B) damaged (C) illegal (D) uncertain
Q.3 Find the missing group of letters in the following series:
BC, FGH, LMNO, _____
(A) UVWXY (B) TUVWX (C) STUVW (D) RSTUV
Q.4 The perimeters of a circle, a square and an equilateral triangle are equal. Which one of the
following statements is true?
(A) The circle has the largest area.
(B) The square has the largest area.
(C) The equilateral triangle has the largest area.
(D) All the three shapes have the same area.
Q.5
The value of the expression
1
1 + log
?? ????
+
1
1 + log
?? ????
+
1
1 + log
?? ????
is _________.
(A) -1 (B) 0 (C) 1 (D) 3
Q. 6 ? Q. 10 carry two marks each.
Q.6 Forty students watched films A, B and C over a week. Each student watched either only
one film or all three. Thirteen students watched film A, sixteen students watched film B
and nineteen students watched film C. How many students watched all three films?
(A) 0 (B) 2 (C) 4 (D) 8
GATE 2018 General Aptitude (GA) Set-2
GA 2/3
Q.7 A wire would enclose an area of 1936 m
2
, if it is bent into a square. The wire is cut into
two pieces. The longer piece is thrice as long as the shorter piece. The long and the short
pieces are bent into a square and a circle, respectively. Which of the following choices is
closest to the sum of the areas enclosed by the two pieces in square meters?
(A) 1096 (B) 1111 (C) 1243 (D) 2486
Q.8 A contract is to be completed in 52 days and 125 identical robots were employed, each
operational for 7 hours a day. After 39 days, five-seventh of the work was completed. How
many additional robots would be required to complete the work on time, if each robot is
now operational for 8 hours a day?
(A) 50 (B) 89 (C) 146 (D) 175
Q.9 A house has a number which needs to be identified. The following three statements are
given that can help in identifying the house number.
i. If the house number is a multiple of 3, then it is a number from 50 to 59.
ii. If the house number is NOT a multiple of 4, then it is a number from 60 to 69.
iii. If the house number is NOT a multiple of 6, then it is a number from 70 to 79.
What is the house number?
(A) 54 (B) 65 (C) 66 (D) 76
GATE 2018 General Aptitude (GA) Set-2
GA 3/3
Q.10 An unbiased coin is tossed six times in a row and four different such trials are conducted.
One trial implies six tosses of the coin. If H stands for head and T stands for tail, the
following are the observations from the four trials:
(1) HTHTHT (2) TTHHHT (3) HTTHHT (4) HHHT__ __.
Which statement describing the last two coin tosses of the fourth trial has the highest
probability of being correct?
(A) Two T will occur.
(B) One H and one T will occur.
(C) Two H will occur.
(D) One H will be followed by one T.
END OF THE QUESTION PAPER
GATE 2018 Aerospace Engineering
AE 1/9
Q. 1 ? Q. 25 carry one mark each.
Q.1
Let ?? ? , ?? ? ?
be two distinct vectors that are not parallel. The vector ?? ? = ?? ? ? ?? ? ?
is
(A) zero. (B) orthogonal to ?? ? alone.
(C) orthogonal to ?? ? + ?? ? ?
. (D) orthogonal to ?? ? ?
alone.
Q.2
Consider the function ?? (?? , ?? ) =
?? 2
2
+
?? 2
3
? 5. All the roots of this function
(A) form a finite set of points.
(B) lie on an elliptical curve.
(C) lie on the surface of a sphere.
(D) lie on a hyperbolic curve.
Q.3
Consider a vector field given by ?? ?? ? + ?? ?? ? + ?? ?? ?
. This vector field is
(A) divergence-free and curl-free.
(B) curl-free but not divergence-free.
(C) divergence-free but not curl-free.
(D) neither divergence-free nor curl-free.
Q.4 A jet aircraft is initially flying steady and level at its maximum endurance condition. For the
aircraft to fly steady and level, but faster at the same altitude, the pilot should
(A) increase thrust alone.
(B) increase thrust and increase angle of attack.
(C) increase thrust and reduce angle of attack.
(D) reduce angle of attack alone.
Q.5 The pilot of a conventional airplane that is flying steady and level at some altitude, deflects
the port side aileron up and the starboard aileron down. The aircraft will then
(A) pitch, nose up.
(B) roll with the starboard wing up.
(C) pitch, nose down.
(D) roll with the port wing up.
Q.6 A NACA 0012 airfoil has a trailing edge flap. The airfoil is operating at an angle of attack
of 5 degrees with un-deflected flap. If the flap is now deflected by 5 degrees downwards, the
?? ?? versus ?? curve
(A) shifts right and slope increases.
(B) shifts left and slope increases.
(C) shifts left and slope stays the same.
(D) shifts right and slope stays the same.
GATE 2018 Aerospace Engineering
AE 2/9
Q.7 An airplane requires a longer ground roll to lift-off on hot summer days because
(A) the thrust is directly proportional to free-stream density.
(B) the thrust is directly proportional to weight of the aircraft.
(C) the lift-off distance is directly proportional to free-stream density.
(D) the runway friction is high on hot summer days.
Q.8 The velocity profile in an incompressible, laminar boundary layer is shown in the figure
below. U is the free-stream velocity, u(y) is the stream-wise velocity component. The area
of the black shaded region in the figure below represents the
y
(A) boundary layer thickness.
(B) momentum thickness.
(C) displacement thickness.
(D) shape factor.
Q.9 The tangential velocity component ?V? of a spacecraft, which is in a circular orbit of radius
?R? around a spherical Earth (? = GM ? gravitational parameter of Earth) is given by the
following expression.
(A) ?? = ?
?
2?? (B) ?? = ?
?
??
(C) ?? =
2?? ??
?? 3
2
(D) ?? =
2?? ??
?? 2
3
Q.10 Equation of the trajectory of a typical space object around any planet, in polar coordinates
(r, ?) (i.e. a general conic section geometry), is given as follows. (h is angular momentum,
? is gravitational parameter, e is eccentricity, r is radial distance from the planet center, ?,
is angle between vectors ?? ? and ?? ?.
(A) ?? =
(
?
2
?
? )
1??? ?????? ?
(B) ?? =
(
?
2
?
? )
?? ??????? ?
(C) ?? =
(
?
2
?
? )
1+?? ?????? ?
(D) ?? =
(
?
2
?
? )
?? +?????? ?
Q.11 In an elliptic orbit around any planet, the location at which a spacecraft has the maximum
angular velocity is
(A) apoapsis. (B) periapsis.
(C) a point at +45
o
from periapsis. (D) a point at ?90
o
from apoapsis.
u(y)/U
FirstRanker.com - FirstRanker's Choice
GATE 2018 General Aptitude (GA) Set-2
GA 1/3
Q. 1 ? Q. 5 carry one mark each.
Q.1 ?The dress _________ her so well that they all immediately _________ her on her
appearance.?
The words that best fill the blanks in the above sentence are
(A) complemented, complemented (B) complimented, complemented
(C) complimented, complimented (D) complemented, complimented
Q.2 ?The judge?s standing in the legal community, though shaken by false allegations of
wrongdoing, remained _________.?
The word that best fills the blank in the above sentence is
(A) undiminished (B) damaged (C) illegal (D) uncertain
Q.3 Find the missing group of letters in the following series:
BC, FGH, LMNO, _____
(A) UVWXY (B) TUVWX (C) STUVW (D) RSTUV
Q.4 The perimeters of a circle, a square and an equilateral triangle are equal. Which one of the
following statements is true?
(A) The circle has the largest area.
(B) The square has the largest area.
(C) The equilateral triangle has the largest area.
(D) All the three shapes have the same area.
Q.5
The value of the expression
1
1 + log
?? ????
+
1
1 + log
?? ????
+
1
1 + log
?? ????
is _________.
(A) -1 (B) 0 (C) 1 (D) 3
Q. 6 ? Q. 10 carry two marks each.
Q.6 Forty students watched films A, B and C over a week. Each student watched either only
one film or all three. Thirteen students watched film A, sixteen students watched film B
and nineteen students watched film C. How many students watched all three films?
(A) 0 (B) 2 (C) 4 (D) 8
GATE 2018 General Aptitude (GA) Set-2
GA 2/3
Q.7 A wire would enclose an area of 1936 m
2
, if it is bent into a square. The wire is cut into
two pieces. The longer piece is thrice as long as the shorter piece. The long and the short
pieces are bent into a square and a circle, respectively. Which of the following choices is
closest to the sum of the areas enclosed by the two pieces in square meters?
(A) 1096 (B) 1111 (C) 1243 (D) 2486
Q.8 A contract is to be completed in 52 days and 125 identical robots were employed, each
operational for 7 hours a day. After 39 days, five-seventh of the work was completed. How
many additional robots would be required to complete the work on time, if each robot is
now operational for 8 hours a day?
(A) 50 (B) 89 (C) 146 (D) 175
Q.9 A house has a number which needs to be identified. The following three statements are
given that can help in identifying the house number.
i. If the house number is a multiple of 3, then it is a number from 50 to 59.
ii. If the house number is NOT a multiple of 4, then it is a number from 60 to 69.
iii. If the house number is NOT a multiple of 6, then it is a number from 70 to 79.
What is the house number?
(A) 54 (B) 65 (C) 66 (D) 76
GATE 2018 General Aptitude (GA) Set-2
GA 3/3
Q.10 An unbiased coin is tossed six times in a row and four different such trials are conducted.
One trial implies six tosses of the coin. If H stands for head and T stands for tail, the
following are the observations from the four trials:
(1) HTHTHT (2) TTHHHT (3) HTTHHT (4) HHHT__ __.
Which statement describing the last two coin tosses of the fourth trial has the highest
probability of being correct?
(A) Two T will occur.
(B) One H and one T will occur.
(C) Two H will occur.
(D) One H will be followed by one T.
END OF THE QUESTION PAPER
GATE 2018 Aerospace Engineering
AE 1/9
Q. 1 ? Q. 25 carry one mark each.
Q.1
Let ?? ? , ?? ? ?
be two distinct vectors that are not parallel. The vector ?? ? = ?? ? ? ?? ? ?
is
(A) zero. (B) orthogonal to ?? ? alone.
(C) orthogonal to ?? ? + ?? ? ?
. (D) orthogonal to ?? ? ?
alone.
Q.2
Consider the function ?? (?? , ?? ) =
?? 2
2
+
?? 2
3
? 5. All the roots of this function
(A) form a finite set of points.
(B) lie on an elliptical curve.
(C) lie on the surface of a sphere.
(D) lie on a hyperbolic curve.
Q.3
Consider a vector field given by ?? ?? ? + ?? ?? ? + ?? ?? ?
. This vector field is
(A) divergence-free and curl-free.
(B) curl-free but not divergence-free.
(C) divergence-free but not curl-free.
(D) neither divergence-free nor curl-free.
Q.4 A jet aircraft is initially flying steady and level at its maximum endurance condition. For the
aircraft to fly steady and level, but faster at the same altitude, the pilot should
(A) increase thrust alone.
(B) increase thrust and increase angle of attack.
(C) increase thrust and reduce angle of attack.
(D) reduce angle of attack alone.
Q.5 The pilot of a conventional airplane that is flying steady and level at some altitude, deflects
the port side aileron up and the starboard aileron down. The aircraft will then
(A) pitch, nose up.
(B) roll with the starboard wing up.
(C) pitch, nose down.
(D) roll with the port wing up.
Q.6 A NACA 0012 airfoil has a trailing edge flap. The airfoil is operating at an angle of attack
of 5 degrees with un-deflected flap. If the flap is now deflected by 5 degrees downwards, the
?? ?? versus ?? curve
(A) shifts right and slope increases.
(B) shifts left and slope increases.
(C) shifts left and slope stays the same.
(D) shifts right and slope stays the same.
GATE 2018 Aerospace Engineering
AE 2/9
Q.7 An airplane requires a longer ground roll to lift-off on hot summer days because
(A) the thrust is directly proportional to free-stream density.
(B) the thrust is directly proportional to weight of the aircraft.
(C) the lift-off distance is directly proportional to free-stream density.
(D) the runway friction is high on hot summer days.
Q.8 The velocity profile in an incompressible, laminar boundary layer is shown in the figure
below. U is the free-stream velocity, u(y) is the stream-wise velocity component. The area
of the black shaded region in the figure below represents the
y
(A) boundary layer thickness.
(B) momentum thickness.
(C) displacement thickness.
(D) shape factor.
Q.9 The tangential velocity component ?V? of a spacecraft, which is in a circular orbit of radius
?R? around a spherical Earth (? = GM ? gravitational parameter of Earth) is given by the
following expression.
(A) ?? = ?
?
2?? (B) ?? = ?
?
??
(C) ?? =
2?? ??
?? 3
2
(D) ?? =
2?? ??
?? 2
3
Q.10 Equation of the trajectory of a typical space object around any planet, in polar coordinates
(r, ?) (i.e. a general conic section geometry), is given as follows. (h is angular momentum,
? is gravitational parameter, e is eccentricity, r is radial distance from the planet center, ?,
is angle between vectors ?? ? and ?? ?.
(A) ?? =
(
?
2
?
? )
1??? ?????? ?
(B) ?? =
(
?
2
?
? )
?? ??????? ?
(C) ?? =
(
?
2
?
? )
1+?? ?????? ?
(D) ?? =
(
?
2
?
? )
?? +?????? ?
Q.11 In an elliptic orbit around any planet, the location at which a spacecraft has the maximum
angular velocity is
(A) apoapsis. (B) periapsis.
(C) a point at +45
o
from periapsis. (D) a point at ?90
o
from apoapsis.
u(y)/U
GATE 2018 Aerospace Engineering
AE 3/9
Q.12 The pitching moment of a positively cambered NACA airfoil about its leading edge at zero-
lift angle of attack is
(A) negative.
(B) positive.
(C) indeterminate.
(D) zero.
