Download GATE (Graduate Aptitude Test in Engineering) Last 10 Years 2020, 2019, 2018, 2017, 2016, 2015, 2014, 2013, 2012, 2011 and 2010 PE Petroleum Engineering Question Paper With Solution And Answer Key
GA 1/2
Q. 1 ? Q. 5 carry one mark each.
Q.1 ?Going by the _________ that many hands make light work, the school _______ involved
all the students in the task .?
The words that best fill the blanks in the above sentence are
(A) principle, principal (B) principal, principle
(C) principle, principle (D) principal, principal
Q.2 ?Her _______ should not be confused with miserliness; she is ever willing to assist those in
need. ?
The word that best fills the blank in the above sentence is
(A) cleanliness (B) punctuality (C) frugality (D) greatness
Q.3 Seven machines take 7 minutes to make 7 identical toys. At the same rate, how many
minutes would it take for 100 machines to make 100 toys?
(A) 1 (B) 7 (C) 100 (D) 700
Q.4 A rectangle becomes a square when its length and breadth are reduced by 10 m and 5 m,
respectively. During this process, the rectangle loses 650 m
2
of area. What is the area of the
original rectangle in square meters?
(A) 1125 (B) 2250 (C) 2924 (D) 4500
Q.5 A number consists of two digits. The sum of the digits is 9. If 45 is subtracted from the
number, its digits are interchanged. What is the number?
(A) 63 (B) 72 (C) 81 (D) 90
Q. 6 ? Q. 10 carry two marks each.
Q.6 For integers ?? , ?? and ?? , what would be the minimum and maximum values respectively of
?? + ?? + ?? if log |?? | + log |?? | + log |?? | = 0?
(A) -3 and 3 (B) -1 and 1 (C) -1 and 3 (D) 1 and 3
FirstRanker.com - FirstRanker's Choice
GATE 2018 General Aptitude (GA) Set-1
GA 1/2
Q. 1 ? Q. 5 carry one mark each.
Q.1 ?Going by the _________ that many hands make light work, the school _______ involved
all the students in the task .?
The words that best fill the blanks in the above sentence are
(A) principle, principal (B) principal, principle
(C) principle, principle (D) principal, principal
Q.2 ?Her _______ should not be confused with miserliness; she is ever willing to assist those in
need. ?
The word that best fills the blank in the above sentence is
(A) cleanliness (B) punctuality (C) frugality (D) greatness
Q.3 Seven machines take 7 minutes to make 7 identical toys. At the same rate, how many
minutes would it take for 100 machines to make 100 toys?
(A) 1 (B) 7 (C) 100 (D) 700
Q.4 A rectangle becomes a square when its length and breadth are reduced by 10 m and 5 m,
respectively. During this process, the rectangle loses 650 m
2
of area. What is the area of the
original rectangle in square meters?
(A) 1125 (B) 2250 (C) 2924 (D) 4500
Q.5 A number consists of two digits. The sum of the digits is 9. If 45 is subtracted from the
number, its digits are interchanged. What is the number?
(A) 63 (B) 72 (C) 81 (D) 90
Q. 6 ? Q. 10 carry two marks each.
Q.6 For integers ?? , ?? and ?? , what would be the minimum and maximum values respectively of
?? + ?? + ?? if log |?? | + log |?? | + log |?? | = 0?
(A) -3 and 3 (B) -1 and 1 (C) -1 and 3 (D) 1 and 3
GATE 2018 General Aptitude (GA) Set-1
GA 2/2
Q.7 Given that ?? and ?? are integers and ?? + ?? 2
?? 3
is odd, which one of the following
statements is correct?
(A) ?? and ?? are both odd (B) ?? and ?? are both even
(C) ?? is even and ?? is odd (D) ?? is odd and ?? is even
Q.8 From the time the front of a train enters a platform, it takes 25 seconds for the back of the
train to leave the platform, while travelling at a constant speed of 54 km/h. At the same
speed, it takes 14 seconds to pass a man running at 9 km/h in the same direction as the
train. What is the length of the train and that of the platform in meters, respectively?
(A) 210 and 140 (B) 162.5 and 187.5
(C) 245 and 130 (D) 175 and 200
Q.9 Which of the following functions describe the graph shown in the below figure?
(A) ?? = ||?? | + 1| ? 2 (B) ?? = ||?? | ? 1| ? 1
(C) ?? = ||?? | + 1| ? 1 (D) ?? = ||?? ? 1| ? 1|
Q.10 Consider the following three statements:
(i) Some roses are red.
(ii) All red flowers fade quickly.
(iii) Some roses fade quickly.
Which of the following statements can be logically inferred from the above statements?
(A) If (i) is true and (ii) is false, then (iii) is false.
(B) If (i) is true and (ii) is false, then (iii) is true.
(C) If (i) and (ii) are true, then (iii) is true.
(D) If (i) and (ii) are false, then (iii) is false.
END OF THE QUESTION PAPER
FirstRanker.com - FirstRanker's Choice
GATE 2018 General Aptitude (GA) Set-1
GA 1/2
Q. 1 ? Q. 5 carry one mark each.
Q.1 ?Going by the _________ that many hands make light work, the school _______ involved
all the students in the task .?
The words that best fill the blanks in the above sentence are
(A) principle, principal (B) principal, principle
(C) principle, principle (D) principal, principal
Q.2 ?Her _______ should not be confused with miserliness; she is ever willing to assist those in
need. ?
The word that best fills the blank in the above sentence is
(A) cleanliness (B) punctuality (C) frugality (D) greatness
Q.3 Seven machines take 7 minutes to make 7 identical toys. At the same rate, how many
minutes would it take for 100 machines to make 100 toys?
(A) 1 (B) 7 (C) 100 (D) 700
Q.4 A rectangle becomes a square when its length and breadth are reduced by 10 m and 5 m,
respectively. During this process, the rectangle loses 650 m
2
of area. What is the area of the
original rectangle in square meters?
(A) 1125 (B) 2250 (C) 2924 (D) 4500
Q.5 A number consists of two digits. The sum of the digits is 9. If 45 is subtracted from the
number, its digits are interchanged. What is the number?
(A) 63 (B) 72 (C) 81 (D) 90
Q. 6 ? Q. 10 carry two marks each.
Q.6 For integers ?? , ?? and ?? , what would be the minimum and maximum values respectively of
?? + ?? + ?? if log |?? | + log |?? | + log |?? | = 0?
(A) -3 and 3 (B) -1 and 1 (C) -1 and 3 (D) 1 and 3
GATE 2018 General Aptitude (GA) Set-1
GA 2/2
Q.7 Given that ?? and ?? are integers and ?? + ?? 2
?? 3
is odd, which one of the following
statements is correct?
(A) ?? and ?? are both odd (B) ?? and ?? are both even
(C) ?? is even and ?? is odd (D) ?? is odd and ?? is even
Q.8 From the time the front of a train enters a platform, it takes 25 seconds for the back of the
train to leave the platform, while travelling at a constant speed of 54 km/h. At the same
speed, it takes 14 seconds to pass a man running at 9 km/h in the same direction as the
train. What is the length of the train and that of the platform in meters, respectively?
(A) 210 and 140 (B) 162.5 and 187.5
(C) 245 and 130 (D) 175 and 200
Q.9 Which of the following functions describe the graph shown in the below figure?
(A) ?? = ||?? | + 1| ? 2 (B) ?? = ||?? | ? 1| ? 1
(C) ?? = ||?? | + 1| ? 1 (D) ?? = ||?? ? 1| ? 1|
Q.10 Consider the following three statements:
(i) Some roses are red.
(ii) All red flowers fade quickly.
(iii) Some roses fade quickly.
Which of the following statements can be logically inferred from the above statements?
(A) If (i) is true and (ii) is false, then (iii) is false.
(B) If (i) is true and (ii) is false, then (iii) is true.
(C) If (i) and (ii) are true, then (iii) is true.
(D) If (i) and (ii) are false, then (iii) is false.
END OF THE QUESTION PAPER
GATE 2018 Petroleum Engineering
PE 1/17
Q. 1 ? Q. 25 carry one mark each.
Q.1 The Taylor series expansion of the function,
?? (?? ) =
?1
1+?? ,
around ?? = 0 (up to 4
th
order term) is:
(A) 1 + ?? + ?? 2
+ ?? 3
+ ?? 4
(B) ?1 + ?? ? ?? 2
+ ?? 3
? ?? 4
(C) ?1 ? ?? + ?? 2
? ?? 3
+ ?? 4
(D) ?1 + ?? ? 2?? 2
+ 3?? 3
? 4?? 4
Q.2
The inverse of the matrix [
1 3
1 2
] is,
(A) [
2 3
1 1
] (B) [
?2 1
3 ?1
] (C) [
?2 3
1 ?1
] (D) [
2 ?3
?1 1
]
Q.3 The line integral of a vector function ?? ?
(?? ? ) over a curve C in a simply connected domain D
in space, is defined by:
? ?? ?
(?? ? ). ?? ?? ?
?? = ? (?? 1
???? + ?? 2
???? + ?? 3
???? )
??
The line integral is independent of path in D. ?? 1
, ?? 2
, and ?? 3
are continuous, and have
continuous first partial derivatives in D. ?? ?
is a closed curve in D.
Which one of the following is NOT ALWAYS true in domain D?
(A) ?
?
? ?? ?
= 0
?
(B) ?
?
. ?? ?
= 0
(C) ? ?? ?
(?? ? ). ?? ?? ?
?? ?
= 0
(D) ?? ?
? ?? ?
= 0
?
Q.4 Which one of the following is the integrating factor (IF) for the differential equation,
(cos
2
?? )
????
????
+ ?? = cos?? ?
(A) ?? tan ?? (B) ?? cos ??
(C) ?? ? tan ?? (D) ?? sin ??
FirstRanker.com - FirstRanker's Choice
GATE 2018 General Aptitude (GA) Set-1
GA 1/2
Q. 1 ? Q. 5 carry one mark each.
Q.1 ?Going by the _________ that many hands make light work, the school _______ involved
all the students in the task .?
The words that best fill the blanks in the above sentence are
(A) principle, principal (B) principal, principle
(C) principle, principle (D) principal, principal
Q.2 ?Her _______ should not be confused with miserliness; she is ever willing to assist those in
need. ?