Q.13 In a low-speed wind tunnel, the angular location(s) from the front stagnation point on a
circular cylinder where the static pressure equals the free-stream static pressure, is
(A) ? 38
0
(B) ? 30
0
(C) ? 60
0
(D) 0
0
Q.14 A thermocouple, mounted flush in an insulated flat surface in a supersonic laminar flow of
air measures the
(A) static temperature.
(B) temperature greater than static but less than total temperature.
(C) total temperature.
(D) temperature greater than total temperature.
Q.15 A shock wave is moving into still air in a shock tube. Which one of the following happens
to the air?
(A) static temperature increases, total temperature remains constant.
(B) static temperature increases, total temperature increases.
(C) static temperature increases, total temperature decreases.
(D) static pressure increases, total temperature remains constant.
Q.16 The highest limit load factor experienced by a civil transport aircraft is in the range
(A) 0.0 ? 2.0 (B) 2.0 ? 5.0 (C) 5.0 ? 8.0 (D) 8.0 ? 10.0
Q.17 Determine the correctness or otherwise of the following statements, [a] and [r]:
[a] A closed-section box beam configuration is used in aircraft wings.
[r] Closed-section box beam configuration is capable of resisting torsional loads.
(A) Both [a] and [r] are true and [r] is the correct reason for [a].
(B) Both [a] and [r] are true but [r] is not the correct reason for [a].
(C) Both [a] and [r] are false.
(D) [a] is true but [r] is false.
FirstRanker.com - FirstRanker's Choice
GATE 2018 General Aptitude (GA) Set-2
GA 1/3
Q. 1 ? Q. 5 carry one mark each.
Q.1 ?The dress _________ her so well that they all immediately _________ her on her
appearance.?
The words that best fill the blanks in the above sentence are
(A) complemented, complemented (B) complimented, complemented
(C) complimented, complimented (D) complemented, complimented
Q.2 ?The judge?s standing in the legal community, though shaken by false allegations of
wrongdoing, remained _________.?
The word that best fills the blank in the above sentence is
(A) undiminished (B) damaged (C) illegal (D) uncertain
Q.3 Find the missing group of letters in the following series:
BC, FGH, LMNO, _____
(A) UVWXY (B) TUVWX (C) STUVW (D) RSTUV
Q.4 The perimeters of a circle, a square and an equilateral triangle are equal. Which one of the
following statements is true?
(A) The circle has the largest area.
(B) The square has the largest area.
(C) The equilateral triangle has the largest area.
(D) All the three shapes have the same area.
Q.5
The value of the expression
1
1 + log
?? ????
+
1
1 + log
?? ????
+
1
1 + log
?? ????
is _________.
(A) -1 (B) 0 (C) 1 (D) 3
Q. 6 ? Q. 10 carry two marks each.
Q.6 Forty students watched films A, B and C over a week. Each student watched either only
one film or all three. Thirteen students watched film A, sixteen students watched film B
and nineteen students watched film C. How many students watched all three films?
(A) 0 (B) 2 (C) 4 (D) 8
GATE 2018 General Aptitude (GA) Set-2
GA 2/3
Q.7 A wire would enclose an area of 1936 m
2
, if it is bent into a square. The wire is cut into
two pieces. The longer piece is thrice as long as the shorter piece. The long and the short
pieces are bent into a square and a circle, respectively. Which of the following choices is
closest to the sum of the areas enclosed by the two pieces in square meters?
(A) 1096 (B) 1111 (C) 1243 (D) 2486
Q.8 A contract is to be completed in 52 days and 125 identical robots were employed, each
operational for 7 hours a day. After 39 days, five-seventh of the work was completed. How
many additional robots would be required to complete the work on time, if each robot is
now operational for 8 hours a day?
(A) 50 (B) 89 (C) 146 (D) 175
Q.9 A house has a number which needs to be identified. The following three statements are
given that can help in identifying the house number.
i. If the house number is a multiple of 3, then it is a number from 50 to 59.
ii. If the house number is NOT a multiple of 4, then it is a number from 60 to 69.
iii. If the house number is NOT a multiple of 6, then it is a number from 70 to 79.
What is the house number?
(A) 54 (B) 65 (C) 66 (D) 76
GATE 2018 General Aptitude (GA) Set-2
GA 3/3
Q.10 An unbiased coin is tossed six times in a row and four different such trials are conducted.
One trial implies six tosses of the coin. If H stands for head and T stands for tail, the
following are the observations from the four trials:
(1) HTHTHT (2) TTHHHT (3) HTTHHT (4) HHHT__ __.
Which statement describing the last two coin tosses of the fourth trial has the highest
probability of being correct?
(A) Two T will occur.
(B) One H and one T will occur.
(C) Two H will occur.
(D) One H will be followed by one T.
END OF THE QUESTION PAPER
GATE 2018 Aerospace Engineering
AE 1/9
Q. 1 ? Q. 25 carry one mark each.
Q.1
Let ?? ? , ?? ? ?
be two distinct vectors that are not parallel. The vector ?? ? = ?? ? ? ?? ? ?
is
(A) zero. (B) orthogonal to ?? ? alone.
(C) orthogonal to ?? ? + ?? ? ?
. (D) orthogonal to ?? ? ?
alone.
Q.2
Consider the function ?? (?? , ?? ) =
?? 2
2
+
?? 2
3
? 5. All the roots of this function
(A) form a finite set of points.
(B) lie on an elliptical curve.
(C) lie on the surface of a sphere.
(D) lie on a hyperbolic curve.
Q.3
Consider a vector field given by ?? ?? ? + ?? ?? ? + ?? ?? ?
. This vector field is
(A) divergence-free and curl-free.
(B) curl-free but not divergence-free.
(C) divergence-free but not curl-free.
(D) neither divergence-free nor curl-free.
Q.4 A jet aircraft is initially flying steady and level at its maximum endurance condition. For the
aircraft to fly steady and level, but faster at the same altitude, the pilot should
(A) increase thrust alone.
(B) increase thrust and increase angle of attack.
(C) increase thrust and reduce angle of attack.
(D) reduce angle of attack alone.
Q.5 The pilot of a conventional airplane that is flying steady and level at some altitude, deflects
the port side aileron up and the starboard aileron down. The aircraft will then
(A) pitch, nose up.
(B) roll with the starboard wing up.
(C) pitch, nose down.
(D) roll with the port wing up.
Q.6 A NACA 0012 airfoil has a trailing edge flap. The airfoil is operating at an angle of attack
of 5 degrees with un-deflected flap. If the flap is now deflected by 5 degrees downwards, the
?? ?? versus ?? curve
(A) shifts right and slope increases.
(B) shifts left and slope increases.
(C) shifts left and slope stays the same.
(D) shifts right and slope stays the same.
GATE 2018 Aerospace Engineering
AE 2/9
Q.7 An airplane requires a longer ground roll to lift-off on hot summer days because
(A) the thrust is directly proportional to free-stream density.
(B) the thrust is directly proportional to weight of the aircraft.
(C) the lift-off distance is directly proportional to free-stream density.
(D) the runway friction is high on hot summer days.
Q.8 The velocity profile in an incompressible, laminar boundary layer is shown in the figure
below. U is the free-stream velocity, u(y) is the stream-wise velocity component. The area
of the black shaded region in the figure below represents the
y
(A) boundary layer thickness.
(B) momentum thickness.
(C) displacement thickness.
(D) shape factor.
Q.9 The tangential velocity component ?V? of a spacecraft, which is in a circular orbit of radius
?R? around a spherical Earth (? = GM ? gravitational parameter of Earth) is given by the
following expression.
(A) ?? = ?
?
2?? (B) ?? = ?
?
??
(C) ?? =
2?? ??
?? 3
2
(D) ?? =
2?? ??
?? 2
3
Q.10 Equation of the trajectory of a typical space object around any planet, in polar coordinates
(r, ?) (i.e. a general conic section geometry), is given as follows. (h is angular momentum,
? is gravitational parameter, e is eccentricity, r is radial distance from the planet center, ?,
is angle between vectors ?? ? and ?? ?.
(A) ?? =
(
?
2
?
? )
1??? ?????? ?
(B) ?? =
(
?
2
?
? )
?? ??????? ?
(C) ?? =
(
?
2
?
? )
1+?? ?????? ?
(D) ?? =
(
?
2
?
? )
?? +?????? ?
Q.11 In an elliptic orbit around any planet, the location at which a spacecraft has the maximum
angular velocity is
(A) apoapsis. (B) periapsis.
(C) a point at +45
o
from periapsis. (D) a point at ?90
o
from apoapsis.
u(y)/U
GATE 2018 Aerospace Engineering
AE 3/9
Q.12 The pitching moment of a positively cambered NACA airfoil about its leading edge at zero-
lift angle of attack is
(A) negative.
(B) positive.
(C) indeterminate.
(D) zero.
Q.13 In a low-speed wind tunnel, the angular location(s) from the front stagnation point on a
circular cylinder where the static pressure equals the free-stream static pressure, is
(A) ? 38
0
(B) ? 30
0
(C) ? 60
0
(D) 0
0
Q.14 A thermocouple, mounted flush in an insulated flat surface in a supersonic laminar flow of
air measures the
(A) static temperature.
(B) temperature greater than static but less than total temperature.
(C) total temperature.
(D) temperature greater than total temperature.
Q.15 A shock wave is moving into still air in a shock tube. Which one of the following happens
to the air?
(A) static temperature increases, total temperature remains constant.
(B) static temperature increases, total temperature increases.
(C) static temperature increases, total temperature decreases.
(D) static pressure increases, total temperature remains constant.
Q.16 The highest limit load factor experienced by a civil transport aircraft is in the range
(A) 0.0 ? 2.0 (B) 2.0 ? 5.0 (C) 5.0 ? 8.0 (D) 8.0 ? 10.0
Q.17 Determine the correctness or otherwise of the following statements, [a] and [r]:
[a] A closed-section box beam configuration is used in aircraft wings.
[r] Closed-section box beam configuration is capable of resisting torsional loads.
(A) Both [a] and [r] are true and [r] is the correct reason for [a].
(B) Both [a] and [r] are true but [r] is not the correct reason for [a].
(C) Both [a] and [r] are false.
(D) [a] is true but [r] is false.
GATE 2018 Aerospace Engineering
AE 4/9
Q.18 The first law of thermodynamics is also known as conservation of
(A) mass.
(B) momentum.
(C) energy.
(D) species.
Q.19 In an ideal gas turbine cycle, the expansion in a turbine is represented by
(A) an isenthalpic process. (B) an isentropic process.
(C) an isobaric process. (D) an isochoric process.
Q.20
The determinant of the matrix [
1 1 ?1
2 1 0
3 1 1
] is ______ (accurate to one decimal place).
Q.21 The theoretical maximum velocity (in m/s) of air expanding from a reservoir at 700 K is
__________ (accurate to two decimal places). Specific heat of air at constant pressure is
1005 J/(kg-K).
Q.22 For a damped single degree of freedom system with damping ratio of 0.1, ratio of two
successive peak amplitudes of free vibration is ___________ (accurate to two decimal
places).
Q.23 The natural frequency (in rad/s) of the spring-mass system shown in the figure below is
_____ (accurate to one decimal place).
Q.24 The stagnation pressures at the inlet and exit of a subsonic intake are 100 kPa and 98 kPa,
respectively. The pressure recovery of this intake will be ______ (accurate to two decimal
places).
Q.25 A combustor is operating with a fuel-air ratio of 0.03. If the stoichiometric fuel-air ratio of
the fuel used is 0.06, the equivalence ratio of the combustor will be _______ (accurate to
two decimal places).
FirstRanker.com - FirstRanker's Choice
GATE 2018 General Aptitude (GA) Set-2
GA 1/3
Q. 1 ? Q. 5 carry one mark each.
Q.1 ?The dress _________ her so well that they all immediately _________ her on her
appearance.?
The words that best fill the blanks in the above sentence are
(A) complemented, complemented (B) complimented, complemented
(C) complimented, complimented (D) complemented, complimented
Q.2 ?The judge?s standing in the legal community, though shaken by false allegations of
wrongdoing, remained _________.?
The word that best fills the blank in the above sentence is
(A) undiminished (B) damaged (C) illegal (D) uncertain
Q.3 Find the missing group of letters in the following series:
BC, FGH, LMNO, _____
(A) UVWXY (B) TUVWX (C) STUVW (D) RSTUV
Q.4 The perimeters of a circle, a square and an equilateral triangle are equal. Which one of the
following statements is true?
(A) The circle has the largest area.
(B) The square has the largest area.
(C) The equilateral triangle has the largest area.
(D) All the three shapes have the same area.
Q.5
The value of the expression
1
1 + log
?? ????
+
1
1 + log
?? ????
+
1
1 + log
?? ????
is _________.
(A) -1 (B) 0 (C) 1 (D) 3
Q. 6 ? Q. 10 carry two marks each.
Q.6 Forty students watched films A, B and C over a week. Each student watched either only
one film or all three. Thirteen students watched film A, sixteen students watched film B
and nineteen students watched film C. How many students watched all three films?
(A) 0 (B) 2 (C) 4 (D) 8
GATE 2018 General Aptitude (GA) Set-2
GA 2/3
Q.7 A wire would enclose an area of 1936 m
2
, if it is bent into a square. The wire is cut into
two pieces. The longer piece is thrice as long as the shorter piece. The long and the short
pieces are bent into a square and a circle, respectively. Which of the following choices is
closest to the sum of the areas enclosed by the two pieces in square meters?
(A) 1096 (B) 1111 (C) 1243 (D) 2486
Q.8 A contract is to be completed in 52 days and 125 identical robots were employed, each
operational for 7 hours a day. After 39 days, five-seventh of the work was completed. How
many additional robots would be required to complete the work on time, if each robot is
now operational for 8 hours a day?
(A) 50 (B) 89 (C) 146 (D) 175
Q.9 A house has a number which needs to be identified. The following three statements are
given that can help in identifying the house number.
i. If the house number is a multiple of 3, then it is a number from 50 to 59.
ii. If the house number is NOT a multiple of 4, then it is a number from 60 to 69.
iii. If the house number is NOT a multiple of 6, then it is a number from 70 to 79.
What is the house number?
(A) 54 (B) 65 (C) 66 (D) 76
GATE 2018 General Aptitude (GA) Set-2
GA 3/3
Q.10 An unbiased coin is tossed six times in a row and four different such trials are conducted.
One trial implies six tosses of the coin. If H stands for head and T stands for tail, the
following are the observations from the four trials:
(1) HTHTHT (2) TTHHHT (3) HTTHHT (4) HHHT__ __.
Which statement describing the last two coin tosses of the fourth trial has the highest
probability of being correct?
(A) Two T will occur.
(B) One H and one T will occur.
(C) Two H will occur.
(D) One H will be followed by one T.
END OF THE QUESTION PAPER
GATE 2018 Aerospace Engineering
AE 1/9
Q. 1 ? Q. 25 carry one mark each.
Q.1
Let ?? ? , ?? ? ?
be two distinct vectors that are not parallel. The vector ?? ? = ?? ? ? ?? ? ?
is
(A) zero. (B) orthogonal to ?? ? alone.
(C) orthogonal to ?? ? + ?? ? ?
. (D) orthogonal to ?? ? ?
alone.
Q.2
Consider the function ?? (?? , ?? ) =
?? 2
2
+
?? 2
3
? 5. All the roots of this function
(A) form a finite set of points.
(B) lie on an elliptical curve.
(C) lie on the surface of a sphere.
(D) lie on a hyperbolic curve.
Q.3
Consider a vector field given by ?? ?? ? + ?? ?? ? + ?? ?? ?
. This vector field is
(A) divergence-free and curl-free.
(B) curl-free but not divergence-free.
(C) divergence-free but not curl-free.
(D) neither divergence-free nor curl-free.
Q.4 A jet aircraft is initially flying steady and level at its maximum endurance condition. For the
aircraft to fly steady and level, but faster at the same altitude, the pilot should
(A) increase thrust alone.
(B) increase thrust and increase angle of attack.
(C) increase thrust and reduce angle of attack.
(D) reduce angle of attack alone.
Q.5 The pilot of a conventional airplane that is flying steady and level at some altitude, deflects
the port side aileron up and the starboard aileron down. The aircraft will then
(A) pitch, nose up.
(B) roll with the starboard wing up.
(C) pitch, nose down.
(D) roll with the port wing up.
Q.6 A NACA 0012 airfoil has a trailing edge flap. The airfoil is operating at an angle of attack
of 5 degrees with un-deflected flap. If the flap is now deflected by 5 degrees downwards, the
?? ?? versus ?? curve
(A) shifts right and slope increases.
(B) shifts left and slope increases.
(C) shifts left and slope stays the same.
(D) shifts right and slope stays the same.
GATE 2018 Aerospace Engineering
AE 2/9
Q.7 An airplane requires a longer ground roll to lift-off on hot summer days because
(A) the thrust is directly proportional to free-stream density.
(B) the thrust is directly proportional to weight of the aircraft.
(C) the lift-off distance is directly proportional to free-stream density.
(D) the runway friction is high on hot summer days.
Q.8 The velocity profile in an incompressible, laminar boundary layer is shown in the figure
below. U is the free-stream velocity, u(y) is the stream-wise velocity component. The area
of the black shaded region in the figure below represents the
y
(A) boundary layer thickness.
(B) momentum thickness.
(C) displacement thickness.
(D) shape factor.
Q.9 The tangential velocity component ?V? of a spacecraft, which is in a circular orbit of radius
?R? around a spherical Earth (? = GM ? gravitational parameter of Earth) is given by the
following expression.
(A) ?? = ?
?
2?? (B) ?? = ?
?
??
(C) ?? =
2?? ??
?? 3
2
(D) ?? =
2?? ??
?? 2
3
Q.10 Equation of the trajectory of a typical space object around any planet, in polar coordinates
(r, ?) (i.e. a general conic section geometry), is given as follows. (h is angular momentum,
? is gravitational parameter, e is eccentricity, r is radial distance from the planet center, ?,
is angle between vectors ?? ? and ?? ?.
(A) ?? =
(
?
2
?
? )
1??? ?????? ?
(B) ?? =
(
?
2
?
? )
?? ??????? ?
(C) ?? =
(
?
2
?
? )
1+?? ?????? ?
(D) ?? =
(
?
2
?
? )
?? +?????? ?
Q.11 In an elliptic orbit around any planet, the location at which a spacecraft has the maximum
angular velocity is
(A) apoapsis. (B) periapsis.
(C) a point at +45
o
from periapsis. (D) a point at ?90
o
from apoapsis.
u(y)/U
GATE 2018 Aerospace Engineering
AE 3/9
Q.12 The pitching moment of a positively cambered NACA airfoil about its leading edge at zero-
lift angle of attack is
(A) negative.
(B) positive.
(C) indeterminate.
(D) zero.
Q.13 In a low-speed wind tunnel, the angular location(s) from the front stagnation point on a
circular cylinder where the static pressure equals the free-stream static pressure, is
(A) ? 38
0
(B) ? 30
0
(C) ? 60
0
(D) 0
0
Q.14 A thermocouple, mounted flush in an insulated flat surface in a supersonic laminar flow of
air measures the
(A) static temperature.
(B) temperature greater than static but less than total temperature.
(C) total temperature.
(D) temperature greater than total temperature.
Q.15 A shock wave is moving into still air in a shock tube. Which one of the following happens
to the air?
(A) static temperature increases, total temperature remains constant.
(B) static temperature increases, total temperature increases.
(C) static temperature increases, total temperature decreases.
(D) static pressure increases, total temperature remains constant.
Q.16 The highest limit load factor experienced by a civil transport aircraft is in the range
(A) 0.0 ? 2.0 (B) 2.0 ? 5.0 (C) 5.0 ? 8.0 (D) 8.0 ? 10.0
Q.17 Determine the correctness or otherwise of the following statements, [a] and [r]:
[a] A closed-section box beam configuration is used in aircraft wings.
[r] Closed-section box beam configuration is capable of resisting torsional loads.
(A) Both [a] and [r] are true and [r] is the correct reason for [a].
(B) Both [a] and [r] are true but [r] is not the correct reason for [a].
(C) Both [a] and [r] are false.
(D) [a] is true but [r] is false.
GATE 2018 Aerospace Engineering
AE 4/9
Q.18 The first law of thermodynamics is also known as conservation of
(A) mass.
(B) momentum.
(C) energy.
(D) species.
Q.19 In an ideal gas turbine cycle, the expansion in a turbine is represented by
(A) an isenthalpic process. (B) an isentropic process.
(C) an isobaric process. (D) an isochoric process.
Q.20
The determinant of the matrix [
1 1 ?1
2 1 0
3 1 1
] is ______ (accurate to one decimal place).
Q.21 The theoretical maximum velocity (in m/s) of air expanding from a reservoir at 700 K is
__________ (accurate to two decimal places). Specific heat of air at constant pressure is
1005 J/(kg-K).
Q.22 For a damped single degree of freedom system with damping ratio of 0.1, ratio of two
successive peak amplitudes of free vibration is ___________ (accurate to two decimal
places).
Q.23 The natural frequency (in rad/s) of the spring-mass system shown in the figure below is
_____ (accurate to one decimal place).
Q.24 The stagnation pressures at the inlet and exit of a subsonic intake are 100 kPa and 98 kPa,
respectively. The pressure recovery of this intake will be ______ (accurate to two decimal
places).
Q.25 A combustor is operating with a fuel-air ratio of 0.03. If the stoichiometric fuel-air ratio of
the fuel used is 0.06, the equivalence ratio of the combustor will be _______ (accurate to
two decimal places).
GATE 2018 Aerospace Engineering
AE 5/9
Q. 26 ? Q. 55 carry two marks each.
Q.26
The solution of the differential equation
?? 2
?? ?? ?? 2
+ 3
????
????
= 0, given that ?? = 0 and
????
????
= 1 at
?? = 0 is
(A) ?? (1 ? ?? ?3?? )
(B)
1
3
(1 ? ?? ?3?? ) (C)
1
3
(1 + ?? ?3?? )
(D)
1
3
????
?3?? 2
Q.27 The relation between pressure (p) and velocity (V) for a steady, isentropic flow at two points
along a streamline is, (c is a constant)
(A) ?? (?? 2
?? ? ?? 1
?? ) =
?? 1
2
2
?
?? 2
2
2
(B) ?? (?? 2
?? ?? ?1
? ?? 1
?? ?? ?1
) =
?? 1
2
2
?
?? 2
2
2
(C) ?? (?? 2
?? ?1
?? ? ?? 1
?? ?1
?? ) =
?? 1
2
2
?
?? 2
2
2
(D) ?? (?? 2
?? ?1
? ?? 1
?? ?1
) =
?? 1
2
2
?
?? 2
2
2
Q.28 A thin airfoil is mounted in a low-speed, subsonic wind tunnel, in which the Mach number
is 0.1. At a point on the airfoil, the pressure coefficient is measured to be ?1.2. If the flow
velocity is increased such that the free-stream Mach number is 0.6, the pressure coefficient
at the same point on the airfoil will approximately be:
(A) ?3.5 (B) ?2.9 (C) ?1.5 (D) ?0.75
Q.29 A solid circular shaft of diameter d is under pure torsion of magnitude T. The maximum
tensile stress experienced at any point on the shaft is
(A)
32?? ?? ?? 3
(B)
16?? ?? ?? 4
(C)
32?? ?? ?? 4
(D)
16?? ?? ?? 3
Q.30 A clamped-clamped beam, subjected to a point load P at the midspan, is shown in the figure
below. The magnitude of the moment reaction at the two fixed ends of the beam is
(A) PL/2 (B) PL/4 (C) PL/8 (D) PL/16
FirstRanker.com - FirstRanker's Choice
GATE 2018 General Aptitude (GA) Set-2
GA 1/3
Q. 1 ? Q. 5 carry one mark each.
Q.1 ?The dress _________ her so well that they all immediately _________ her on her
appearance.?
The words that best fill the blanks in the above sentence are
(A) complemented, complemented (B) complimented, complemented
(C) complimented, complimented (D) complemented, complimented
Q.2 ?The judge?s standing in the legal community, though shaken by false allegations of
wrongdoing, remained _________.?
The word that best fills the blank in the above sentence is
(A) undiminished (B) damaged (C) illegal (D) uncertain
Q.3 Find the missing group of letters in the following series:
BC, FGH, LMNO, _____
(A) UVWXY (B) TUVWX (C) STUVW (D) RSTUV
Q.4 The perimeters of a circle, a square and an equilateral triangle are equal. Which one of the
following statements is true?
(A) The circle has the largest area.
(B) The square has the largest area.
(C) The equilateral triangle has the largest area.
(D) All the three shapes have the same area.
Q.5
The value of the expression
1
1 + log
?? ????
+
1
1 + log
?? ????
+
1
1 + log
?? ????
is _________.
(A) -1 (B) 0 (C) 1 (D) 3
Q. 6 ? Q. 10 carry two marks each.
Q.6 Forty students watched films A, B and C over a week. Each student watched either only
one film or all three. Thirteen students watched film A, sixteen students watched film B
and nineteen students watched film C. How many students watched all three films?
(A) 0 (B) 2 (C) 4 (D) 8
GATE 2018 General Aptitude (GA) Set-2
GA 2/3
Q.7 A wire would enclose an area of 1936 m
2
, if it is bent into a square. The wire is cut into
two pieces. The longer piece is thrice as long as the shorter piece. The long and the short
pieces are bent into a square and a circle, respectively. Which of the following choices is
closest to the sum of the areas enclosed by the two pieces in square meters?
(A) 1096 (B) 1111 (C) 1243 (D) 2486
Q.8 A contract is to be completed in 52 days and 125 identical robots were employed, each
operational for 7 hours a day. After 39 days, five-seventh of the work was completed. How
many additional robots would be required to complete the work on time, if each robot is
now operational for 8 hours a day?
(A) 50 (B) 89 (C) 146 (D) 175
Q.9 A house has a number which needs to be identified. The following three statements are
given that can help in identifying the house number.
i. If the house number is a multiple of 3, then it is a number from 50 to 59.
ii. If the house number is NOT a multiple of 4, then it is a number from 60 to 69.
iii. If the house number is NOT a multiple of 6, then it is a number from 70 to 79.
What is the house number?
(A) 54 (B) 65 (C) 66 (D) 76
GATE 2018 General Aptitude (GA) Set-2
GA 3/3
Q.10 An unbiased coin is tossed six times in a row and four different such trials are conducted.
One trial implies six tosses of the coin. If H stands for head and T stands for tail, the
following are the observations from the four trials:
(1) HTHTHT (2) TTHHHT (3) HTTHHT (4) HHHT__ __.
Which statement describing the last two coin tosses of the fourth trial has the highest
probability of being correct?
(A) Two T will occur.
(B) One H and one T will occur.
(C) Two H will occur.
(D) One H will be followed by one T.
END OF THE QUESTION PAPER
GATE 2018 Aerospace Engineering
AE 1/9
Q. 1 ? Q. 25 carry one mark each.
Q.1
Let ?? ? , ?? ? ?
be two distinct vectors that are not parallel. The vector ?? ? = ?? ? ? ?? ? ?
is
(A) zero. (B) orthogonal to ?? ? alone.
(C) orthogonal to ?? ? + ?? ? ?
. (D) orthogonal to ?? ? ?
alone.
Q.2
Consider the function ?? (?? , ?? ) =
?? 2
2
+
?? 2
3
? 5. All the roots of this function
(A) form a finite set of points.
(B) lie on an elliptical curve.
(C) lie on the surface of a sphere.
(D) lie on a hyperbolic curve.
Q.3
Consider a vector field given by ?? ?? ? + ?? ?? ? + ?? ?? ?
. This vector field is
(A) divergence-free and curl-free.
(B) curl-free but not divergence-free.