The word that best fills the blank in the above sentence is
(A) cleanliness (B) punctuality (C) frugality (D) greatness
Q.3 Seven machines take 7 minutes to make 7 identical toys. At the same rate, how many
minutes would it take for 100 machines to make 100 toys?
(A) 1 (B) 7 (C) 100 (D) 700
Q.4 A rectangle becomes a square when its length and breadth are reduced by 10 m and 5 m,
respectively. During this process, the rectangle loses 650 m
2
of area. What is the area of the
original rectangle in square meters?
(A) 1125 (B) 2250 (C) 2924 (D) 4500
Q.5 A number consists of two digits. The sum of the digits is 9. If 45 is subtracted from the
number, its digits are interchanged. What is the number?
(A) 63 (B) 72 (C) 81 (D) 90
Q. 6 ? Q. 10 carry two marks each.
Q.6 For integers ?? , ?? and ?? , what would be the minimum and maximum values respectively of
?? + ?? + ?? if log |?? | + log |?? | + log |?? | = 0?
(A) -3 and 3 (B) -1 and 1 (C) -1 and 3 (D) 1 and 3
GATE 2018 General Aptitude (GA) Set-1
GA 2/2
Q.7 Given that ?? and ?? are integers and ?? + ?? 2
?? 3
is odd, which one of the following
statements is correct?
(A) ?? and ?? are both odd (B) ?? and ?? are both even
(C) ?? is even and ?? is odd (D) ?? is odd and ?? is even
Q.8 From the time the front of a train enters a platform, it takes 25 seconds for the back of the
train to leave the platform, while travelling at a constant speed of 54 km/h. At the same
speed, it takes 14 seconds to pass a man running at 9 km/h in the same direction as the
train. What is the length of the train and that of the platform in meters, respectively?
(A) 210 and 140 (B) 162.5 and 187.5
(C) 245 and 130 (D) 175 and 200
Q.9 Which of the following functions describe the graph shown in the below figure?
(A) ?? = ||?? | + 1| ? 2 (B) ?? = ||?? | ? 1| ? 1
(C) ?? = ||?? | + 1| ? 1 (D) ?? = ||?? ? 1| ? 1|
Q.10 Consider the following three statements:
(i) Some roses are red.
(ii) All red flowers fade quickly.
(iii) Some roses fade quickly.
Which of the following statements can be logically inferred from the above statements?
(A) If (i) is true and (ii) is false, then (iii) is false.
(B) If (i) is true and (ii) is false, then (iii) is true.
(C) If (i) and (ii) are true, then (iii) is true.
(D) If (i) and (ii) are false, then (iii) is false.
END OF THE QUESTION PAPER
GATE 2018 Petroleum Engineering
PE 1/17
Q. 1 ? Q. 25 carry one mark each.
Q.1 The Taylor series expansion of the function,
?? (?? ) =
?1
1+?? ,
around ?? = 0 (up to 4
th
order term) is:
(A) 1 + ?? + ?? 2
+ ?? 3
+ ?? 4
(B) ?1 + ?? ? ?? 2
+ ?? 3
? ?? 4
(C) ?1 ? ?? + ?? 2
? ?? 3
+ ?? 4
(D) ?1 + ?? ? 2?? 2
+ 3?? 3
? 4?? 4
Q.2
The inverse of the matrix [
1 3
1 2
] is,
(A) [
2 3
1 1
] (B) [
?2 1
3 ?1
] (C) [
?2 3
1 ?1
] (D) [
2 ?3
?1 1
]
Q.3 The line integral of a vector function ?? ?
(?? ? ) over a curve C in a simply connected domain D
in space, is defined by:
? ?? ?
(?? ? ). ?? ?? ?
?? = ? (?? 1
???? + ?? 2
???? + ?? 3
???? )
??
The line integral is independent of path in D. ?? 1
, ?? 2
, and ?? 3
are continuous, and have
continuous first partial derivatives in D. ?? ?
is a closed curve in D.
Which one of the following is NOT ALWAYS true in domain D?
(A) ?
?
? ?? ?
= 0
?
(B) ?
?
. ?? ?
= 0
(C) ? ?? ?
(?? ? ). ?? ?? ?
?? ?
= 0
(D) ?? ?
? ?? ?
= 0
?
Q.4 Which one of the following is the integrating factor (IF) for the differential equation,
(cos
2
?? )
????
????
+ ?? = cos?? ?
(A) ?? tan ?? (B) ?? cos ??
(C) ?? ? tan ?? (D) ?? sin ??
GATE 2018 Petroleum Engineering
PE 2/17
Q.5 A phase diagram of a black oil is shown in the figure (Y is the critical point).
Match the following:
(P) Curve XY (I) Dew point curve
(Q) Curve YZ (II) Single phase liquid
(R) Phase I (III) Bubble point curve
(S) Phase II (IV) Single phase gas
(A) P-I, Q-III, R-II, S-IV (B) P-III, Q-I, R-II, S-IV
(C) P-III, Q-I, R-IV, S-II (D) P-I, Q-II, R-III, S-IV
Q.6 Match the following chemicals to their respective oilfield applications:
(P) Hydrate inhibitor (I) Formaldehyde
(Q) Well stimulation (II) Xanthan gum
(R) Drilling fluid biocide (III) Methanol
(S) Viscosifier (IV) Hydrochloric acid
(A) P-IV, Q-III, R-II, S-I (B) P-III, Q-I, R-IV, S-II
(C) P-I, Q-III R-IV, S-II (D) P-III, Q-IV, R-I, S-II
FirstRanker.com - FirstRanker's Choice
GATE 2018 General Aptitude (GA) Set-1
GA 1/2
Q. 1 ? Q. 5 carry one mark each.
Q.1 ?Going by the _________ that many hands make light work, the school _______ involved
all the students in the task .?
The words that best fill the blanks in the above sentence are
(A) principle, principal (B) principal, principle
(C) principle, principle (D) principal, principal
Q.2 ?Her _______ should not be confused with miserliness; she is ever willing to assist those in
need. ?
The word that best fills the blank in the above sentence is
(A) cleanliness (B) punctuality (C) frugality (D) greatness
Q.3 Seven machines take 7 minutes to make 7 identical toys. At the same rate, how many
minutes would it take for 100 machines to make 100 toys?
(A) 1 (B) 7 (C) 100 (D) 700
Q.4 A rectangle becomes a square when its length and breadth are reduced by 10 m and 5 m,
respectively. During this process, the rectangle loses 650 m
2
of area. What is the area of the
original rectangle in square meters?
(A) 1125 (B) 2250 (C) 2924 (D) 4500
Q.5 A number consists of two digits. The sum of the digits is 9. If 45 is subtracted from the
number, its digits are interchanged. What is the number?
(A) 63 (B) 72 (C) 81 (D) 90
Q. 6 ? Q. 10 carry two marks each.
Q.6 For integers ?? , ?? and ?? , what would be the minimum and maximum values respectively of
?? + ?? + ?? if log |?? | + log |?? | + log |?? | = 0?
(A) -3 and 3 (B) -1 and 1 (C) -1 and 3 (D) 1 and 3
GATE 2018 General Aptitude (GA) Set-1
GA 2/2
Q.7 Given that ?? and ?? are integers and ?? + ?? 2
?? 3
is odd, which one of the following
statements is correct?
(A) ?? and ?? are both odd (B) ?? and ?? are both even
(C) ?? is even and ?? is odd (D) ?? is odd and ?? is even
Q.8 From the time the front of a train enters a platform, it takes 25 seconds for the back of the
train to leave the platform, while travelling at a constant speed of 54 km/h. At the same
speed, it takes 14 seconds to pass a man running at 9 km/h in the same direction as the
train. What is the length of the train and that of the platform in meters, respectively?
(A) 210 and 140 (B) 162.5 and 187.5
(C) 245 and 130 (D) 175 and 200
Q.9 Which of the following functions describe the graph shown in the below figure?
(A) ?? = ||?? | + 1| ? 2 (B) ?? = ||?? | ? 1| ? 1
(C) ?? = ||?? | + 1| ? 1 (D) ?? = ||?? ? 1| ? 1|
Q.10 Consider the following three statements:
(i) Some roses are red.
(ii) All red flowers fade quickly.
(iii) Some roses fade quickly.
Which of the following statements can be logically inferred from the above statements?
(A) If (i) is true and (ii) is false, then (iii) is false.
(B) If (i) is true and (ii) is false, then (iii) is true.
(C) If (i) and (ii) are true, then (iii) is true.
(D) If (i) and (ii) are false, then (iii) is false.
END OF THE QUESTION PAPER
GATE 2018 Petroleum Engineering
PE 1/17
Q. 1 ? Q. 25 carry one mark each.
Q.1 The Taylor series expansion of the function,
?? (?? ) =
?1
1+?? ,
around ?? = 0 (up to 4
th
order term) is:
(A) 1 + ?? + ?? 2
+ ?? 3
+ ?? 4
(B) ?1 + ?? ? ?? 2
+ ?? 3
? ?? 4
(C) ?1 ? ?? + ?? 2
? ?? 3
+ ?? 4
(D) ?1 + ?? ? 2?? 2
+ 3?? 3
? 4?? 4
Q.2
The inverse of the matrix [
1 3
1 2
] is,
(A) [
2 3
1 1
] (B) [
?2 1
3 ?1
] (C) [
?2 3
1 ?1
] (D) [
2 ?3
?1 1
]
Q.3 The line integral of a vector function ?? ?
(?? ? ) over a curve C in a simply connected domain D
in space, is defined by:
? ?? ?
(?? ? ). ?? ?? ?
?? = ? (?? 1
???? + ?? 2
???? + ?? 3
???? )
??
The line integral is independent of path in D. ?? 1
, ?? 2
, and ?? 3
are continuous, and have
continuous first partial derivatives in D. ?? ?
is a closed curve in D.
Which one of the following is NOT ALWAYS true in domain D?
(A) ?
?
? ?? ?
= 0
?
(B) ?
?
. ?? ?
= 0
(C) ? ?? ?
(?? ? ). ?? ?? ?
?? ?
= 0
(D) ?? ?
? ?? ?
= 0
?