(C) divergence-free but not curl-free.
(D) neither divergence-free nor curl-free.
Q.4 A jet aircraft is initially flying steady and level at its maximum endurance condition. For the
aircraft to fly steady and level, but faster at the same altitude, the pilot should
(A) increase thrust alone.
(B) increase thrust and increase angle of attack.
(C) increase thrust and reduce angle of attack.
(D) reduce angle of attack alone.
Q.5 The pilot of a conventional airplane that is flying steady and level at some altitude, deflects
the port side aileron up and the starboard aileron down. The aircraft will then
(A) pitch, nose up.
(B) roll with the starboard wing up.
(C) pitch, nose down.
(D) roll with the port wing up.
Q.6 A NACA 0012 airfoil has a trailing edge flap. The airfoil is operating at an angle of attack
of 5 degrees with un-deflected flap. If the flap is now deflected by 5 degrees downwards, the
?? ?? versus ?? curve
(A) shifts right and slope increases.
(B) shifts left and slope increases.
(C) shifts left and slope stays the same.
(D) shifts right and slope stays the same.
GATE 2018 Aerospace Engineering
AE 2/9
Q.7 An airplane requires a longer ground roll to lift-off on hot summer days because
(A) the thrust is directly proportional to free-stream density.
(B) the thrust is directly proportional to weight of the aircraft.
(C) the lift-off distance is directly proportional to free-stream density.
(D) the runway friction is high on hot summer days.
Q.8 The velocity profile in an incompressible, laminar boundary layer is shown in the figure
below. U is the free-stream velocity, u(y) is the stream-wise velocity component. The area
of the black shaded region in the figure below represents the
y
(A) boundary layer thickness.
(B) momentum thickness.
(C) displacement thickness.
(D) shape factor.
Q.9 The tangential velocity component ?V? of a spacecraft, which is in a circular orbit of radius
?R? around a spherical Earth (? = GM ? gravitational parameter of Earth) is given by the
following expression.
(A) ?? = ?
?
2?? (B) ?? = ?
?
??
(C) ?? =
2?? ??
?? 3
2
(D) ?? =
2?? ??
?? 2
3
Q.10 Equation of the trajectory of a typical space object around any planet, in polar coordinates
(r, ?) (i.e. a general conic section geometry), is given as follows. (h is angular momentum,
? is gravitational parameter, e is eccentricity, r is radial distance from the planet center, ?,
is angle between vectors ?? ? and ?? ?.
(A) ?? =
(
?
2
?
? )
1??? ?????? ?
(B) ?? =
(
?
2
?
? )
?? ??????? ?
(C) ?? =
(
?
2
?
? )
1+?? ?????? ?
(D) ?? =
(
?
2
?
? )
?? +?????? ?
Q.11 In an elliptic orbit around any planet, the location at which a spacecraft has the maximum
angular velocity is
(A) apoapsis. (B) periapsis.
(C) a point at +45
o
from periapsis. (D) a point at ?90
o
from apoapsis.
u(y)/U
GATE 2018 Aerospace Engineering
AE 3/9
Q.12 The pitching moment of a positively cambered NACA airfoil about its leading edge at zero-
lift angle of attack is
(A) negative.
(B) positive.
(C) indeterminate.
(D) zero.
Q.13 In a low-speed wind tunnel, the angular location(s) from the front stagnation point on a
circular cylinder where the static pressure equals the free-stream static pressure, is
(A) ? 38
0
(B) ? 30
0
(C) ? 60
0
(D) 0
0
Q.14 A thermocouple, mounted flush in an insulated flat surface in a supersonic laminar flow of
air measures the
(A) static temperature.
(B) temperature greater than static but less than total temperature.
(C) total temperature.
(D) temperature greater than total temperature.
Q.15 A shock wave is moving into still air in a shock tube. Which one of the following happens
to the air?
(A) static temperature increases, total temperature remains constant.
(B) static temperature increases, total temperature increases.
(C) static temperature increases, total temperature decreases.
(D) static pressure increases, total temperature remains constant.
Q.16 The highest limit load factor experienced by a civil transport aircraft is in the range
(A) 0.0 ? 2.0 (B) 2.0 ? 5.0 (C) 5.0 ? 8.0 (D) 8.0 ? 10.0
Q.17 Determine the correctness or otherwise of the following statements, [a] and [r]:
[a] A closed-section box beam configuration is used in aircraft wings.
[r] Closed-section box beam configuration is capable of resisting torsional loads.
(A) Both [a] and [r] are true and [r] is the correct reason for [a].
(B) Both [a] and [r] are true but [r] is not the correct reason for [a].
(C) Both [a] and [r] are false.
(D) [a] is true but [r] is false.
GATE 2018 Aerospace Engineering
AE 4/9
Q.18 The first law of thermodynamics is also known as conservation of
(A) mass.
(B) momentum.
(C) energy.
(D) species.
Q.19 In an ideal gas turbine cycle, the expansion in a turbine is represented by
(A) an isenthalpic process. (B) an isentropic process.
(C) an isobaric process. (D) an isochoric process.
Q.20
The determinant of the matrix [
1 1 ?1
2 1 0
3 1 1
] is ______ (accurate to one decimal place).
Q.21 The theoretical maximum velocity (in m/s) of air expanding from a reservoir at 700 K is
__________ (accurate to two decimal places). Specific heat of air at constant pressure is
1005 J/(kg-K).
Q.22 For a damped single degree of freedom system with damping ratio of 0.1, ratio of two
successive peak amplitudes of free vibration is ___________ (accurate to two decimal
places).
Q.23 The natural frequency (in rad/s) of the spring-mass system shown in the figure below is
_____ (accurate to one decimal place).
Q.24 The stagnation pressures at the inlet and exit of a subsonic intake are 100 kPa and 98 kPa,
respectively. The pressure recovery of this intake will be ______ (accurate to two decimal
places).
Q.25 A combustor is operating with a fuel-air ratio of 0.03. If the stoichiometric fuel-air ratio of
the fuel used is 0.06, the equivalence ratio of the combustor will be _______ (accurate to
two decimal places).
GATE 2018 Aerospace Engineering
AE 5/9
Q. 26 ? Q. 55 carry two marks each.
Q.26
The solution of the differential equation
?? 2
?? ?? ?? 2
+ 3
????
????
= 0, given that ?? = 0 and
????
????
= 1 at
?? = 0 is
(A) ?? (1 ? ?? ?3?? )
(B)
1
3
(1 ? ?? ?3?? ) (C)
1
3
(1 + ?? ?3?? )
(D)
1
3
????
?3?? 2
Q.27 The relation between pressure (p) and velocity (V) for a steady, isentropic flow at two points
along a streamline is, (c is a constant)
(A) ?? (?? 2
?? ? ?? 1
?? ) =
?? 1
2
2
?
?? 2
2
2
(B) ?? (?? 2
?? ?? ?1
? ?? 1
?? ?? ?1
) =
?? 1
2
2
?
?? 2
2
2
(C) ?? (?? 2
?? ?1
?? ? ?? 1
?? ?1
?? ) =
?? 1
2
2
?
?? 2
2
2
(D) ?? (?? 2
?? ?1
? ?? 1
?? ?1
) =
?? 1
2
2
?
?? 2
2
2
Q.28 A thin airfoil is mounted in a low-speed, subsonic wind tunnel, in which the Mach number
is 0.1. At a point on the airfoil, the pressure coefficient is measured to be ?1.2. If the flow
velocity is increased such that the free-stream Mach number is 0.6, the pressure coefficient
at the same point on the airfoil will approximately be:
(A) ?3.5 (B) ?2.9 (C) ?1.5 (D) ?0.75
Q.29 A solid circular shaft of diameter d is under pure torsion of magnitude T. The maximum
tensile stress experienced at any point on the shaft is
(A)
32?? ?? ?? 3
(B)
16?? ?? ?? 4
(C)
32?? ?? ?? 4
(D)
16?? ?? ?? 3
Q.30 A clamped-clamped beam, subjected to a point load P at the midspan, is shown in the figure
below. The magnitude of the moment reaction at the two fixed ends of the beam is
(A) PL/2 (B) PL/4 (C) PL/8 (D) PL/16
GATE 2018 Aerospace Engineering
AE 6/9
Q.31 Which of the following statement(s) is/are true about the state of a body in plane strain
condition?
P: All the points in the body undergo displacements in one plane only, for example the x-y
plane, leading to ?? ????
= ?? ????
= ?? ????
= 0.
Q: All the components of stress perpendicular to the plane of deformation, for example the
x-y plane, of the body are equal to zero, i.e. ?? ????
= ?? ????
= ?? ????
= 0.
R: Except the normal component, all the other components of stress perpendicular to the
plane of deformation of the body, for example the x-y plane, are equal to zero, i.e. ?? ????
? 0,
?? ????
= ?? ????
= 0.
(A) P only (B) Q only (C) P and Q (D) P and R
Q.32 An aircraft with a turbojet engine flies at a velocity of 100 m/s. If the jet exhaust velocity is
300 m/s, the propulsive efficiency of the engine, assuming a negligible fuel-air ratio, is
(A) 0.33 (B) 0.50 (C) 0.67 (D) 0.80
Q.33 An aircraft with a turboprop engine produces a thrust of 500 N and flies at 100 m/s. If the
propeller efficiency is 0.5, the shaft power produced by the engine is
(A) 50 kW (B) 100 kW
(C) 125 kW (D) 500 kW
Q.34 An axial compressor that generates a stagnation pressure ratio of 4.0, operates with inlet and
exit stagnation temperatures of 300 K and 480 K, respectively. If the ratio of specific heats
(?? ) is 1.4, the isentropic efficiency of the compressor is
(A) 0.94 (B) 0.81
(C) 0.72 (D) 0.63
Q.35 A rocket has an initial mass of 150 kg. After operating for a duration of 10 s, its final mass
is 50 kg. If the acceleration due to gravity is 9.81 m/s
2
and the thrust produced by the rocket
is 19.62 kN, the specific impulse of the rocket is
(A) 400 s (B) 300 s
(C) 200 s (D) 100 s
Q.36
Consider the vector field ?? ? = ?
?? ?? 2
?? ? +
?? ?? 2
?? ? ; where ?? = ??? 2
+ ?? 2
. The contour integral
? ?? ? ? ???? ? ? ? ??
, where ???? ? ? ? ??
is tangent to the contour that encloses the origin, is __________ (accurate
to two decimal places).
Q.37 The magnitude of the x-component of a unit vector at the point (1, 1) that is normal to equi-
potential lines of the potential function ?? (?? ) =
1
?? 2
+4
, where ?? = ??? 2
+ ?? 2
, is _______
(accurate to two decimal places).
FirstRanker.com - FirstRanker's Choice
GATE 2018 General Aptitude (GA) Set-2
GA 1/3
Q. 1 ? Q. 5 carry one mark each.
Q.1 ?The dress _________ her so well that they all immediately _________ her on her
appearance.?
The words that best fill the blanks in the above sentence are
(A) complemented, complemented (B) complimented, complemented
(C) complimented, complimented (D) complemented, complimented
Q.2 ?The judge?s standing in the legal community, though shaken by false allegations of
wrongdoing, remained _________.?
The word that best fills the blank in the above sentence is
(A) undiminished (B) damaged (C) illegal (D) uncertain
Q.3 Find the missing group of letters in the following series:
BC, FGH, LMNO, _____
(A) UVWXY (B) TUVWX (C) STUVW (D) RSTUV
Q.4 The perimeters of a circle, a square and an equilateral triangle are equal. Which one of the
following statements is true?
(A) The circle has the largest area.
(B) The square has the largest area.
(C) The equilateral triangle has the largest area.
(D) All the three shapes have the same area.
Q.5
The value of the expression
1
1 + log
?? ????
+
1
1 + log
?? ????
+
1
1 + log
?? ????
is _________.
(A) -1 (B) 0 (C) 1 (D) 3
Q. 6 ? Q. 10 carry two marks each.
Q.6 Forty students watched films A, B and C over a week. Each student watched either only
one film or all three. Thirteen students watched film A, sixteen students watched film B
and nineteen students watched film C. How many students watched all three films?
(A) 0 (B) 2 (C) 4 (D) 8
GATE 2018 General Aptitude (GA) Set-2
GA 2/3
Q.7 A wire would enclose an area of 1936 m
2
, if it is bent into a square. The wire is cut into
two pieces. The longer piece is thrice as long as the shorter piece. The long and the short
pieces are bent into a square and a circle, respectively. Which of the following choices is
closest to the sum of the areas enclosed by the two pieces in square meters?
(A) 1096 (B) 1111 (C) 1243 (D) 2486
Q.8 A contract is to be completed in 52 days and 125 identical robots were employed, each
operational for 7 hours a day. After 39 days, five-seventh of the work was completed. How
many additional robots would be required to complete the work on time, if each robot is
now operational for 8 hours a day?
(A) 50 (B) 89 (C) 146 (D) 175
Q.9 A house has a number which needs to be identified. The following three statements are
given that can help in identifying the house number.
i. If the house number is a multiple of 3, then it is a number from 50 to 59.
ii. If the house number is NOT a multiple of 4, then it is a number from 60 to 69.
iii. If the house number is NOT a multiple of 6, then it is a number from 70 to 79.
What is the house number?
(A) 54 (B) 65 (C) 66 (D) 76
GATE 2018 General Aptitude (GA) Set-2
GA 3/3
Q.10 An unbiased coin is tossed six times in a row and four different such trials are conducted.
One trial implies six tosses of the coin. If H stands for head and T stands for tail, the
following are the observations from the four trials:
(1) HTHTHT (2) TTHHHT (3) HTTHHT (4) HHHT__ __.
Which statement describing the last two coin tosses of the fourth trial has the highest
probability of being correct?
(A) Two T will occur.
(B) One H and one T will occur.
(C) Two H will occur.
(D) One H will be followed by one T.
END OF THE QUESTION PAPER
GATE 2018 Aerospace Engineering
AE 1/9
Q. 1 ? Q. 25 carry one mark each.
Q.1
Let ?? ? , ?? ? ?
be two distinct vectors that are not parallel. The vector ?? ? = ?? ? ? ?? ? ?
is
(A) zero. (B) orthogonal to ?? ? alone.
(C) orthogonal to ?? ? + ?? ? ?
. (D) orthogonal to ?? ? ?
alone.
Q.2
Consider the function ?? (?? , ?? ) =
?? 2
2
+
?? 2
3
? 5. All the roots of this function
(A) form a finite set of points.
(B) lie on an elliptical curve.
(C) lie on the surface of a sphere.
(D) lie on a hyperbolic curve.
Q.3
Consider a vector field given by ?? ?? ? + ?? ?? ? + ?? ?? ?
. This vector field is
(A) divergence-free and curl-free.
(B) curl-free but not divergence-free.
(C) divergence-free but not curl-free.
(D) neither divergence-free nor curl-free.
Q.4 A jet aircraft is initially flying steady and level at its maximum endurance condition. For the
aircraft to fly steady and level, but faster at the same altitude, the pilot should
(A) increase thrust alone.
(B) increase thrust and increase angle of attack.
(C) increase thrust and reduce angle of attack.
(D) reduce angle of attack alone.
Q.5 The pilot of a conventional airplane that is flying steady and level at some altitude, deflects
the port side aileron up and the starboard aileron down. The aircraft will then
(A) pitch, nose up.
(B) roll with the starboard wing up.
(C) pitch, nose down.
(D) roll with the port wing up.
Q.6 A NACA 0012 airfoil has a trailing edge flap. The airfoil is operating at an angle of attack
of 5 degrees with un-deflected flap. If the flap is now deflected by 5 degrees downwards, the
?? ?? versus ?? curve
(A) shifts right and slope increases.
(B) shifts left and slope increases.
(C) shifts left and slope stays the same.
(D) shifts right and slope stays the same.
GATE 2018 Aerospace Engineering
AE 2/9
Q.7 An airplane requires a longer ground roll to lift-off on hot summer days because
(A) the thrust is directly proportional to free-stream density.
(B) the thrust is directly proportional to weight of the aircraft.
(C) the lift-off distance is directly proportional to free-stream density.
(D) the runway friction is high on hot summer days.
Q.8 The velocity profile in an incompressible, laminar boundary layer is shown in the figure
below. U is the free-stream velocity, u(y) is the stream-wise velocity component. The area
of the black shaded region in the figure below represents the
y
(A) boundary layer thickness.
(B) momentum thickness.
(C) displacement thickness.
(D) shape factor.
Q.9 The tangential velocity component ?V? of a spacecraft, which is in a circular orbit of radius
?R? around a spherical Earth (? = GM ? gravitational parameter of Earth) is given by the
following expression.
(A) ?? = ?
?
2?? (B) ?? = ?
?
??
(C) ?? =
2?? ??
?? 3
2
(D) ?? =
2?? ??
?? 2
3
Q.10 Equation of the trajectory of a typical space object around any planet, in polar coordinates
(r, ?) (i.e. a general conic section geometry), is given as follows. (h is angular momentum,
? is gravitational parameter, e is eccentricity, r is radial distance from the planet center, ?,
is angle between vectors ?? ? and ?? ?.
(A) ?? =
(
?
2
?
? )
1??? ?????? ?
(B) ?? =
(
?
2
?
? )
?? ??????? ?
(C) ?? =
(
?
2
?
? )
1+?? ?????? ?
(D) ?? =
(
?
2
?
? )
?? +?????? ?
Q.11 In an elliptic orbit around any planet, the location at which a spacecraft has the maximum
angular velocity is
(A) apoapsis. (B) periapsis.
(C) a point at +45
o
from periapsis. (D) a point at ?90
o
from apoapsis.
u(y)/U
GATE 2018 Aerospace Engineering
AE 3/9
Q.12 The pitching moment of a positively cambered NACA airfoil about its leading edge at zero-
lift angle of attack is
(A) negative.
(B) positive.
(C) indeterminate.
(D) zero.
Q.13 In a low-speed wind tunnel, the angular location(s) from the front stagnation point on a
circular cylinder where the static pressure equals the free-stream static pressure, is
(A) ? 38
0
(B) ? 30
0
(C) ? 60
0
(D) 0
0
Q.14 A thermocouple, mounted flush in an insulated flat surface in a supersonic laminar flow of
air measures the
(A) static temperature.
(B) temperature greater than static but less than total temperature.
(C) total temperature.
(D) temperature greater than total temperature.
Q.15 A shock wave is moving into still air in a shock tube. Which one of the following happens
to the air?
(A) static temperature increases, total temperature remains constant.
(B) static temperature increases, total temperature increases.
(C) static temperature increases, total temperature decreases.
(D) static pressure increases, total temperature remains constant.
Q.16 The highest limit load factor experienced by a civil transport aircraft is in the range
(A) 0.0 ? 2.0 (B) 2.0 ? 5.0 (C) 5.0 ? 8.0 (D) 8.0 ? 10.0
Q.17 Determine the correctness or otherwise of the following statements, [a] and [r]:
[a] A closed-section box beam configuration is used in aircraft wings.
[r] Closed-section box beam configuration is capable of resisting torsional loads.
(A) Both [a] and [r] are true and [r] is the correct reason for [a].
(B) Both [a] and [r] are true but [r] is not the correct reason for [a].
(C) Both [a] and [r] are false.
(D) [a] is true but [r] is false.
GATE 2018 Aerospace Engineering
AE 4/9
Q.18 The first law of thermodynamics is also known as conservation of
(A) mass.
(B) momentum.
(C) energy.
(D) species.
Q.19 In an ideal gas turbine cycle, the expansion in a turbine is represented by
(A) an isenthalpic process. (B) an isentropic process.
(C) an isobaric process. (D) an isochoric process.
Q.20
The determinant of the matrix [
1 1 ?1
2 1 0
3 1 1
] is ______ (accurate to one decimal place).
Q.21 The theoretical maximum velocity (in m/s) of air expanding from a reservoir at 700 K is
__________ (accurate to two decimal places). Specific heat of air at constant pressure is
1005 J/(kg-K).
Q.22 For a damped single degree of freedom system with damping ratio of 0.1, ratio of two
successive peak amplitudes of free vibration is ___________ (accurate to two decimal
places).
Q.23 The natural frequency (in rad/s) of the spring-mass system shown in the figure below is
_____ (accurate to one decimal place).
Q.24 The stagnation pressures at the inlet and exit of a subsonic intake are 100 kPa and 98 kPa,
respectively. The pressure recovery of this intake will be ______ (accurate to two decimal
places).
Q.25 A combustor is operating with a fuel-air ratio of 0.03. If the stoichiometric fuel-air ratio of
the fuel used is 0.06, the equivalence ratio of the combustor will be _______ (accurate to
two decimal places).
GATE 2018 Aerospace Engineering
AE 5/9
Q. 26 ? Q. 55 carry two marks each.
Q.26
The solution of the differential equation
?? 2
?? ?? ?? 2
+ 3
????
????
= 0, given that ?? = 0 and
????
????
= 1 at
?? = 0 is
(A) ?? (1 ? ?? ?3?? )
(B)
1
3
(1 ? ?? ?3?? ) (C)
1
3
(1 + ?? ?3?? )
(D)
1
3
????
?3?? 2
Q.27 The relation between pressure (p) and velocity (V) for a steady, isentropic flow at two points
along a streamline is, (c is a constant)
(A) ?? (?? 2
?? ? ?? 1
?? ) =
?? 1
2
2
?
?? 2
2
2
(B) ?? (?? 2
?? ?? ?1
? ?? 1
?? ?? ?1
) =
?? 1
2
2
?
?? 2
2
2
(C) ?? (?? 2
?? ?1
?? ? ?? 1
?? ?1
?? ) =
?? 1
2
2
?
?? 2
2
2
(D) ?? (?? 2
?? ?1
? ?? 1
?? ?1
) =
?? 1
2
2
?
?? 2
2
2
Q.28 A thin airfoil is mounted in a low-speed, subsonic wind tunnel, in which the Mach number
is 0.1. At a point on the airfoil, the pressure coefficient is measured to be ?1.2. If the flow
velocity is increased such that the free-stream Mach number is 0.6, the pressure coefficient
at the same point on the airfoil will approximately be:
(A) ?3.5 (B) ?2.9 (C) ?1.5 (D) ?0.75
Q.29 A solid circular shaft of diameter d is under pure torsion of magnitude T. The maximum
tensile stress experienced at any point on the shaft is
(A)
32?? ?? ?? 3
(B)
16?? ?? ?? 4
(C)
32?? ?? ?? 4
(D)
16?? ?? ?? 3
Q.30 A clamped-clamped beam, subjected to a point load P at the midspan, is shown in the figure
below. The magnitude of the moment reaction at the two fixed ends of the beam is
(A) PL/2 (B) PL/4 (C) PL/8 (D) PL/16
GATE 2018 Aerospace Engineering
AE 6/9
Q.31 Which of the following statement(s) is/are true about the state of a body in plane strain
condition?
P: All the points in the body undergo displacements in one plane only, for example the x-y
plane, leading to ?? ????
= ?? ????
= ?? ????
= 0.
Q: All the components of stress perpendicular to the plane of deformation, for example the
x-y plane, of the body are equal to zero, i.e. ?? ????
= ?? ????
= ?? ????
= 0.
R: Except the normal component, all the other components of stress perpendicular to the
plane of deformation of the body, for example the x-y plane, are equal to zero, i.e. ?? ????
? 0,
?? ????
= ?? ????
= 0.
(A) P only (B) Q only (C) P and Q (D) P and R
Q.32 An aircraft with a turbojet engine flies at a velocity of 100 m/s. If the jet exhaust velocity is
300 m/s, the propulsive efficiency of the engine, assuming a negligible fuel-air ratio, is
(A) 0.33 (B) 0.50 (C) 0.67 (D) 0.80
Q.33 An aircraft with a turboprop engine produces a thrust of 500 N and flies at 100 m/s. If the
propeller efficiency is 0.5, the shaft power produced by the engine is
(A) 50 kW (B) 100 kW
(C) 125 kW (D) 500 kW
Q.34 An axial compressor that generates a stagnation pressure ratio of 4.0, operates with inlet and
exit stagnation temperatures of 300 K and 480 K, respectively. If the ratio of specific heats
(?? ) is 1.4, the isentropic efficiency of the compressor is
(A) 0.94 (B) 0.81
(C) 0.72 (D) 0.63
Q.35 A rocket has an initial mass of 150 kg. After operating for a duration of 10 s, its final mass
is 50 kg. If the acceleration due to gravity is 9.81 m/s
2
and the thrust produced by the rocket
is 19.62 kN, the specific impulse of the rocket is
(A) 400 s (B) 300 s
(C) 200 s (D) 100 s
Q.36
Consider the vector field ?? ? = ?
?? ?? 2
?? ? +
?? ?? 2
?? ? ; where ?? = ??? 2
+ ?? 2
. The contour integral
? ?? ? ? ???? ? ? ? ??
, where ???? ? ? ? ??
is tangent to the contour that encloses the origin, is __________ (accurate
to two decimal places).
Q.37 The magnitude of the x-component of a unit vector at the point (1, 1) that is normal to equi-
potential lines of the potential function ?? (?? ) =
1
?? 2
+4
, where ?? = ??? 2
+ ?? 2
, is _______
(accurate to two decimal places).
GATE 2018 Aerospace Engineering
AE 7/9
Q.38 Assuming ISA standard sea level conditions (288.16 K, density of 1.225 kg/m
3
,
g = 9.81 m/s
2
, R = 287 J/(kg-K)), the density (in kg/m
3
) of air at Leh, which is at an altitude
of 3500 m above mean sea level is ________ (accurate to two decimal places).
Q.39 Consider a cubical tank of side 2 m with its top open. It is filled with water up to a height of
1 m. Assuming the density of water to be 1000 kg/m
3
, g as 9.81 m/s
2
and the atmospheric
pressure to be 100 kPa, the net hydrostatic force (in kN) on the side face of the tank due to
the air and water is ______ (accurate to two decimal places).
Q.40 An aircraft with mass of 400,000 kg cruises at 240 m/s at an altitude of 10 km. Its lift to drag
ratio at cruise is 15. Assuming g as 9.81 m/s
2
, the power (in MW) needed for it to cruise is
_______ (accurate to two decimal places).
Q.41 A statically-stable aircraft has a ?? ?? ?? = 5 (where the angle of attack, ?, is measured in radians).
The coefficient of moment of the aircraft about the center of gravity is given as
?? ?? ,?? .?? = 0.05 ? 4?? . The mean aerodynamic chord of the aircraft wing is 1 m. The location
(positive towards the nose) of the neutral point of the aircraft from the center of gravity is
______ (in m, accurate to two decimal places).
Q.42 An aircraft with a gross weight of 2000 kg, has a speed of 130 m/s at sea level, where the
conditions are: 1 atmosphere (pressure), 288 K (temperature), and 1.23 kg/m
3
(density). The
speed (in m/s) required by the aircraft at an altitude of 9000 m, where the conditions are:
0.31 atmosphere, 230 K, and 0.47 kg/m
3
, to maintain a steady, level flight is ________
(accurate to two decimal places).
Q.43 A pitot probe on an aircraft in a steady, level flight records a pressure of 55,000 N/m
2
. The
static pressure and density are 45,280 N/m
2
and 0.6 kg/m
3
, respectively. The wing area and
the lift coefficient are 16 m
2
and 2, respectively. The wing loading (in N/m
2
) on this aircraft
is _________ (accurate to one decimal place).
Q.44 A spacecraft forms a circular orbit at an altitude of 150 km above the surface of a spherical
Earth. Assuming the gravitational parameter, ? = 3.986 ? 10
14
m
3
/s
2
and radius of earth,
RE = 6,400 km, the velocity required for the injection of the spacecraft, parallel to the local
horizon, is _______________ (accurate to two decimal places).