Q.4 Which one of the following is the integrating factor (IF) for the differential equation,
(cos
2
?? )
????
????
+ ?? = cos?? ?
(A) ?? tan ?? (B) ?? cos ??
(C) ?? ? tan ?? (D) ?? sin ??
GATE 2018 Petroleum Engineering
PE 2/17
Q.5 A phase diagram of a black oil is shown in the figure (Y is the critical point).
Match the following:
(P) Curve XY (I) Dew point curve
(Q) Curve YZ (II) Single phase liquid
(R) Phase I (III) Bubble point curve
(S) Phase II (IV) Single phase gas
(A) P-I, Q-III, R-II, S-IV (B) P-III, Q-I, R-II, S-IV
(C) P-III, Q-I, R-IV, S-II (D) P-I, Q-II, R-III, S-IV
Q.6 Match the following chemicals to their respective oilfield applications:
(P) Hydrate inhibitor (I) Formaldehyde
(Q) Well stimulation (II) Xanthan gum
(R) Drilling fluid biocide (III) Methanol
(S) Viscosifier (IV) Hydrochloric acid
(A) P-IV, Q-III, R-II, S-I (B) P-III, Q-I, R-IV, S-II
(C) P-I, Q-III R-IV, S-II (D) P-III, Q-IV, R-I, S-II
GATE 2018 Petroleum Engineering
PE 3/17
Q.7 The CH4-hydrate equilibrium curve (dashed) and CO2-hydrate equilibrium curve (solid) on
a pressure-temperature plane above 0?C are shown in the figure. The two curves divide the
plane in four non-overlapping regions. In which region are CO2-hydrates stable and CH4-
hydrates unstable?
(A) I (B) II (C) III (D) IV
Q.8 Plot of ratio of pressure to gas compressibility factor (P/Z) vs. cumulative gas production
(Gp) for a gas reservoir (represented by solid curve in the figure) was shown to a reservoir
engineering student.
The student made the following statements:
(I) A water aquifer is attached to this gas reservoir.
(II) P/Z vs. Gp curve must always be a straight line for water encroachment in a gas
reservoir.
(III) The ultimate gas recovery is diminished due to water encroachment.
Which of the above statements are TRUE?
(A) Only I and II (B) Only II and III (C) Only I and III (D) I, II, and III
Q.9 Waste water from oil industry consists of oil in free and emulsified forms. The oil in the
free form can be recovered by:
(A) Aerated lagoons
(B) Trickling filters
(C) Gravity separators
(D) Biological oxygen pond
P/Z
G p
FirstRanker.com - FirstRanker's Choice
GATE 2018 General Aptitude (GA) Set-1
GA 1/2
Q. 1 ? Q. 5 carry one mark each.
Q.1 ?Going by the _________ that many hands make light work, the school _______ involved
all the students in the task .?
The words that best fill the blanks in the above sentence are
(A) principle, principal (B) principal, principle
(C) principle, principle (D) principal, principal
Q.2 ?Her _______ should not be confused with miserliness; she is ever willing to assist those in
need. ?
The word that best fills the blank in the above sentence is
(A) cleanliness (B) punctuality (C) frugality (D) greatness
Q.3 Seven machines take 7 minutes to make 7 identical toys. At the same rate, how many
minutes would it take for 100 machines to make 100 toys?
(A) 1 (B) 7 (C) 100 (D) 700
Q.4 A rectangle becomes a square when its length and breadth are reduced by 10 m and 5 m,
respectively. During this process, the rectangle loses 650 m
2
of area. What is the area of the
original rectangle in square meters?
(A) 1125 (B) 2250 (C) 2924 (D) 4500
Q.5 A number consists of two digits. The sum of the digits is 9. If 45 is subtracted from the
number, its digits are interchanged. What is the number?
(A) 63 (B) 72 (C) 81 (D) 90
Q. 6 ? Q. 10 carry two marks each.
Q.6 For integers ?? , ?? and ?? , what would be the minimum and maximum values respectively of
?? + ?? + ?? if log |?? | + log |?? | + log |?? | = 0?
(A) -3 and 3 (B) -1 and 1 (C) -1 and 3 (D) 1 and 3
GATE 2018 General Aptitude (GA) Set-1
GA 2/2
Q.7 Given that ?? and ?? are integers and ?? + ?? 2
?? 3
is odd, which one of the following
statements is correct?
(A) ?? and ?? are both odd (B) ?? and ?? are both even
(C) ?? is even and ?? is odd (D) ?? is odd and ?? is even
Q.8 From the time the front of a train enters a platform, it takes 25 seconds for the back of the
train to leave the platform, while travelling at a constant speed of 54 km/h. At the same
speed, it takes 14 seconds to pass a man running at 9 km/h in the same direction as the
train. What is the length of the train and that of the platform in meters, respectively?
(A) 210 and 140 (B) 162.5 and 187.5
(C) 245 and 130 (D) 175 and 200
Q.9 Which of the following functions describe the graph shown in the below figure?
(A) ?? = ||?? | + 1| ? 2 (B) ?? = ||?? | ? 1| ? 1
(C) ?? = ||?? | + 1| ? 1 (D) ?? = ||?? ? 1| ? 1|
Q.10 Consider the following three statements:
(i) Some roses are red.
(ii) All red flowers fade quickly.
(iii) Some roses fade quickly.
Which of the following statements can be logically inferred from the above statements?
(A) If (i) is true and (ii) is false, then (iii) is false.
(B) If (i) is true and (ii) is false, then (iii) is true.
(C) If (i) and (ii) are true, then (iii) is true.
(D) If (i) and (ii) are false, then (iii) is false.
END OF THE QUESTION PAPER
GATE 2018 Petroleum Engineering
PE 1/17
Q. 1 ? Q. 25 carry one mark each.
Q.1 The Taylor series expansion of the function,
?? (?? ) =
?1
1+?? ,
around ?? = 0 (up to 4
th
order term) is:
(A) 1 + ?? + ?? 2
+ ?? 3
+ ?? 4
(B) ?1 + ?? ? ?? 2
+ ?? 3
? ?? 4
(C) ?1 ? ?? + ?? 2
? ?? 3
+ ?? 4
(D) ?1 + ?? ? 2?? 2
+ 3?? 3
? 4?? 4
Q.2
The inverse of the matrix [
1 3
1 2
] is,
(A) [
2 3
1 1
] (B) [
?2 1
3 ?1
] (C) [
?2 3
1 ?1
] (D) [
2 ?3
?1 1
]
Q.3 The line integral of a vector function ?? ?
(?? ? ) over a curve C in a simply connected domain D
in space, is defined by:
? ?? ?
(?? ? ). ?? ?? ?
?? = ? (?? 1
???? + ?? 2
???? + ?? 3
???? )
??
The line integral is independent of path in D. ?? 1
, ?? 2
, and ?? 3
are continuous, and have
continuous first partial derivatives in D. ?? ?
is a closed curve in D.
Which one of the following is NOT ALWAYS true in domain D?
(A) ?
?
? ?? ?
= 0
?
(B) ?
?
. ?? ?
= 0
(C) ? ?? ?
(?? ? ). ?? ?? ?
?? ?
= 0
(D) ?? ?
? ?? ?
= 0
?
Q.4 Which one of the following is the integrating factor (IF) for the differential equation,
(cos
2
?? )
????
????
+ ?? = cos?? ?
(A) ?? tan ?? (B) ?? cos ??
(C) ?? ? tan ?? (D) ?? sin ??
GATE 2018 Petroleum Engineering
PE 2/17
Q.5 A phase diagram of a black oil is shown in the figure (Y is the critical point).
Match the following:
(P) Curve XY (I) Dew point curve
(Q) Curve YZ (II) Single phase liquid
(R) Phase I (III) Bubble point curve
(S) Phase II (IV) Single phase gas
(A) P-I, Q-III, R-II, S-IV (B) P-III, Q-I, R-II, S-IV
(C) P-III, Q-I, R-IV, S-II (D) P-I, Q-II, R-III, S-IV
Q.6 Match the following chemicals to their respective oilfield applications:
(P) Hydrate inhibitor (I) Formaldehyde
(Q) Well stimulation (II) Xanthan gum
(R) Drilling fluid biocide (III) Methanol
(S) Viscosifier (IV) Hydrochloric acid
(A) P-IV, Q-III, R-II, S-I (B) P-III, Q-I, R-IV, S-II
(C) P-I, Q-III R-IV, S-II (D) P-III, Q-IV, R-I, S-II
GATE 2018 Petroleum Engineering
PE 3/17
Q.7 The CH4-hydrate equilibrium curve (dashed) and CO2-hydrate equilibrium curve (solid) on
a pressure-temperature plane above 0?C are shown in the figure. The two curves divide the
plane in four non-overlapping regions. In which region are CO2-hydrates stable and CH4-
hydrates unstable?
(A) I (B) II (C) III (D) IV
Q.8 Plot of ratio of pressure to gas compressibility factor (P/Z) vs. cumulative gas production
(Gp) for a gas reservoir (represented by solid curve in the figure) was shown to a reservoir
engineering student.
The student made the following statements:
(I) A water aquifer is attached to this gas reservoir.
(II) P/Z vs. Gp curve must always be a straight line for water encroachment in a gas
reservoir.
(III) The ultimate gas recovery is diminished due to water encroachment.
Which of the above statements are TRUE?
(A) Only I and II (B) Only II and III (C) Only I and III (D) I, II, and III
Q.9 Waste water from oil industry consists of oil in free and emulsified forms. The oil in the
free form can be recovered by:
(A) Aerated lagoons
(B) Trickling filters
(C) Gravity separators
(D) Biological oxygen pond
P/Z
G p
GATE 2018 Petroleum Engineering
PE 4/17
Q.10 A reservoir model consisting of two porous matrices M and N, separated by a fracture, is
shown in the figure. The matrices are strongly water-wet and are saturated with oil of
specific gravity 0.8. Water is injected only in the fracture at injection well A. If the
Reynolds number for the flow in the fracture conduit is assumed to be less than unity, which
one of the following force will dominate oil recovery from the porous matrix M during the
water-flood operation?
(A) Capillary force (B) Gravity force
(C) Viscous force (D) Inertial force
Q.11 A fractional flow curve is given for a core for which the irreducible water saturation is 0.2
and the residual oil saturation is 0.3. The initial water saturation in the core is 0.3. If
Welge?s method is applied to find the breakthrough saturation and fraction flow of water at
breakthrough, which point should be used in the figure to draw a tangent line to the
fractional flow curve.
(A) I (B) II (C) III (D) IV
Injection well A Production well B
Matrix M
Matrix N
Fracture
FirstRanker.com - FirstRanker's Choice
GATE 2018 General Aptitude (GA) Set-1
GA 1/2
Q. 1 ? Q. 5 carry one mark each.
Q.1 ?Going by the _________ that many hands make light work, the school _______ involved
all the students in the task .?
The words that best fill the blanks in the above sentence are
(A) principle, principal (B) principal, principle
(C) principle, principle (D) principal, principal
Q.2 ?Her _______ should not be confused with miserliness; she is ever willing to assist those in
need. ?
The word that best fills the blank in the above sentence is
(A) cleanliness (B) punctuality (C) frugality (D) greatness
Q.3 Seven machines take 7 minutes to make 7 identical toys. At the same rate, how many
minutes would it take for 100 machines to make 100 toys?
(A) 1 (B) 7 (C) 100 (D) 700
Q.4 A rectangle becomes a square when its length and breadth are reduced by 10 m and 5 m,
respectively. During this process, the rectangle loses 650 m
2
of area. What is the area of the
original rectangle in square meters?
(A) 1125 (B) 2250 (C) 2924 (D) 4500
Q.5 A number consists of two digits. The sum of the digits is 9. If 45 is subtracted from the
number, its digits are interchanged. What is the number?
(A) 63 (B) 72 (C) 81 (D) 90
Q. 6 ? Q. 10 carry two marks each.
Q.6 For integers ?? , ?? and ?? , what would be the minimum and maximum values respectively of
?? + ?? + ?? if log |?? | + log |?? | + log |?? | = 0?
(A) -3 and 3 (B) -1 and 1 (C) -1 and 3 (D) 1 and 3
GATE 2018 General Aptitude (GA) Set-1
GA 2/2
Q.7 Given that ?? and ?? are integers and ?? + ?? 2
?? 3
is odd, which one of the following
statements is correct?
(A) ?? and ?? are both odd (B) ?? and ?? are both even
(C) ?? is even and ?? is odd (D) ?? is odd and ?? is even
Q.8 From the time the front of a train enters a platform, it takes 25 seconds for the back of the
train to leave the platform, while travelling at a constant speed of 54 km/h. At the same
speed, it takes 14 seconds to pass a man running at 9 km/h in the same direction as the
train. What is the length of the train and that of the platform in meters, respectively?
(A) 210 and 140 (B) 162.5 and 187.5
(C) 245 and 130 (D) 175 and 200
Q.9 Which of the following functions describe the graph shown in the below figure?
(A) ?? = ||?? | + 1| ? 2 (B) ?? = ||?? | ? 1| ? 1
(C) ?? = ||?? | + 1| ? 1 (D) ?? = ||?? ? 1| ? 1|
Q.10 Consider the following three statements:
(i) Some roses are red.
(ii) All red flowers fade quickly.
(iii) Some roses fade quickly.
Which of the following statements can be logically inferred from the above statements?
(A) If (i) is true and (ii) is false, then (iii) is false.
(B) If (i) is true and (ii) is false, then (iii) is true.
(C) If (i) and (ii) are true, then (iii) is true.
(D) If (i) and (ii) are false, then (iii) is false.
END OF THE QUESTION PAPER
GATE 2018 Petroleum Engineering
PE 1/17
Q. 1 ? Q. 25 carry one mark each.
Q.1 The Taylor series expansion of the function,
?? (?? ) =
?1
1+?? ,
around ?? = 0 (up to 4
th
order term) is:
(A) 1 + ?? + ?? 2
+ ?? 3
+ ?? 4
(B) ?1 + ?? ? ?? 2
+ ?? 3
? ?? 4
(C) ?1 ? ?? + ?? 2
? ?? 3
+ ?? 4
(D) ?1 + ?? ? 2?? 2
+ 3?? 3
? 4?? 4
Q.2
The inverse of the matrix [
1 3
1 2
] is,
(A) [
2 3
1 1
] (B) [
?2 1
3 ?1
] (C) [
?2 3
1 ?1
] (D) [
2 ?3
?1 1
]
Q.3 The line integral of a vector function ?? ?
(?? ? ) over a curve C in a simply connected domain D
in space, is defined by:
? ?? ?
(?? ? ). ?? ?? ?
?? = ? (?? 1
???? + ?? 2
???? + ?? 3
???? )
??
The line integral is independent of path in D. ?? 1
, ?? 2
, and ?? 3
are continuous, and have
continuous first partial derivatives in D. ?? ?
is a closed curve in D.
Which one of the following is NOT ALWAYS true in domain D?
(A) ?
?
? ?? ?
= 0
?
(B) ?
?
. ?? ?
= 0
(C) ? ?? ?
(?? ? ). ?? ?? ?
?? ?
= 0
(D) ?? ?
? ?? ?
= 0
?
Q.4 Which one of the following is the integrating factor (IF) for the differential equation,
(cos
2
?? )
????
????
+ ?? = cos?? ?
(A) ?? tan ?? (B) ?? cos ??
(C) ?? ? tan ?? (D) ?? sin ??
GATE 2018 Petroleum Engineering
PE 2/17
Q.5 A phase diagram of a black oil is shown in the figure (Y is the critical point).
Match the following:
(P) Curve XY (I) Dew point curve
(Q) Curve YZ (II) Single phase liquid
(R) Phase I (III) Bubble point curve
(S) Phase II (IV) Single phase gas
(A) P-I, Q-III, R-II, S-IV (B) P-III, Q-I, R-II, S-IV
(C) P-III, Q-I, R-IV, S-II (D) P-I, Q-II, R-III, S-IV
Q.6 Match the following chemicals to their respective oilfield applications:
(P) Hydrate inhibitor (I) Formaldehyde
(Q) Well stimulation (II) Xanthan gum
(R) Drilling fluid biocide (III) Methanol
(S) Viscosifier (IV) Hydrochloric acid
(A) P-IV, Q-III, R-II, S-I (B) P-III, Q-I, R-IV, S-II
(C) P-I, Q-III R-IV, S-II (D) P-III, Q-IV, R-I, S-II
GATE 2018 Petroleum Engineering
PE 3/17
Q.7 The CH4-hydrate equilibrium curve (dashed) and CO2-hydrate equilibrium curve (solid) on
a pressure-temperature plane above 0?C are shown in the figure. The two curves divide the
plane in four non-overlapping regions. In which region are CO2-hydrates stable and CH4-
hydrates unstable?
(A) I (B) II (C) III (D) IV
Q.8 Plot of ratio of pressure to gas compressibility factor (P/Z) vs. cumulative gas production
(Gp) for a gas reservoir (represented by solid curve in the figure) was shown to a reservoir
engineering student.
The student made the following statements:
(I) A water aquifer is attached to this gas reservoir.
(II) P/Z vs. Gp curve must always be a straight line for water encroachment in a gas
reservoir.
(III) The ultimate gas recovery is diminished due to water encroachment.
Which of the above statements are TRUE?
(A) Only I and II (B) Only II and III (C) Only I and III (D) I, II, and III
Q.9 Waste water from oil industry consists of oil in free and emulsified forms. The oil in the
free form can be recovered by:
(A) Aerated lagoons
(B) Trickling filters
(C) Gravity separators
(D) Biological oxygen pond
P/Z
G p
GATE 2018 Petroleum Engineering
PE 4/17
Q.10 A reservoir model consisting of two porous matrices M and N, separated by a fracture, is
shown in the figure. The matrices are strongly water-wet and are saturated with oil of
specific gravity 0.8. Water is injected only in the fracture at injection well A. If the
Reynolds number for the flow in the fracture conduit is assumed to be less than unity, which
one of the following force will dominate oil recovery from the porous matrix M during the
water-flood operation?
(A) Capillary force (B) Gravity force
(C) Viscous force (D) Inertial force
Q.11 A fractional flow curve is given for a core for which the irreducible water saturation is 0.2
and the residual oil saturation is 0.3. The initial water saturation in the core is 0.3. If
Welge?s method is applied to find the breakthrough saturation and fraction flow of water at
breakthrough, which point should be used in the figure to draw a tangent line to the
fractional flow curve.
(A) I (B) II (C) III (D) IV
Injection well A Production well B
Matrix M
Matrix N
Fracture
GATE 2018 Petroleum Engineering
PE 5/17
Q.12 Which one of the following curves represents behavior of oil phase viscosity as a function
of pressure in the reservoir (where, Pb is the bubble point pressure of oil)?
(A) Curve I (B) Curve II (C) Curve III (D) Curve IV
Q.13 Pick out the INCORRECT statement.
(A) Flash point is always lower than fire point.
(B) Pour point of lube oil can be reduced by removing the wax from it.
(C) Fracturing is a well stimulation technique.
(D) Coal bed methane typically contains more than 60% CO2.
Q.14 Which one of the following phenomena encountered during flooding is desirable for
increasing oil recovery from a reservoir?
(A) Viscous fingering (B) Formation damage
(C) Increase in mobility ratio (D) Decrease in capillary pressure
Q.15 CO2 foams are used for enhanced oil recovery due to which of the following reasons?
(I) It can be used for CO2 sequestration
(II) CO2 can exist in the form of a dense fluid at reservoir conditions
(III) CO2 can convert to hydrocarbon at the reservoir temperature and pressure
(IV) Solubility of CO2 in oil is higher compared to gases like N2
(A) Only I, II, and III (B) Only I, II, and IV
(C) Only II, III, and IV (D) Only I, III, and IV
FirstRanker.com - FirstRanker's Choice
GATE 2018 General Aptitude (GA) Set-1
GA 1/2
Q. 1 ? Q. 5 carry one mark each.
Q.1 ?Going by the _________ that many hands make light work, the school _______ involved
all the students in the task .?
The words that best fill the blanks in the above sentence are
(A) principle, principal (B) principal, principle
(C) principle, principle (D) principal, principal
Q.2 ?Her _______ should not be confused with miserliness; she is ever willing to assist those in
need. ?