Q.45 Air at 50 kPa pressure and 400 K temperature flows in a duct at Mach 3.0. A part of the flow
leaks through an opening on the duct wall into the ambient, where the pressure is 30 kPa.
The maximum Mach number achieved in the discharge is _______ (accurate to two decimal
places). (Ratio of specific heats of air is ?? = 1.4).
FirstRanker.com - FirstRanker's Choice
GATE 2018 General Aptitude (GA) Set-2
GA 1/3
Q. 1 ? Q. 5 carry one mark each.
Q.1 ?The dress _________ her so well that they all immediately _________ her on her
appearance.?
The words that best fill the blanks in the above sentence are
(A) complemented, complemented (B) complimented, complemented
(C) complimented, complimented (D) complemented, complimented
Q.2 ?The judge?s standing in the legal community, though shaken by false allegations of
wrongdoing, remained _________.?
The word that best fills the blank in the above sentence is
(A) undiminished (B) damaged (C) illegal (D) uncertain
Q.3 Find the missing group of letters in the following series:
BC, FGH, LMNO, _____
(A) UVWXY (B) TUVWX (C) STUVW (D) RSTUV
Q.4 The perimeters of a circle, a square and an equilateral triangle are equal. Which one of the
following statements is true?
(A) The circle has the largest area.
(B) The square has the largest area.
(C) The equilateral triangle has the largest area.
(D) All the three shapes have the same area.
Q.5
The value of the expression
1
1 + log
?? ????
+
1
1 + log
?? ????
+
1
1 + log
?? ????
is _________.
(A) -1 (B) 0 (C) 1 (D) 3
Q. 6 ? Q. 10 carry two marks each.
Q.6 Forty students watched films A, B and C over a week. Each student watched either only
one film or all three. Thirteen students watched film A, sixteen students watched film B
and nineteen students watched film C. How many students watched all three films?
(A) 0 (B) 2 (C) 4 (D) 8
GATE 2018 General Aptitude (GA) Set-2
GA 2/3
Q.7 A wire would enclose an area of 1936 m
2
, if it is bent into a square. The wire is cut into
two pieces. The longer piece is thrice as long as the shorter piece. The long and the short
pieces are bent into a square and a circle, respectively. Which of the following choices is
closest to the sum of the areas enclosed by the two pieces in square meters?
(A) 1096 (B) 1111 (C) 1243 (D) 2486
Q.8 A contract is to be completed in 52 days and 125 identical robots were employed, each
operational for 7 hours a day. After 39 days, five-seventh of the work was completed. How
many additional robots would be required to complete the work on time, if each robot is
now operational for 8 hours a day?
(A) 50 (B) 89 (C) 146 (D) 175
Q.9 A house has a number which needs to be identified. The following three statements are
given that can help in identifying the house number.
i. If the house number is a multiple of 3, then it is a number from 50 to 59.
ii. If the house number is NOT a multiple of 4, then it is a number from 60 to 69.
iii. If the house number is NOT a multiple of 6, then it is a number from 70 to 79.
What is the house number?
(A) 54 (B) 65 (C) 66 (D) 76
GATE 2018 General Aptitude (GA) Set-2
GA 3/3
Q.10 An unbiased coin is tossed six times in a row and four different such trials are conducted.
One trial implies six tosses of the coin. If H stands for head and T stands for tail, the
following are the observations from the four trials:
(1) HTHTHT (2) TTHHHT (3) HTTHHT (4) HHHT__ __.
Which statement describing the last two coin tosses of the fourth trial has the highest
probability of being correct?
(A) Two T will occur.
(B) One H and one T will occur.
(C) Two H will occur.
(D) One H will be followed by one T.
END OF THE QUESTION PAPER
GATE 2018 Aerospace Engineering
AE 1/9
Q. 1 ? Q. 25 carry one mark each.
Q.1
Let ?? ? , ?? ? ?
be two distinct vectors that are not parallel. The vector ?? ? = ?? ? ? ?? ? ?
is
(A) zero. (B) orthogonal to ?? ? alone.
(C) orthogonal to ?? ? + ?? ? ?
. (D) orthogonal to ?? ? ?
alone.
Q.2
Consider the function ?? (?? , ?? ) =
?? 2
2
+
?? 2
3
? 5. All the roots of this function
(A) form a finite set of points.
(B) lie on an elliptical curve.
(C) lie on the surface of a sphere.
(D) lie on a hyperbolic curve.
Q.3
Consider a vector field given by ?? ?? ? + ?? ?? ? + ?? ?? ?
. This vector field is
(A) divergence-free and curl-free.
(B) curl-free but not divergence-free.
(C) divergence-free but not curl-free.
(D) neither divergence-free nor curl-free.
Q.4 A jet aircraft is initially flying steady and level at its maximum endurance condition. For the
aircraft to fly steady and level, but faster at the same altitude, the pilot should
(A) increase thrust alone.
(B) increase thrust and increase angle of attack.
(C) increase thrust and reduce angle of attack.
(D) reduce angle of attack alone.
Q.5 The pilot of a conventional airplane that is flying steady and level at some altitude, deflects
the port side aileron up and the starboard aileron down. The aircraft will then
(A) pitch, nose up.
(B) roll with the starboard wing up.
(C) pitch, nose down.
(D) roll with the port wing up.
Q.6 A NACA 0012 airfoil has a trailing edge flap. The airfoil is operating at an angle of attack
of 5 degrees with un-deflected flap. If the flap is now deflected by 5 degrees downwards, the
?? ?? versus ?? curve
(A) shifts right and slope increases.
(B) shifts left and slope increases.
(C) shifts left and slope stays the same.
(D) shifts right and slope stays the same.
GATE 2018 Aerospace Engineering
AE 2/9
Q.7 An airplane requires a longer ground roll to lift-off on hot summer days because
(A) the thrust is directly proportional to free-stream density.
(B) the thrust is directly proportional to weight of the aircraft.
(C) the lift-off distance is directly proportional to free-stream density.
(D) the runway friction is high on hot summer days.
Q.8 The velocity profile in an incompressible, laminar boundary layer is shown in the figure
below. U is the free-stream velocity, u(y) is the stream-wise velocity component. The area
of the black shaded region in the figure below represents the
y
(A) boundary layer thickness.
(B) momentum thickness.
(C) displacement thickness.
(D) shape factor.
Q.9 The tangential velocity component ?V? of a spacecraft, which is in a circular orbit of radius
?R? around a spherical Earth (? = GM ? gravitational parameter of Earth) is given by the
following expression.
(A) ?? = ?
?
2?? (B) ?? = ?
?
??
(C) ?? =
2?? ??
?? 3
2
(D) ?? =
2?? ??
?? 2
3
Q.10 Equation of the trajectory of a typical space object around any planet, in polar coordinates
(r, ?) (i.e. a general conic section geometry), is given as follows. (h is angular momentum,
? is gravitational parameter, e is eccentricity, r is radial distance from the planet center, ?,
is angle between vectors ?? ? and ?? ?.
(A) ?? =
(
?
2
?
? )
1??? ?????? ?
(B) ?? =
(
?
2
?
? )
?? ??????? ?
(C) ?? =
(
?
2
?
? )
1+?? ?????? ?
(D) ?? =
(
?
2
?
? )
?? +?????? ?
Q.11 In an elliptic orbit around any planet, the location at which a spacecraft has the maximum
angular velocity is
(A) apoapsis. (B) periapsis.
(C) a point at +45
o
from periapsis. (D) a point at ?90
o
from apoapsis.
u(y)/U
GATE 2018 Aerospace Engineering
AE 3/9
Q.12 The pitching moment of a positively cambered NACA airfoil about its leading edge at zero-
lift angle of attack is
(A) negative.
(B) positive.
(C) indeterminate.
(D) zero.
Q.13 In a low-speed wind tunnel, the angular location(s) from the front stagnation point on a
circular cylinder where the static pressure equals the free-stream static pressure, is
(A) ? 38
0
(B) ? 30
0
(C) ? 60
0
(D) 0
0
Q.14 A thermocouple, mounted flush in an insulated flat surface in a supersonic laminar flow of
air measures the
(A) static temperature.
(B) temperature greater than static but less than total temperature.
(C) total temperature.
(D) temperature greater than total temperature.
Q.15 A shock wave is moving into still air in a shock tube. Which one of the following happens
to the air?
(A) static temperature increases, total temperature remains constant.
(B) static temperature increases, total temperature increases.
(C) static temperature increases, total temperature decreases.
(D) static pressure increases, total temperature remains constant.
Q.16 The highest limit load factor experienced by a civil transport aircraft is in the range
(A) 0.0 ? 2.0 (B) 2.0 ? 5.0 (C) 5.0 ? 8.0 (D) 8.0 ? 10.0
Q.17 Determine the correctness or otherwise of the following statements, [a] and [r]:
[a] A closed-section box beam configuration is used in aircraft wings.
[r] Closed-section box beam configuration is capable of resisting torsional loads.
(A) Both [a] and [r] are true and [r] is the correct reason for [a].
(B) Both [a] and [r] are true but [r] is not the correct reason for [a].
(C) Both [a] and [r] are false.
(D) [a] is true but [r] is false.
GATE 2018 Aerospace Engineering
AE 4/9
Q.18 The first law of thermodynamics is also known as conservation of
(A) mass.
(B) momentum.
(C) energy.
(D) species.
Q.19 In an ideal gas turbine cycle, the expansion in a turbine is represented by
(A) an isenthalpic process. (B) an isentropic process.
(C) an isobaric process. (D) an isochoric process.
Q.20
The determinant of the matrix [
1 1 ?1
2 1 0
3 1 1
] is ______ (accurate to one decimal place).
Q.21 The theoretical maximum velocity (in m/s) of air expanding from a reservoir at 700 K is
__________ (accurate to two decimal places). Specific heat of air at constant pressure is
1005 J/(kg-K).
Q.22 For a damped single degree of freedom system with damping ratio of 0.1, ratio of two
successive peak amplitudes of free vibration is ___________ (accurate to two decimal
places).
Q.23 The natural frequency (in rad/s) of the spring-mass system shown in the figure below is
_____ (accurate to one decimal place).
Q.24 The stagnation pressures at the inlet and exit of a subsonic intake are 100 kPa and 98 kPa,
respectively. The pressure recovery of this intake will be ______ (accurate to two decimal
places).
Q.25 A combustor is operating with a fuel-air ratio of 0.03. If the stoichiometric fuel-air ratio of
the fuel used is 0.06, the equivalence ratio of the combustor will be _______ (accurate to
two decimal places).
GATE 2018 Aerospace Engineering
AE 5/9
Q. 26 ? Q. 55 carry two marks each.
Q.26
The solution of the differential equation
?? 2
?? ?? ?? 2
+ 3
????
????
= 0, given that ?? = 0 and
????
????
= 1 at
?? = 0 is
(A) ?? (1 ? ?? ?3?? )
(B)
1
3
(1 ? ?? ?3?? ) (C)
1
3
(1 + ?? ?3?? )
(D)
1
3
????
?3?? 2
Q.27 The relation between pressure (p) and velocity (V) for a steady, isentropic flow at two points
along a streamline is, (c is a constant)
(A) ?? (?? 2
?? ? ?? 1
?? ) =
?? 1
2
2
?
?? 2
2
2
(B) ?? (?? 2
?? ?? ?1
? ?? 1
?? ?? ?1
) =
?? 1
2
2
?
?? 2
2
2
(C) ?? (?? 2
?? ?1
?? ? ?? 1
?? ?1
?? ) =
?? 1
2
2
?
?? 2
2
2
(D) ?? (?? 2
?? ?1
? ?? 1
?? ?1
) =
?? 1
2
2
?
?? 2
2
2
Q.28 A thin airfoil is mounted in a low-speed, subsonic wind tunnel, in which the Mach number
is 0.1. At a point on the airfoil, the pressure coefficient is measured to be ?1.2. If the flow
velocity is increased such that the free-stream Mach number is 0.6, the pressure coefficient
at the same point on the airfoil will approximately be:
(A) ?3.5 (B) ?2.9 (C) ?1.5 (D) ?0.75
Q.29 A solid circular shaft of diameter d is under pure torsion of magnitude T. The maximum
tensile stress experienced at any point on the shaft is
(A)
32?? ?? ?? 3
(B)
16?? ?? ?? 4
(C)
32?? ?? ?? 4
(D)
16?? ?? ?? 3
Q.30 A clamped-clamped beam, subjected to a point load P at the midspan, is shown in the figure
below. The magnitude of the moment reaction at the two fixed ends of the beam is
(A) PL/2 (B) PL/4 (C) PL/8 (D) PL/16
GATE 2018 Aerospace Engineering
AE 6/9
Q.31 Which of the following statement(s) is/are true about the state of a body in plane strain
condition?
P: All the points in the body undergo displacements in one plane only, for example the x-y
plane, leading to ?? ????
= ?? ????
= ?? ????
= 0.
Q: All the components of stress perpendicular to the plane of deformation, for example the
x-y plane, of the body are equal to zero, i.e. ?? ????
= ?? ????
= ?? ????
= 0.
R: Except the normal component, all the other components of stress perpendicular to the
plane of deformation of the body, for example the x-y plane, are equal to zero, i.e. ?? ????
? 0,
?? ????
= ?? ????
= 0.