The word that best fills the blank in the above sentence is
(A) cleanliness (B) punctuality (C) frugality (D) greatness
Q.3 Seven machines take 7 minutes to make 7 identical toys. At the same rate, how many
minutes would it take for 100 machines to make 100 toys?
(A) 1 (B) 7 (C) 100 (D) 700
Q.4 A rectangle becomes a square when its length and breadth are reduced by 10 m and 5 m,
respectively. During this process, the rectangle loses 650 m
2
of area. What is the area of the
original rectangle in square meters?
(A) 1125 (B) 2250 (C) 2924 (D) 4500
Q.5 A number consists of two digits. The sum of the digits is 9. If 45 is subtracted from the
number, its digits are interchanged. What is the number?
(A) 63 (B) 72 (C) 81 (D) 90
Q. 6 ? Q. 10 carry two marks each.
Q.6 For integers ?? , ?? and ?? , what would be the minimum and maximum values respectively of
?? + ?? + ?? if log |?? | + log |?? | + log |?? | = 0?
(A) -3 and 3 (B) -1 and 1 (C) -1 and 3 (D) 1 and 3
GATE 2018 General Aptitude (GA) Set-1
GA 2/2
Q.7 Given that ?? and ?? are integers and ?? + ?? 2
?? 3
is odd, which one of the following
statements is correct?
(A) ?? and ?? are both odd (B) ?? and ?? are both even
(C) ?? is even and ?? is odd (D) ?? is odd and ?? is even
Q.8 From the time the front of a train enters a platform, it takes 25 seconds for the back of the
train to leave the platform, while travelling at a constant speed of 54 km/h. At the same
speed, it takes 14 seconds to pass a man running at 9 km/h in the same direction as the
train. What is the length of the train and that of the platform in meters, respectively?
(A) 210 and 140 (B) 162.5 and 187.5
(C) 245 and 130 (D) 175 and 200
Q.9 Which of the following functions describe the graph shown in the below figure?
(A) ?? = ||?? | + 1| ? 2 (B) ?? = ||?? | ? 1| ? 1
(C) ?? = ||?? | + 1| ? 1 (D) ?? = ||?? ? 1| ? 1|
Q.10 Consider the following three statements:
(i) Some roses are red.
(ii) All red flowers fade quickly.
(iii) Some roses fade quickly.
Which of the following statements can be logically inferred from the above statements?
(A) If (i) is true and (ii) is false, then (iii) is false.
(B) If (i) is true and (ii) is false, then (iii) is true.
(C) If (i) and (ii) are true, then (iii) is true.
(D) If (i) and (ii) are false, then (iii) is false.
END OF THE QUESTION PAPER
GATE 2018 Petroleum Engineering
PE 1/17
Q. 1 ? Q. 25 carry one mark each.
Q.1 The Taylor series expansion of the function,
?? (?? ) =
?1
1+?? ,
around ?? = 0 (up to 4
th
order term) is:
(A) 1 + ?? + ?? 2
+ ?? 3
+ ?? 4
(B) ?1 + ?? ? ?? 2
+ ?? 3
? ?? 4
(C) ?1 ? ?? + ?? 2
? ?? 3
+ ?? 4
(D) ?1 + ?? ? 2?? 2
+ 3?? 3
? 4?? 4
Q.2
The inverse of the matrix [
1 3
1 2
] is,
(A) [
2 3
1 1
] (B) [
?2 1
3 ?1
] (C) [
?2 3
1 ?1
] (D) [
2 ?3
?1 1
]
Q.3 The line integral of a vector function ?? ?
(?? ? ) over a curve C in a simply connected domain D
in space, is defined by:
? ?? ?
(?? ? ). ?? ?? ?
?? = ? (?? 1
???? + ?? 2
???? + ?? 3
???? )
??
The line integral is independent of path in D. ?? 1
, ?? 2
, and ?? 3
are continuous, and have
continuous first partial derivatives in D. ?? ?
is a closed curve in D.
Which one of the following is NOT ALWAYS true in domain D?
(A) ?
?
? ?? ?
= 0
?
(B) ?
?
. ?? ?
= 0
(C) ? ?? ?
(?? ? ). ?? ?? ?
?? ?
= 0
(D) ?? ?
? ?? ?
= 0
?
Q.4 Which one of the following is the integrating factor (IF) for the differential equation,
(cos
2
?? )
????
????
+ ?? = cos?? ?
(A) ?? tan ?? (B) ?? cos ??
(C) ?? ? tan ?? (D) ?? sin ??
GATE 2018 Petroleum Engineering
PE 2/17
Q.5 A phase diagram of a black oil is shown in the figure (Y is the critical point).
Match the following:
(P) Curve XY (I) Dew point curve
(Q) Curve YZ (II) Single phase liquid
(R) Phase I (III) Bubble point curve
(S) Phase II (IV) Single phase gas
(A) P-I, Q-III, R-II, S-IV (B) P-III, Q-I, R-II, S-IV
(C) P-III, Q-I, R-IV, S-II (D) P-I, Q-II, R-III, S-IV
Q.6 Match the following chemicals to their respective oilfield applications:
(P) Hydrate inhibitor (I) Formaldehyde
(Q) Well stimulation (II) Xanthan gum
(R) Drilling fluid biocide (III) Methanol
(S) Viscosifier (IV) Hydrochloric acid
(A) P-IV, Q-III, R-II, S-I (B) P-III, Q-I, R-IV, S-II
(C) P-I, Q-III R-IV, S-II (D) P-III, Q-IV, R-I, S-II
GATE 2018 Petroleum Engineering
PE 3/17
Q.7 The CH4-hydrate equilibrium curve (dashed) and CO2-hydrate equilibrium curve (solid) on
a pressure-temperature plane above 0?C are shown in the figure. The two curves divide the
plane in four non-overlapping regions. In which region are CO2-hydrates stable and CH4-
hydrates unstable?
(A) I (B) II (C) III (D) IV
Q.8 Plot of ratio of pressure to gas compressibility factor (P/Z) vs. cumulative gas production
(Gp) for a gas reservoir (represented by solid curve in the figure) was shown to a reservoir
engineering student.
The student made the following statements:
(I) A water aquifer is attached to this gas reservoir.
(II) P/Z vs. Gp curve must always be a straight line for water encroachment in a gas
reservoir.
(III) The ultimate gas recovery is diminished due to water encroachment.
Which of the above statements are TRUE?
(A) Only I and II (B) Only II and III (C) Only I and III (D) I, II, and III
Q.9 Waste water from oil industry consists of oil in free and emulsified forms. The oil in the
free form can be recovered by:
(A) Aerated lagoons
(B) Trickling filters
(C) Gravity separators
(D) Biological oxygen pond
P/Z
G p
GATE 2018 Petroleum Engineering
PE 4/17
Q.10 A reservoir model consisting of two porous matrices M and N, separated by a fracture, is
shown in the figure. The matrices are strongly water-wet and are saturated with oil of
specific gravity 0.8. Water is injected only in the fracture at injection well A. If the
Reynolds number for the flow in the fracture conduit is assumed to be less than unity, which
one of the following force will dominate oil recovery from the porous matrix M during the
water-flood operation?
(A) Capillary force (B) Gravity force
(C) Viscous force (D) Inertial force
Q.11 A fractional flow curve is given for a core for which the irreducible water saturation is 0.2
and the residual oil saturation is 0.3. The initial water saturation in the core is 0.3. If
Welge?s method is applied to find the breakthrough saturation and fraction flow of water at
breakthrough, which point should be used in the figure to draw a tangent line to the
fractional flow curve.
(A) I (B) II (C) III (D) IV
Injection well A Production well B
Matrix M
Matrix N
Fracture
GATE 2018 Petroleum Engineering
PE 5/17
Q.12 Which one of the following curves represents behavior of oil phase viscosity as a function
of pressure in the reservoir (where, Pb is the bubble point pressure of oil)?
(A) Curve I (B) Curve II (C) Curve III (D) Curve IV
Q.13 Pick out the INCORRECT statement.
(A) Flash point is always lower than fire point.
(B) Pour point of lube oil can be reduced by removing the wax from it.
(C) Fracturing is a well stimulation technique.
(D) Coal bed methane typically contains more than 60% CO2.
Q.14 Which one of the following phenomena encountered during flooding is desirable for
increasing oil recovery from a reservoir?
(A) Viscous fingering (B) Formation damage
(C) Increase in mobility ratio (D) Decrease in capillary pressure
Q.15 CO2 foams are used for enhanced oil recovery due to which of the following reasons?
(I) It can be used for CO2 sequestration
(II) CO2 can exist in the form of a dense fluid at reservoir conditions
(III) CO2 can convert to hydrocarbon at the reservoir temperature and pressure
(IV) Solubility of CO2 in oil is higher compared to gases like N2
(A) Only I, II, and III (B) Only I, II, and IV
(C) Only II, III, and IV (D) Only I, III, and IV
GATE 2018 Petroleum Engineering
PE 6/17
Q.16 Which one of the following is FALSE about a typical offshore deepwater oil spill?
(A) Using boom boats to prevent spilled oil from spreading
(B) Allowing the spill to reach the shore before clearing
(C) Burning of spilled oil
(D) Using a skimmer to collect the oil
Q.17 Which one of these methods is NOT commonly used to deal with the problem of soil
contamination by oil spillage?
(A) Biodegradation
(B) Leaching out the oil
(C) Soil recycling
(D) Using rain water to wash the contaminants
Q.18 The factor on which the selection of an offshore platform for the reservoir does NOT
depend:
(A) Water depth
(B) Reservoir fluid properties
(C) Sea bed conditions
(D) Best case weather forecast
Q.19 Which one of the following options is correct about the effects of steam stimulation in
increasing the oil production rate?
(I) Reduces the oil viscosity
(II) Increases the formation damage
(III) Reduces the interfacial tension
(IV) Increases the oil viscosity
(A) Only I and II
(B) Only II and III
(C) Only III and IV
(D) Only I and III
Q.20 Which one of the following is INCORRECT about oil based drilling muds?
(A) Good rheological properties at higher temperatures (as high as 250
o
C)
(B) Effective against corrosion
(C) Detection of gas kick is difficult
(D) Less inhibitive than water based muds
Q.21 Assume that viscous, gravity, and capillary are the only dominant forces for fluid flow in a
given reservoir, a cone formed around the perforation zone will break into the well, when
(A) capillary forces are more than viscous and gravity forces.
(B) viscous forces are more than gravity forces.
(C) gravity forces are more than capillary forces.
(D) viscous and gravity forces are equal.
FirstRanker.com - FirstRanker's Choice
GATE 2018 General Aptitude (GA) Set-1
GA 1/2
Q. 1 ? Q. 5 carry one mark each.
Q.1 ?Going by the _________ that many hands make light work, the school _______ involved
all the students in the task .?
The words that best fill the blanks in the above sentence are
(A) principle, principal (B) principal, principle
(C) principle, principle (D) principal, principal
Q.2 ?Her _______ should not be confused with miserliness; she is ever willing to assist those in
need. ?
The word that best fills the blank in the above sentence is
(A) cleanliness (B) punctuality (C) frugality (D) greatness
Q.3 Seven machines take 7 minutes to make 7 identical toys. At the same rate, how many
minutes would it take for 100 machines to make 100 toys?
(A) 1 (B) 7 (C) 100 (D) 700
Q.4 A rectangle becomes a square when its length and breadth are reduced by 10 m and 5 m,
respectively. During this process, the rectangle loses 650 m
2
of area. What is the area of the
original rectangle in square meters?
(A) 1125 (B) 2250 (C) 2924 (D) 4500
Q.5 A number consists of two digits. The sum of the digits is 9. If 45 is subtracted from the
number, its digits are interchanged. What is the number?
(A) 63 (B) 72 (C) 81 (D) 90
Q. 6 ? Q. 10 carry two marks each.
Q.6 For integers ?? , ?? and ?? , what would be the minimum and maximum values respectively of
?? + ?? + ?? if log |?? | + log |?? | + log |?? | = 0?
(A) -3 and 3 (B) -1 and 1 (C) -1 and 3 (D) 1 and 3
GATE 2018 General Aptitude (GA) Set-1
GA 2/2
Q.7 Given that ?? and ?? are integers and ?? + ?? 2
?? 3
is odd, which one of the following
statements is correct?
(A) ?? and ?? are both odd (B) ?? and ?? are both even
(C) ?? is even and ?? is odd (D) ?? is odd and ?? is even
Q.8 From the time the front of a train enters a platform, it takes 25 seconds for the back of the
train to leave the platform, while travelling at a constant speed of 54 km/h. At the same
speed, it takes 14 seconds to pass a man running at 9 km/h in the same direction as the
train. What is the length of the train and that of the platform in meters, respectively?
(A) 210 and 140 (B) 162.5 and 187.5
(C) 245 and 130 (D) 175 and 200
Q.9 Which of the following functions describe the graph shown in the below figure?
(A) ?? = ||?? | + 1| ? 2 (B) ?? = ||?? | ? 1| ? 1
(C) ?? = ||?? | + 1| ? 1 (D) ?? = ||?? ? 1| ? 1|
Q.10 Consider the following three statements:
(i) Some roses are red.
(ii) All red flowers fade quickly.
(iii) Some roses fade quickly.
Which of the following statements can be logically inferred from the above statements?
(A) If (i) is true and (ii) is false, then (iii) is false.
(B) If (i) is true and (ii) is false, then (iii) is true.
(C) If (i) and (ii) are true, then (iii) is true.
(D) If (i) and (ii) are false, then (iii) is false.
END OF THE QUESTION PAPER
GATE 2018 Petroleum Engineering
PE 1/17
Q. 1 ? Q. 25 carry one mark each.
Q.1 The Taylor series expansion of the function,
?? (?? ) =
?1
1+?? ,
around ?? = 0 (up to 4
th
order term) is:
(A) 1 + ?? + ?? 2
+ ?? 3
+ ?? 4
(B) ?1 + ?? ? ?? 2
+ ?? 3
? ?? 4
(C) ?1 ? ?? + ?? 2
? ?? 3
+ ?? 4
(D) ?1 + ?? ? 2?? 2
+ 3?? 3
? 4?? 4
Q.2
The inverse of the matrix [
1 3
1 2
] is,
(A) [
2 3
1 1
] (B) [
?2 1
3 ?1
] (C) [
?2 3
1 ?1
] (D) [
2 ?3
?1 1
]
Q.3 The line integral of a vector function ?? ?
(?? ? ) over a curve C in a simply connected domain D
in space, is defined by:
? ?? ?
(?? ? ). ?? ?? ?
?? = ? (?? 1
???? + ?? 2
???? + ?? 3
???? )
??
The line integral is independent of path in D. ?? 1
, ?? 2
, and ?? 3
are continuous, and have
continuous first partial derivatives in D. ?? ?
is a closed curve in D.
Which one of the following is NOT ALWAYS true in domain D?
(A) ?
?
? ?? ?
= 0
?
(B) ?
?
. ?? ?
= 0
(C) ? ?? ?
(?? ? ). ?? ?? ?
?? ?
= 0
(D) ?? ?
? ?? ?
= 0
?
Q.4 Which one of the following is the integrating factor (IF) for the differential equation,
(cos
2
?? )
????
????
+ ?? = cos?? ?
(A) ?? tan ?? (B) ?? cos ??
(C) ?? ? tan ?? (D) ?? sin ??
GATE 2018 Petroleum Engineering
PE 2/17
Q.5 A phase diagram of a black oil is shown in the figure (Y is the critical point).
Match the following:
(P) Curve XY (I) Dew point curve
(Q) Curve YZ (II) Single phase liquid
(R) Phase I (III) Bubble point curve
(S) Phase II (IV) Single phase gas
(A) P-I, Q-III, R-II, S-IV (B) P-III, Q-I, R-II, S-IV
(C) P-III, Q-I, R-IV, S-II (D) P-I, Q-II, R-III, S-IV
Q.6 Match the following chemicals to their respective oilfield applications:
(P) Hydrate inhibitor (I) Formaldehyde
(Q) Well stimulation (II) Xanthan gum
(R) Drilling fluid biocide (III) Methanol
(S) Viscosifier (IV) Hydrochloric acid
(A) P-IV, Q-III, R-II, S-I (B) P-III, Q-I, R-IV, S-II
(C) P-I, Q-III R-IV, S-II (D) P-III, Q-IV, R-I, S-II
GATE 2018 Petroleum Engineering
PE 3/17
Q.7 The CH4-hydrate equilibrium curve (dashed) and CO2-hydrate equilibrium curve (solid) on
a pressure-temperature plane above 0?C are shown in the figure. The two curves divide the
plane in four non-overlapping regions. In which region are CO2-hydrates stable and CH4-
hydrates unstable?
(A) I (B) II (C) III (D) IV
Q.8 Plot of ratio of pressure to gas compressibility factor (P/Z) vs. cumulative gas production
(Gp) for a gas reservoir (represented by solid curve in the figure) was shown to a reservoir
engineering student.
The student made the following statements:
(I) A water aquifer is attached to this gas reservoir.
(II) P/Z vs. Gp curve must always be a straight line for water encroachment in a gas
reservoir.
(III) The ultimate gas recovery is diminished due to water encroachment.
Which of the above statements are TRUE?
(A) Only I and II (B) Only II and III (C) Only I and III (D) I, II, and III
Q.9 Waste water from oil industry consists of oil in free and emulsified forms. The oil in the
free form can be recovered by:
(A) Aerated lagoons
(B) Trickling filters
(C) Gravity separators
(D) Biological oxygen pond
P/Z
G p
GATE 2018 Petroleum Engineering
PE 4/17
Q.10 A reservoir model consisting of two porous matrices M and N, separated by a fracture, is
shown in the figure. The matrices are strongly water-wet and are saturated with oil of
specific gravity 0.8. Water is injected only in the fracture at injection well A. If the
Reynolds number for the flow in the fracture conduit is assumed to be less than unity, which
one of the following force will dominate oil recovery from the porous matrix M during the
water-flood operation?
(A) Capillary force (B) Gravity force
(C) Viscous force (D) Inertial force
Q.11 A fractional flow curve is given for a core for which the irreducible water saturation is 0.2
and the residual oil saturation is 0.3. The initial water saturation in the core is 0.3. If
Welge?s method is applied to find the breakthrough saturation and fraction flow of water at
breakthrough, which point should be used in the figure to draw a tangent line to the
fractional flow curve.
(A) I (B) II (C) III (D) IV
Injection well A Production well B
Matrix M
Matrix N
Fracture
GATE 2018 Petroleum Engineering
PE 5/17
Q.12 Which one of the following curves represents behavior of oil phase viscosity as a function
of pressure in the reservoir (where, Pb is the bubble point pressure of oil)?
(A) Curve I (B) Curve II (C) Curve III (D) Curve IV
Q.13 Pick out the INCORRECT statement.
(A) Flash point is always lower than fire point.
(B) Pour point of lube oil can be reduced by removing the wax from it.
(C) Fracturing is a well stimulation technique.
(D) Coal bed methane typically contains more than 60% CO2.
Q.14 Which one of the following phenomena encountered during flooding is desirable for
increasing oil recovery from a reservoir?
(A) Viscous fingering (B) Formation damage
(C) Increase in mobility ratio (D) Decrease in capillary pressure
Q.15 CO2 foams are used for enhanced oil recovery due to which of the following reasons?
(I) It can be used for CO2 sequestration
(II) CO2 can exist in the form of a dense fluid at reservoir conditions
(III) CO2 can convert to hydrocarbon at the reservoir temperature and pressure
(IV) Solubility of CO2 in oil is higher compared to gases like N2
(A) Only I, II, and III (B) Only I, II, and IV
(C) Only II, III, and IV (D) Only I, III, and IV
GATE 2018 Petroleum Engineering
PE 6/17
Q.16 Which one of the following is FALSE about a typical offshore deepwater oil spill?
(A) Using boom boats to prevent spilled oil from spreading
(B) Allowing the spill to reach the shore before clearing
(C) Burning of spilled oil
(D) Using a skimmer to collect the oil
Q.17 Which one of these methods is NOT commonly used to deal with the problem of soil
contamination by oil spillage?