(A) P only (B) Q only (C) P and Q (D) P and R
Q.32 An aircraft with a turbojet engine flies at a velocity of 100 m/s. If the jet exhaust velocity is
300 m/s, the propulsive efficiency of the engine, assuming a negligible fuel-air ratio, is
(A) 0.33 (B) 0.50 (C) 0.67 (D) 0.80
Q.33 An aircraft with a turboprop engine produces a thrust of 500 N and flies at 100 m/s. If the
propeller efficiency is 0.5, the shaft power produced by the engine is
(A) 50 kW (B) 100 kW
(C) 125 kW (D) 500 kW
Q.34 An axial compressor that generates a stagnation pressure ratio of 4.0, operates with inlet and
exit stagnation temperatures of 300 K and 480 K, respectively. If the ratio of specific heats
(?? ) is 1.4, the isentropic efficiency of the compressor is
(A) 0.94 (B) 0.81
(C) 0.72 (D) 0.63
Q.35 A rocket has an initial mass of 150 kg. After operating for a duration of 10 s, its final mass
is 50 kg. If the acceleration due to gravity is 9.81 m/s
2
and the thrust produced by the rocket
is 19.62 kN, the specific impulse of the rocket is
(A) 400 s (B) 300 s
(C) 200 s (D) 100 s
Q.36
Consider the vector field ?? ? = ?
?? ?? 2
?? ? +
?? ?? 2
?? ? ; where ?? = ??? 2
+ ?? 2
. The contour integral
? ?? ? ? ???? ? ? ? ??
, where ???? ? ? ? ??
is tangent to the contour that encloses the origin, is __________ (accurate
to two decimal places).
Q.37 The magnitude of the x-component of a unit vector at the point (1, 1) that is normal to equi-
potential lines of the potential function ?? (?? ) =
1
?? 2
+4
, where ?? = ??? 2
+ ?? 2
, is _______
(accurate to two decimal places).
GATE 2018 Aerospace Engineering
AE 7/9
Q.38 Assuming ISA standard sea level conditions (288.16 K, density of 1.225 kg/m
3
,
g = 9.81 m/s
2
, R = 287 J/(kg-K)), the density (in kg/m
3
) of air at Leh, which is at an altitude
of 3500 m above mean sea level is ________ (accurate to two decimal places).
Q.39 Consider a cubical tank of side 2 m with its top open. It is filled with water up to a height of
1 m. Assuming the density of water to be 1000 kg/m
3
, g as 9.81 m/s
2
and the atmospheric
pressure to be 100 kPa, the net hydrostatic force (in kN) on the side face of the tank due to
the air and water is ______ (accurate to two decimal places).
Q.40 An aircraft with mass of 400,000 kg cruises at 240 m/s at an altitude of 10 km. Its lift to drag
ratio at cruise is 15. Assuming g as 9.81 m/s
2
, the power (in MW) needed for it to cruise is
_______ (accurate to two decimal places).
Q.41 A statically-stable aircraft has a ?? ?? ?? = 5 (where the angle of attack, ?, is measured in radians).
The coefficient of moment of the aircraft about the center of gravity is given as
?? ?? ,?? .?? = 0.05 ? 4?? . The mean aerodynamic chord of the aircraft wing is 1 m. The location
(positive towards the nose) of the neutral point of the aircraft from the center of gravity is
______ (in m, accurate to two decimal places).
Q.42 An aircraft with a gross weight of 2000 kg, has a speed of 130 m/s at sea level, where the
conditions are: 1 atmosphere (pressure), 288 K (temperature), and 1.23 kg/m
3
(density). The
speed (in m/s) required by the aircraft at an altitude of 9000 m, where the conditions are:
0.31 atmosphere, 230 K, and 0.47 kg/m
3
, to maintain a steady, level flight is ________
(accurate to two decimal places).
Q.43 A pitot probe on an aircraft in a steady, level flight records a pressure of 55,000 N/m
2
. The
static pressure and density are 45,280 N/m
2
and 0.6 kg/m
3
, respectively. The wing area and
the lift coefficient are 16 m
2
and 2, respectively. The wing loading (in N/m
2
) on this aircraft
is _________ (accurate to one decimal place).
Q.44 A spacecraft forms a circular orbit at an altitude of 150 km above the surface of a spherical
Earth. Assuming the gravitational parameter, ? = 3.986 ? 10
14
m
3
/s
2
and radius of earth,
RE = 6,400 km, the velocity required for the injection of the spacecraft, parallel to the local
horizon, is _______________ (accurate to two decimal places).
Q.45 Air at 50 kPa pressure and 400 K temperature flows in a duct at Mach 3.0. A part of the flow
leaks through an opening on the duct wall into the ambient, where the pressure is 30 kPa.
The maximum Mach number achieved in the discharge is _______ (accurate to two decimal
places). (Ratio of specific heats of air is ?? = 1.4).
GATE 2018 Aerospace Engineering
AE 8/9
Q.46 Consider a 20
0
half-angle wedge in a supersonic flow at Mach 3.0 at standard sea-level
conditions. If the shock-wave angle on the wedge is 36
0
, the Mach number of the tangential
component of the flow post-shock is _______ (accurate to two decimal places).
Q.47 The boundary layer thickness at the location of a sensor on a flat plate in an incompressible,
laminar flow of air is required to be restricted to 1 mm for an effective measurement. If the
flow velocity is 20 m/s with 1 bar pressure, 300 K temperature, and 1.789?10
?5
kg/(m-s)
viscosity, the maximum distance (in mm) of the sensor location from the leading edge is
________ (accurate to one decimal place).
Q.48 Gross weight of an airplane is 7000 N, wing area is 16 m
2
,
and the maximum lift coefficient
is 2.0. Assuming density at the altitude as 1.23 kg/m
3
, the stall speed (in m/s) of the aircraft
is _________ (accurate to two decimal places).
Q.49 A thin-walled tube with external radius of 100 mm and wall thickness of 2 mm, is fixed at
one end. It is subjected to a compressive force of 1 N acting at a point on the circumference
parallel to its length. The maximum normal stress (in kPa) experienced by the structure is
_____________ (accurate to two decimal places).
Q.50 A 1 m long massless cantilever beam oscillates at 2Hz, while a 60 kg mass is attached at the
tip of it. The flexural rigidity of the beam (in kN-m
2
) is _________________ (accurate to
two decimal places).
Q.51 A cantilever beam having a rectangular cross-section of width 60 mm and depth 100 mm, is
made of aluminum alloy. The material mechanical properties are: Young?s modulus,
E = 73 GPa and ultimate stress, ?? ?? = 480 MPa. Assuming a factor of safety of 4, the
maximum bending moment (in kN-m) that can be applied on the beam is _____ (accurate to
one decimal place).
Q.52 The components of stress in a body under plane stress condition, in the absence of body
forces, is given by:
?? ????
= ?? ?? 2
; ?? ????
= 12?? 2
? 6?? 2
and ?? ????
= 12???? .
The coefficient, A, such that the body is under equilibrium is _____ (accurate to one decimal
place).
Q.53 An axial compressor rotor with 50 % degree of reaction, operates with an axial velocity of
200 m/s. The absolute flow angle at the inlet of the rotor is 22
o
with reference to the axial
direction. If the axial velocity is assumed to remain constant through the rotor, the magnitude
of the relative velocity (in m/s) at the rotor exit is __________ (accurate to one decimal
place).
FirstRanker.com - FirstRanker's Choice
GATE 2018 General Aptitude (GA) Set-2
GA 1/3
Q. 1 ? Q. 5 carry one mark each.
Q.1 ?The dress _________ her so well that they all immediately _________ her on her
appearance.?
The words that best fill the blanks in the above sentence are
(A) complemented, complemented (B) complimented, complemented
(C) complimented, complimented (D) complemented, complimented
Q.2 ?The judge?s standing in the legal community, though shaken by false allegations of
wrongdoing, remained _________.?
The word that best fills the blank in the above sentence is
(A) undiminished (B) damaged (C) illegal (D) uncertain
Q.3 Find the missing group of letters in the following series:
BC, FGH, LMNO, _____
(A) UVWXY (B) TUVWX (C) STUVW (D) RSTUV
Q.4 The perimeters of a circle, a square and an equilateral triangle are equal. Which one of the
following statements is true?
(A) The circle has the largest area.
(B) The square has the largest area.
(C) The equilateral triangle has the largest area.
(D) All the three shapes have the same area.
Q.5
The value of the expression
1
1 + log
?? ????
+
1
1 + log
?? ????
+
1
1 + log
?? ????
is _________.
(A) -1 (B) 0 (C) 1 (D) 3
Q. 6 ? Q. 10 carry two marks each.
Q.6 Forty students watched films A, B and C over a week. Each student watched either only
one film or all three. Thirteen students watched film A, sixteen students watched film B
and nineteen students watched film C. How many students watched all three films?
(A) 0 (B) 2 (C) 4 (D) 8
GATE 2018 General Aptitude (GA) Set-2
GA 2/3
Q.7 A wire would enclose an area of 1936 m
2
, if it is bent into a square. The wire is cut into
two pieces. The longer piece is thrice as long as the shorter piece. The long and the short
pieces are bent into a square and a circle, respectively. Which of the following choices is
closest to the sum of the areas enclosed by the two pieces in square meters?
(A) 1096 (B) 1111 (C) 1243 (D) 2486
Q.8 A contract is to be completed in 52 days and 125 identical robots were employed, each
operational for 7 hours a day. After 39 days, five-seventh of the work was completed. How
many additional robots would be required to complete the work on time, if each robot is
now operational for 8 hours a day?
(A) 50 (B) 89 (C) 146 (D) 175
Q.9 A house has a number which needs to be identified. The following three statements are
given that can help in identifying the house number.
i. If the house number is a multiple of 3, then it is a number from 50 to 59.
ii. If the house number is NOT a multiple of 4, then it is a number from 60 to 69.
iii. If the house number is NOT a multiple of 6, then it is a number from 70 to 79.
What is the house number?
(A) 54 (B) 65 (C) 66 (D) 76
GATE 2018 General Aptitude (GA) Set-2
GA 3/3
Q.10 An unbiased coin is tossed six times in a row and four different such trials are conducted.
One trial implies six tosses of the coin. If H stands for head and T stands for tail, the
following are the observations from the four trials:
(1) HTHTHT (2) TTHHHT (3) HTTHHT (4) HHHT__ __.
Which statement describing the last two coin tosses of the fourth trial has the highest
probability of being correct?
(A) Two T will occur.
(B) One H and one T will occur.
(C) Two H will occur.
(D) One H will be followed by one T.
END OF THE QUESTION PAPER
GATE 2018 Aerospace Engineering
AE 1/9
Q. 1 ? Q. 25 carry one mark each.
Q.1
Let ?? ? , ?? ? ?
be two distinct vectors that are not parallel. The vector ?? ? = ?? ? ? ?? ? ?
is
(A) zero. (B) orthogonal to ?? ? alone.
(C) orthogonal to ?? ? + ?? ? ?
. (D) orthogonal to ?? ? ?
alone.
Q.2
Consider the function ?? (?? , ?? ) =
?? 2
2
+
?? 2
3
? 5. All the roots of this function
(A) form a finite set of points.
(B) lie on an elliptical curve.
(C) lie on the surface of a sphere.
(D) lie on a hyperbolic curve.
Q.3
Consider a vector field given by ?? ?? ? + ?? ?? ? + ?? ?? ?
. This vector field is
(A) divergence-free and curl-free.
(B) curl-free but not divergence-free.
(C) divergence-free but not curl-free.
(D) neither divergence-free nor curl-free.
Q.4 A jet aircraft is initially flying steady and level at its maximum endurance condition. For the
aircraft to fly steady and level, but faster at the same altitude, the pilot should
(A) increase thrust alone.
(B) increase thrust and increase angle of attack.
(C) increase thrust and reduce angle of attack.
(D) reduce angle of attack alone.
Q.5 The pilot of a conventional airplane that is flying steady and level at some altitude, deflects
the port side aileron up and the starboard aileron down. The aircraft will then
(A) pitch, nose up.
(B) roll with the starboard wing up.
(C) pitch, nose down.
(D) roll with the port wing up.
Q.6 A NACA 0012 airfoil has a trailing edge flap. The airfoil is operating at an angle of attack
of 5 degrees with un-deflected flap. If the flap is now deflected by 5 degrees downwards, the
?? ?? versus ?? curve
(A) shifts right and slope increases.
(B) shifts left and slope increases.
(C) shifts left and slope stays the same.
(D) shifts right and slope stays the same.
GATE 2018 Aerospace Engineering
AE 2/9
Q.7 An airplane requires a longer ground roll to lift-off on hot summer days because
(A) the thrust is directly proportional to free-stream density.
(B) the thrust is directly proportional to weight of the aircraft.
(C) the lift-off distance is directly proportional to free-stream density.
(D) the runway friction is high on hot summer days.
Q.8 The velocity profile in an incompressible, laminar boundary layer is shown in the figure
below. U is the free-stream velocity, u(y) is the stream-wise velocity component. The area
of the black shaded region in the figure below represents the
y
(A) boundary layer thickness.
(B) momentum thickness.
(C) displacement thickness.
(D) shape factor.
Q.9 The tangential velocity component ?V? of a spacecraft, which is in a circular orbit of radius
?R? around a spherical Earth (? = GM ? gravitational parameter of Earth) is given by the
following expression.
(A) ?? = ?
?
2?? (B) ?? = ?
?
??
(C) ?? =
2?? ??
?? 3
2
(D) ?? =
2?? ??
?? 2
3
Q.10 Equation of the trajectory of a typical space object around any planet, in polar coordinates
(r, ?) (i.e. a general conic section geometry), is given as follows. (h is angular momentum,
? is gravitational parameter, e is eccentricity, r is radial distance from the planet center, ?,
is angle between vectors ?? ? and ?? ?.
(A) ?? =
(
?
2
?
? )
1??? ?????? ?
(B) ?? =
(
?
2
?
? )
?? ??????? ?
(C) ?? =
(
?
2
?
? )
1+?? ?????? ?
(D) ?? =
(
?
2
?
? )
?? +?????? ?
Q.11 In an elliptic orbit around any planet, the location at which a spacecraft has the maximum
angular velocity is
(A) apoapsis. (B) periapsis.
(C) a point at +45
o
from periapsis. (D) a point at ?90
o
from apoapsis.
u(y)/U
GATE 2018 Aerospace Engineering
AE 3/9
Q.12 The pitching moment of a positively cambered NACA airfoil about its leading edge at zero-
lift angle of attack is
(A) negative.
(B) positive.