(A) Biodegradation
(B) Leaching out the oil
(C) Soil recycling
(D) Using rain water to wash the contaminants
Q.18 The factor on which the selection of an offshore platform for the reservoir does NOT
depend:
(A) Water depth
(B) Reservoir fluid properties
(C) Sea bed conditions
(D) Best case weather forecast
Q.19 Which one of the following options is correct about the effects of steam stimulation in
increasing the oil production rate?
(I) Reduces the oil viscosity
(II) Increases the formation damage
(III) Reduces the interfacial tension
(IV) Increases the oil viscosity
(A) Only I and II
(B) Only II and III
(C) Only III and IV
(D) Only I and III
Q.20 Which one of the following is INCORRECT about oil based drilling muds?
(A) Good rheological properties at higher temperatures (as high as 250
o
C)
(B) Effective against corrosion
(C) Detection of gas kick is difficult
(D) Less inhibitive than water based muds
Q.21 Assume that viscous, gravity, and capillary are the only dominant forces for fluid flow in a
given reservoir, a cone formed around the perforation zone will break into the well, when
(A) capillary forces are more than viscous and gravity forces.
(B) viscous forces are more than gravity forces.
(C) gravity forces are more than capillary forces.
(D) viscous and gravity forces are equal.
GATE 2018 Petroleum Engineering
PE 7/17
Q.22
Two complex numbers, ?? ?
and ?? ? are related as follows:
?? ?
=
?? ?
????
where, ?? = ??1 and ?? is a scalar. Given principal argument of ?? ? , Arg (?? ? ) = ?
2?? 3
, the
principal argument of ?? ?
, Arg(?? ?
) =______________. (rounded-off to two decimal places.
Use ?? = 3.14)
Q.23 A cylindrical sandstone core, 7.5 cm long and 3.5 cm diameter has grain density of
3 g/cm
3
. If the mass of the dry core is 200 g, the porosity of the core is __________%.
(rounded-off to two decimal places)
Q.24 In an oil reservoir the current average pressure is below bubble point pressure of the oil.
The current oil production rate is 10
3
m
3
/day and total gas production rate is 10
5
m
3
/day at
STP conditions (25?C and 1 atm). The formation volume factor of the oil is
1.2
m
3
at reservoir pressure
m
3
at STP
and that of gas is 0.01
m
3
at reservoir pressure
m
3
at STP
. The
dissolved gas oil ratio is 10
m
3
of gas at STP
m
3
of oil at STP
of oil.
The gas flow rate at bottom-hole conditions is ______? 10
2
m
3
per day. (rounded-off to
two decimal places)
Q.25 Exponential decline curve is to be used to estimate the oil reserves of a well. The current
oil production rate is 1000 m
3
per day and yearly decline rate is 6% per year. If the
minimum oil flow rate economically sustainable for the well is 1 m
3
per day, the reserves
(economically producible) associated with the well are _____ ? 10
6
m
3
. (rounded-off to
two decimal places. Use 1 year = 365 days)
FirstRanker.com - FirstRanker's Choice
GATE 2018 General Aptitude (GA) Set-1
GA 1/2
Q. 1 ? Q. 5 carry one mark each.
Q.1 ?Going by the _________ that many hands make light work, the school _______ involved
all the students in the task .?
The words that best fill the blanks in the above sentence are
(A) principle, principal (B) principal, principle
(C) principle, principle (D) principal, principal
Q.2 ?Her _______ should not be confused with miserliness; she is ever willing to assist those in
need. ?
The word that best fills the blank in the above sentence is
(A) cleanliness (B) punctuality (C) frugality (D) greatness
Q.3 Seven machines take 7 minutes to make 7 identical toys. At the same rate, how many
minutes would it take for 100 machines to make 100 toys?
(A) 1 (B) 7 (C) 100 (D) 700
Q.4 A rectangle becomes a square when its length and breadth are reduced by 10 m and 5 m,
respectively. During this process, the rectangle loses 650 m
2
of area. What is the area of the
original rectangle in square meters?
(A) 1125 (B) 2250 (C) 2924 (D) 4500
Q.5 A number consists of two digits. The sum of the digits is 9. If 45 is subtracted from the
number, its digits are interchanged. What is the number?
(A) 63 (B) 72 (C) 81 (D) 90
Q. 6 ? Q. 10 carry two marks each.
Q.6 For integers ?? , ?? and ?? , what would be the minimum and maximum values respectively of
?? + ?? + ?? if log |?? | + log |?? | + log |?? | = 0?
(A) -3 and 3 (B) -1 and 1 (C) -1 and 3 (D) 1 and 3
GATE 2018 General Aptitude (GA) Set-1
GA 2/2
Q.7 Given that ?? and ?? are integers and ?? + ?? 2
?? 3
is odd, which one of the following
statements is correct?
(A) ?? and ?? are both odd (B) ?? and ?? are both even
(C) ?? is even and ?? is odd (D) ?? is odd and ?? is even
Q.8 From the time the front of a train enters a platform, it takes 25 seconds for the back of the
train to leave the platform, while travelling at a constant speed of 54 km/h. At the same
speed, it takes 14 seconds to pass a man running at 9 km/h in the same direction as the
train. What is the length of the train and that of the platform in meters, respectively?
(A) 210 and 140 (B) 162.5 and 187.5
(C) 245 and 130 (D) 175 and 200
Q.9 Which of the following functions describe the graph shown in the below figure?
(A) ?? = ||?? | + 1| ? 2 (B) ?? = ||?? | ? 1| ? 1
(C) ?? = ||?? | + 1| ? 1 (D) ?? = ||?? ? 1| ? 1|
Q.10 Consider the following three statements:
(i) Some roses are red.
(ii) All red flowers fade quickly.
(iii) Some roses fade quickly.
Which of the following statements can be logically inferred from the above statements?
(A) If (i) is true and (ii) is false, then (iii) is false.
(B) If (i) is true and (ii) is false, then (iii) is true.
(C) If (i) and (ii) are true, then (iii) is true.
(D) If (i) and (ii) are false, then (iii) is false.
END OF THE QUESTION PAPER
GATE 2018 Petroleum Engineering
PE 1/17
Q. 1 ? Q. 25 carry one mark each.
Q.1 The Taylor series expansion of the function,
?? (?? ) =
?1
1+?? ,
around ?? = 0 (up to 4
th
order term) is:
(A) 1 + ?? + ?? 2
+ ?? 3
+ ?? 4
(B) ?1 + ?? ? ?? 2
+ ?? 3
? ?? 4
(C) ?1 ? ?? + ?? 2
? ?? 3
+ ?? 4
(D) ?1 + ?? ? 2?? 2
+ 3?? 3
? 4?? 4
Q.2
The inverse of the matrix [
1 3
1 2
] is,
(A) [
2 3
1 1
] (B) [
?2 1
3 ?1
] (C) [
?2 3
1 ?1
] (D) [
2 ?3
?1 1
]
Q.3 The line integral of a vector function ?? ?
(?? ? ) over a curve C in a simply connected domain D
in space, is defined by:
? ?? ?
(?? ? ). ?? ?? ?
?? = ? (?? 1
???? + ?? 2
???? + ?? 3
???? )
??
The line integral is independent of path in D. ?? 1
, ?? 2
, and ?? 3
are continuous, and have
continuous first partial derivatives in D. ?? ?
is a closed curve in D.
Which one of the following is NOT ALWAYS true in domain D?
(A) ?
?
? ?? ?
= 0
?
(B) ?
?
. ?? ?
= 0
(C) ? ?? ?
(?? ? ). ?? ?? ?
?? ?
= 0
(D) ?? ?
? ?? ?
= 0
?
Q.4 Which one of the following is the integrating factor (IF) for the differential equation,
(cos
2
?? )
????
????
+ ?? = cos?? ?
(A) ?? tan ?? (B) ?? cos ??
(C) ?? ? tan ?? (D) ?? sin ??
GATE 2018 Petroleum Engineering
PE 2/17
Q.5 A phase diagram of a black oil is shown in the figure (Y is the critical point).
Match the following:
(P) Curve XY (I) Dew point curve
(Q) Curve YZ (II) Single phase liquid
(R) Phase I (III) Bubble point curve
(S) Phase II (IV) Single phase gas
(A) P-I, Q-III, R-II, S-IV (B) P-III, Q-I, R-II, S-IV
(C) P-III, Q-I, R-IV, S-II (D) P-I, Q-II, R-III, S-IV
Q.6 Match the following chemicals to their respective oilfield applications:
(P) Hydrate inhibitor (I) Formaldehyde
(Q) Well stimulation (II) Xanthan gum
(R) Drilling fluid biocide (III) Methanol
(S) Viscosifier (IV) Hydrochloric acid
(A) P-IV, Q-III, R-II, S-I (B) P-III, Q-I, R-IV, S-II
(C) P-I, Q-III R-IV, S-II (D) P-III, Q-IV, R-I, S-II
GATE 2018 Petroleum Engineering
PE 3/17
Q.7 The CH4-hydrate equilibrium curve (dashed) and CO2-hydrate equilibrium curve (solid) on
a pressure-temperature plane above 0?C are shown in the figure. The two curves divide the
plane in four non-overlapping regions. In which region are CO2-hydrates stable and CH4-
hydrates unstable?
(A) I (B) II (C) III (D) IV
Q.8 Plot of ratio of pressure to gas compressibility factor (P/Z) vs. cumulative gas production
(Gp) for a gas reservoir (represented by solid curve in the figure) was shown to a reservoir
engineering student.
The student made the following statements:
(I) A water aquifer is attached to this gas reservoir.
(II) P/Z vs. Gp curve must always be a straight line for water encroachment in a gas
reservoir.
(III) The ultimate gas recovery is diminished due to water encroachment.
Which of the above statements are TRUE?
(A) Only I and II (B) Only II and III (C) Only I and III (D) I, II, and III
Q.9 Waste water from oil industry consists of oil in free and emulsified forms. The oil in the
free form can be recovered by:
(A) Aerated lagoons
(B) Trickling filters
(C) Gravity separators
(D) Biological oxygen pond
P/Z
G p
GATE 2018 Petroleum Engineering
PE 4/17
Q.10 A reservoir model consisting of two porous matrices M and N, separated by a fracture, is
shown in the figure. The matrices are strongly water-wet and are saturated with oil of
specific gravity 0.8. Water is injected only in the fracture at injection well A. If the
Reynolds number for the flow in the fracture conduit is assumed to be less than unity, which
one of the following force will dominate oil recovery from the porous matrix M during the
water-flood operation?