(C) indeterminate.
(D) zero.
Q.13 In a low-speed wind tunnel, the angular location(s) from the front stagnation point on a
circular cylinder where the static pressure equals the free-stream static pressure, is
(A) ? 38
0
(B) ? 30
0
(C) ? 60
0
(D) 0
0
Q.14 A thermocouple, mounted flush in an insulated flat surface in a supersonic laminar flow of
air measures the
(A) static temperature.
(B) temperature greater than static but less than total temperature.
(C) total temperature.
(D) temperature greater than total temperature.
Q.15 A shock wave is moving into still air in a shock tube. Which one of the following happens
to the air?
(A) static temperature increases, total temperature remains constant.
(B) static temperature increases, total temperature increases.
(C) static temperature increases, total temperature decreases.
(D) static pressure increases, total temperature remains constant.
Q.16 The highest limit load factor experienced by a civil transport aircraft is in the range
(A) 0.0 ? 2.0 (B) 2.0 ? 5.0 (C) 5.0 ? 8.0 (D) 8.0 ? 10.0
Q.17 Determine the correctness or otherwise of the following statements, [a] and [r]:
[a] A closed-section box beam configuration is used in aircraft wings.
[r] Closed-section box beam configuration is capable of resisting torsional loads.
(A) Both [a] and [r] are true and [r] is the correct reason for [a].
(B) Both [a] and [r] are true but [r] is not the correct reason for [a].
(C) Both [a] and [r] are false.
(D) [a] is true but [r] is false.
GATE 2018 Aerospace Engineering
AE 4/9
Q.18 The first law of thermodynamics is also known as conservation of
(A) mass.
(B) momentum.
(C) energy.
(D) species.
Q.19 In an ideal gas turbine cycle, the expansion in a turbine is represented by
(A) an isenthalpic process. (B) an isentropic process.
(C) an isobaric process. (D) an isochoric process.
Q.20
The determinant of the matrix [
1 1 ?1
2 1 0
3 1 1
] is ______ (accurate to one decimal place).
Q.21 The theoretical maximum velocity (in m/s) of air expanding from a reservoir at 700 K is
__________ (accurate to two decimal places). Specific heat of air at constant pressure is
1005 J/(kg-K).
Q.22 For a damped single degree of freedom system with damping ratio of 0.1, ratio of two
successive peak amplitudes of free vibration is ___________ (accurate to two decimal
places).
Q.23 The natural frequency (in rad/s) of the spring-mass system shown in the figure below is
_____ (accurate to one decimal place).
Q.24 The stagnation pressures at the inlet and exit of a subsonic intake are 100 kPa and 98 kPa,
respectively. The pressure recovery of this intake will be ______ (accurate to two decimal
places).
Q.25 A combustor is operating with a fuel-air ratio of 0.03. If the stoichiometric fuel-air ratio of
the fuel used is 0.06, the equivalence ratio of the combustor will be _______ (accurate to
two decimal places).
GATE 2018 Aerospace Engineering
AE 5/9
Q. 26 ? Q. 55 carry two marks each.
Q.26
The solution of the differential equation
?? 2
?? ?? ?? 2
+ 3
????
????
= 0, given that ?? = 0 and
????
????
= 1 at
?? = 0 is
(A) ?? (1 ? ?? ?3?? )
(B)
1
3
(1 ? ?? ?3?? ) (C)
1
3
(1 + ?? ?3?? )
(D)
1
3
????
?3?? 2
Q.27 The relation between pressure (p) and velocity (V) for a steady, isentropic flow at two points
along a streamline is, (c is a constant)
(A) ?? (?? 2
?? ? ?? 1
?? ) =
?? 1
2
2
?
?? 2
2
2
(B) ?? (?? 2
?? ?? ?1
? ?? 1
?? ?? ?1
) =
?? 1
2
2
?
?? 2
2
2
(C) ?? (?? 2
?? ?1
?? ? ?? 1
?? ?1
?? ) =
?? 1
2
2
?
?? 2
2
2
(D) ?? (?? 2
?? ?1
? ?? 1
?? ?1
) =
?? 1
2
2
?
?? 2
2
2
Q.28 A thin airfoil is mounted in a low-speed, subsonic wind tunnel, in which the Mach number
is 0.1. At a point on the airfoil, the pressure coefficient is measured to be ?1.2. If the flow
velocity is increased such that the free-stream Mach number is 0.6, the pressure coefficient
at the same point on the airfoil will approximately be:
(A) ?3.5 (B) ?2.9 (C) ?1.5 (D) ?0.75
Q.29 A solid circular shaft of diameter d is under pure torsion of magnitude T. The maximum
tensile stress experienced at any point on the shaft is
(A)
32?? ?? ?? 3
(B)
16?? ?? ?? 4
(C)
32?? ?? ?? 4
(D)
16?? ?? ?? 3
Q.30 A clamped-clamped beam, subjected to a point load P at the midspan, is shown in the figure
below. The magnitude of the moment reaction at the two fixed ends of the beam is
(A) PL/2 (B) PL/4 (C) PL/8 (D) PL/16
GATE 2018 Aerospace Engineering
AE 6/9
Q.31 Which of the following statement(s) is/are true about the state of a body in plane strain
condition?
P: All the points in the body undergo displacements in one plane only, for example the x-y
plane, leading to ?? ????
= ?? ????
= ?? ????
= 0.
Q: All the components of stress perpendicular to the plane of deformation, for example the
x-y plane, of the body are equal to zero, i.e. ?? ????
= ?? ????
= ?? ????
= 0.
R: Except the normal component, all the other components of stress perpendicular to the
plane of deformation of the body, for example the x-y plane, are equal to zero, i.e. ?? ????
? 0,
?? ????
= ?? ????
= 0.
(A) P only (B) Q only (C) P and Q (D) P and R
Q.32 An aircraft with a turbojet engine flies at a velocity of 100 m/s. If the jet exhaust velocity is
300 m/s, the propulsive efficiency of the engine, assuming a negligible fuel-air ratio, is
(A) 0.33 (B) 0.50 (C) 0.67 (D) 0.80
Q.33 An aircraft with a turboprop engine produces a thrust of 500 N and flies at 100 m/s. If the
propeller efficiency is 0.5, the shaft power produced by the engine is
(A) 50 kW (B) 100 kW
(C) 125 kW (D) 500 kW
Q.34 An axial compressor that generates a stagnation pressure ratio of 4.0, operates with inlet and
exit stagnation temperatures of 300 K and 480 K, respectively. If the ratio of specific heats
(?? ) is 1.4, the isentropic efficiency of the compressor is
(A) 0.94 (B) 0.81
(C) 0.72 (D) 0.63
Q.35 A rocket has an initial mass of 150 kg. After operating for a duration of 10 s, its final mass
is 50 kg. If the acceleration due to gravity is 9.81 m/s
2
and the thrust produced by the rocket
is 19.62 kN, the specific impulse of the rocket is
(A) 400 s (B) 300 s
(C) 200 s (D) 100 s
Q.36
Consider the vector field ?? ? = ?
?? ?? 2
?? ? +
?? ?? 2
?? ? ; where ?? = ??? 2
+ ?? 2
. The contour integral
? ?? ? ? ???? ? ? ? ??
, where ???? ? ? ? ??
is tangent to the contour that encloses the origin, is __________ (accurate
to two decimal places).
Q.37 The magnitude of the x-component of a unit vector at the point (1, 1) that is normal to equi-
potential lines of the potential function ?? (?? ) =
1
?? 2
+4
, where ?? = ??? 2
+ ?? 2
, is _______
(accurate to two decimal places).
GATE 2018 Aerospace Engineering
AE 7/9
Q.38 Assuming ISA standard sea level conditions (288.16 K, density of 1.225 kg/m
3
,
g = 9.81 m/s
2
, R = 287 J/(kg-K)), the density (in kg/m
3
) of air at Leh, which is at an altitude
of 3500 m above mean sea level is ________ (accurate to two decimal places).
Q.39 Consider a cubical tank of side 2 m with its top open. It is filled with water up to a height of
1 m. Assuming the density of water to be 1000 kg/m
3
, g as 9.81 m/s
2
and the atmospheric
pressure to be 100 kPa, the net hydrostatic force (in kN) on the side face of the tank due to
the air and water is ______ (accurate to two decimal places).
Q.40 An aircraft with mass of 400,000 kg cruises at 240 m/s at an altitude of 10 km. Its lift to drag
ratio at cruise is 15. Assuming g as 9.81 m/s
2
, the power (in MW) needed for it to cruise is
_______ (accurate to two decimal places).
Q.41 A statically-stable aircraft has a ?? ?? ?? = 5 (where the angle of attack, ?, is measured in radians).
The coefficient of moment of the aircraft about the center of gravity is given as
?? ?? ,?? .?? = 0.05 ? 4?? . The mean aerodynamic chord of the aircraft wing is 1 m. The location
(positive towards the nose) of the neutral point of the aircraft from the center of gravity is
______ (in m, accurate to two decimal places).
Q.42 An aircraft with a gross weight of 2000 kg, has a speed of 130 m/s at sea level, where the
conditions are: 1 atmosphere (pressure), 288 K (temperature), and 1.23 kg/m
3
(density). The
speed (in m/s) required by the aircraft at an altitude of 9000 m, where the conditions are:
0.31 atmosphere, 230 K, and 0.47 kg/m
3
, to maintain a steady, level flight is ________
(accurate to two decimal places).
Q.43 A pitot probe on an aircraft in a steady, level flight records a pressure of 55,000 N/m
2
. The
static pressure and density are 45,280 N/m
2
and 0.6 kg/m
3
, respectively. The wing area and
the lift coefficient are 16 m
2
and 2, respectively. The wing loading (in N/m
2
) on this aircraft
is _________ (accurate to one decimal place).
Q.44 A spacecraft forms a circular orbit at an altitude of 150 km above the surface of a spherical
Earth. Assuming the gravitational parameter, ? = 3.986 ? 10
14
m
3
/s
2
and radius of earth,
RE = 6,400 km, the velocity required for the injection of the spacecraft, parallel to the local
horizon, is _______________ (accurate to two decimal places).
Q.45 Air at 50 kPa pressure and 400 K temperature flows in a duct at Mach 3.0. A part of the flow
leaks through an opening on the duct wall into the ambient, where the pressure is 30 kPa.
The maximum Mach number achieved in the discharge is _______ (accurate to two decimal
places). (Ratio of specific heats of air is ?? = 1.4).
GATE 2018 Aerospace Engineering
AE 8/9
Q.46 Consider a 20
0
half-angle wedge in a supersonic flow at Mach 3.0 at standard sea-level
conditions. If the shock-wave angle on the wedge is 36
0
, the Mach number of the tangential
component of the flow post-shock is _______ (accurate to two decimal places).
Q.47 The boundary layer thickness at the location of a sensor on a flat plate in an incompressible,
laminar flow of air is required to be restricted to 1 mm for an effective measurement. If the
flow velocity is 20 m/s with 1 bar pressure, 300 K temperature, and 1.789?10
?5
kg/(m-s)
viscosity, the maximum distance (in mm) of the sensor location from the leading edge is
________ (accurate to one decimal place).
Q.48 Gross weight of an airplane is 7000 N, wing area is 16 m
2
,
and the maximum lift coefficient
is 2.0. Assuming density at the altitude as 1.23 kg/m
3
, the stall speed (in m/s) of the aircraft
is _________ (accurate to two decimal places).
Q.49 A thin-walled tube with external radius of 100 mm and wall thickness of 2 mm, is fixed at
one end. It is subjected to a compressive force of 1 N acting at a point on the circumference
parallel to its length. The maximum normal stress (in kPa) experienced by the structure is
_____________ (accurate to two decimal places).
Q.50 A 1 m long massless cantilever beam oscillates at 2Hz, while a 60 kg mass is attached at the
tip of it. The flexural rigidity of the beam (in kN-m
2
) is _________________ (accurate to
two decimal places).
Q.51 A cantilever beam having a rectangular cross-section of width 60 mm and depth 100 mm, is
made of aluminum alloy. The material mechanical properties are: Young?s modulus,
E = 73 GPa and ultimate stress, ?? ?? = 480 MPa. Assuming a factor of safety of 4, the
maximum bending moment (in kN-m) that can be applied on the beam is _____ (accurate to
one decimal place).
Q.52 The components of stress in a body under plane stress condition, in the absence of body
forces, is given by:
?? ????
= ?? ?? 2
; ?? ????
= 12?? 2
? 6?? 2
and ?? ????
= 12???? .
The coefficient, A, such that the body is under equilibrium is _____ (accurate to one decimal
place).
Q.53 An axial compressor rotor with 50 % degree of reaction, operates with an axial velocity of
200 m/s. The absolute flow angle at the inlet of the rotor is 22
o
with reference to the axial
direction. If the axial velocity is assumed to remain constant through the rotor, the magnitude
of the relative velocity (in m/s) at the rotor exit is __________ (accurate to one decimal
place).
GATE 2018 Aerospace Engineering
AE 9/9
Q.54 The relative velocity of air leaving a straight radial impeller of a centrifugal compressor is
100 m/s. If the impeller tip speed is 200 m/s, for a slip free operation, the absolute velocity
(in m/s) at the impeller exit is _________ (accurate to one decimal place).
Q.55 An aircraft wind tunnel model, having a pitch axis mass moment of inertia (Iyy) of
0.014 kg-m
2
, is mounted in such a manner that it has pure pitching motion about its centre
of gravity, where it is supported through a frictionless hinge. If the pitching moment (M)
derivative with respect to angle of attack (?), denoted by ?M??, is -0.504 N-m/rad and the
pitching moment (M) derivative with respect to pitch rate (q), denoted by ?Mq?, is
-0.0336 N-m/(rad/s), the damping ratio of the resulting motion due to an initial disturbance
in pitch angle is approximately _________ (accurate to three decimal places).
END OF THE QUESTION PAPER
FirstRanker.com - FirstRanker's Choice
This post was last modified on 18 December 2019