(A) Capillary force (B) Gravity force
(C) Viscous force (D) Inertial force
Q.11 A fractional flow curve is given for a core for which the irreducible water saturation is 0.2
and the residual oil saturation is 0.3. The initial water saturation in the core is 0.3. If
Welge?s method is applied to find the breakthrough saturation and fraction flow of water at
breakthrough, which point should be used in the figure to draw a tangent line to the
fractional flow curve.
(A) I (B) II (C) III (D) IV
Injection well A Production well B
Matrix M
Matrix N
Fracture
GATE 2018 Petroleum Engineering
PE 5/17
Q.12 Which one of the following curves represents behavior of oil phase viscosity as a function
of pressure in the reservoir (where, Pb is the bubble point pressure of oil)?
(A) Curve I (B) Curve II (C) Curve III (D) Curve IV
Q.13 Pick out the INCORRECT statement.
(A) Flash point is always lower than fire point.
(B) Pour point of lube oil can be reduced by removing the wax from it.
(C) Fracturing is a well stimulation technique.
(D) Coal bed methane typically contains more than 60% CO2.
Q.14 Which one of the following phenomena encountered during flooding is desirable for
increasing oil recovery from a reservoir?
(A) Viscous fingering (B) Formation damage
(C) Increase in mobility ratio (D) Decrease in capillary pressure
Q.15 CO2 foams are used for enhanced oil recovery due to which of the following reasons?
(I) It can be used for CO2 sequestration
(II) CO2 can exist in the form of a dense fluid at reservoir conditions
(III) CO2 can convert to hydrocarbon at the reservoir temperature and pressure
(IV) Solubility of CO2 in oil is higher compared to gases like N2
(A) Only I, II, and III (B) Only I, II, and IV
(C) Only II, III, and IV (D) Only I, III, and IV
GATE 2018 Petroleum Engineering
PE 6/17
Q.16 Which one of the following is FALSE about a typical offshore deepwater oil spill?
(A) Using boom boats to prevent spilled oil from spreading
(B) Allowing the spill to reach the shore before clearing
(C) Burning of spilled oil
(D) Using a skimmer to collect the oil
Q.17 Which one of these methods is NOT commonly used to deal with the problem of soil
contamination by oil spillage?
(A) Biodegradation
(B) Leaching out the oil
(C) Soil recycling
(D) Using rain water to wash the contaminants
Q.18 The factor on which the selection of an offshore platform for the reservoir does NOT
depend:
(A) Water depth
(B) Reservoir fluid properties
(C) Sea bed conditions
(D) Best case weather forecast
Q.19 Which one of the following options is correct about the effects of steam stimulation in
increasing the oil production rate?
(I) Reduces the oil viscosity
(II) Increases the formation damage
(III) Reduces the interfacial tension
(IV) Increases the oil viscosity
(A) Only I and II
(B) Only II and III
(C) Only III and IV
(D) Only I and III
Q.20 Which one of the following is INCORRECT about oil based drilling muds?
(A) Good rheological properties at higher temperatures (as high as 250
o
C)
(B) Effective against corrosion
(C) Detection of gas kick is difficult
(D) Less inhibitive than water based muds
Q.21 Assume that viscous, gravity, and capillary are the only dominant forces for fluid flow in a
given reservoir, a cone formed around the perforation zone will break into the well, when
(A) capillary forces are more than viscous and gravity forces.
(B) viscous forces are more than gravity forces.
(C) gravity forces are more than capillary forces.
(D) viscous and gravity forces are equal.
GATE 2018 Petroleum Engineering
PE 7/17
Q.22
Two complex numbers, ?? ?
and ?? ? are related as follows:
?? ?
=
?? ?
????
where, ?? = ??1 and ?? is a scalar. Given principal argument of ?? ? , Arg (?? ? ) = ?
2?? 3
, the
principal argument of ?? ?
, Arg(?? ?
) =______________. (rounded-off to two decimal places.
Use ?? = 3.14)
Q.23 A cylindrical sandstone core, 7.5 cm long and 3.5 cm diameter has grain density of
3 g/cm
3
. If the mass of the dry core is 200 g, the porosity of the core is __________%.
(rounded-off to two decimal places)
Q.24 In an oil reservoir the current average pressure is below bubble point pressure of the oil.
The current oil production rate is 10
3
m
3
/day and total gas production rate is 10
5
m
3
/day at
STP conditions (25?C and 1 atm). The formation volume factor of the oil is
1.2
m
3
at reservoir pressure
m
3
at STP
and that of gas is 0.01
m
3
at reservoir pressure
m
3
at STP
. The
dissolved gas oil ratio is 10
m
3
of gas at STP
m
3
of oil at STP
of oil.
The gas flow rate at bottom-hole conditions is ______? 10
2
m
3
per day. (rounded-off to
two decimal places)
Q.25 Exponential decline curve is to be used to estimate the oil reserves of a well. The current
oil production rate is 1000 m
3
per day and yearly decline rate is 6% per year. If the
minimum oil flow rate economically sustainable for the well is 1 m
3
per day, the reserves
(economically producible) associated with the well are _____ ? 10
6
m
3
. (rounded-off to
two decimal places. Use 1 year = 365 days)
GATE 2018 Petroleum Engineering
PE 8/17
Q. 26 ? Q. 55 carry two marks each.
Q.26 The probability density for three binomial distributions (D1, D2, and D3) is plotted against
number of successful trials in the given figure.
Each of the plotted distributions corresponds to a unique pair of (n, p) values, where, n is
the number of trials and p is the probability of success in a trial. Three sets of (n, p) values
are provided in the table.
Set (n, p)
I (60, 0.3)
II (60, 0.2)
III (24, 0.5)
Pick the correct match between the (n, p) set and the plotted distribution.
(A) Set I ? D1, Set II ? D2, Set III ? D3
(B) Set I ? D3, Set II ? D1, Set III ? D2
(C) Set I ? D2, Set II ? D3, Set III ? D1
(D) Set I ? D2, Set II ? D1, Set III ? D3
Q.27 Which of the following statements are true about Natural Gas Hydrates?
Natural gas hydrates:
(I) are formed under low temperature and high pressure.
(II) can store approximately 160 m
3
of gas per m
3
of hydrate at 25
o
C and 1 atm.
(III) formation is an endothermic process.
(IV) are potential sources of methane.
(A) Only II, III & IV (B) Only I, II & III
(C) Only I, II & IV (D) Only I, III & IV
0
0.05
0.1
0.15
0 10 20 30
Probability density
Number of successful trials
D1
D2
D3
FirstRanker.com - FirstRanker's Choice
GATE 2018 General Aptitude (GA) Set-1
GA 1/2
Q. 1 ? Q. 5 carry one mark each.
Q.1 ?Going by the _________ that many hands make light work, the school _______ involved
all the students in the task .?
The words that best fill the blanks in the above sentence are
(A) principle, principal (B) principal, principle
(C) principle, principle (D) principal, principal
Q.2 ?Her _______ should not be confused with miserliness; she is ever willing to assist those in
need. ?
The word that best fills the blank in the above sentence is
(A) cleanliness (B) punctuality (C) frugality (D) greatness
Q.3 Seven machines take 7 minutes to make 7 identical toys. At the same rate, how many
minutes would it take for 100 machines to make 100 toys?
(A) 1 (B) 7 (C) 100 (D) 700
Q.4 A rectangle becomes a square when its length and breadth are reduced by 10 m and 5 m,
respectively. During this process, the rectangle loses 650 m
2
of area. What is the area of the
original rectangle in square meters?
(A) 1125 (B) 2250 (C) 2924 (D) 4500
Q.5 A number consists of two digits. The sum of the digits is 9. If 45 is subtracted from the
number, its digits are interchanged. What is the number?
(A) 63 (B) 72 (C) 81 (D) 90
Q. 6 ? Q. 10 carry two marks each.
Q.6 For integers ?? , ?? and ?? , what would be the minimum and maximum values respectively of
?? + ?? + ?? if log |?? | + log |?? | + log |?? | = 0?
(A) -3 and 3 (B) -1 and 1 (C) -1 and 3 (D) 1 and 3
GATE 2018 General Aptitude (GA) Set-1
GA 2/2
Q.7 Given that ?? and ?? are integers and ?? + ?? 2
?? 3
is odd, which one of the following
statements is correct?
(A) ?? and ?? are both odd (B) ?? and ?? are both even
(C) ?? is even and ?? is odd (D) ?? is odd and ?? is even
Q.8 From the time the front of a train enters a platform, it takes 25 seconds for the back of the
train to leave the platform, while travelling at a constant speed of 54 km/h. At the same
speed, it takes 14 seconds to pass a man running at 9 km/h in the same direction as the
train. What is the length of the train and that of the platform in meters, respectively?
(A) 210 and 140 (B) 162.5 and 187.5
(C) 245 and 130 (D) 175 and 200
Q.9 Which of the following functions describe the graph shown in the below figure?
(A) ?? = ||?? | + 1| ? 2 (B) ?? = ||?? | ? 1| ? 1
(C) ?? = ||?? | + 1| ? 1 (D) ?? = ||?? ? 1| ? 1|
Q.10 Consider the following three statements:
(i) Some roses are red.
(ii) All red flowers fade quickly.
(iii) Some roses fade quickly.
Which of the following statements can be logically inferred from the above statements?
(A) If (i) is true and (ii) is false, then (iii) is false.
(B) If (i) is true and (ii) is false, then (iii) is true.
(C) If (i) and (ii) are true, then (iii) is true.
(D) If (i) and (ii) are false, then (iii) is false.
END OF THE QUESTION PAPER
GATE 2018 Petroleum Engineering
PE 1/17
Q. 1 ? Q. 25 carry one mark each.
Q.1 The Taylor series expansion of the function,
?? (?? ) =
?1
1+?? ,
around ?? = 0 (up to 4
th
order term) is:
(A) 1 + ?? + ?? 2
+ ?? 3
+ ?? 4
(B) ?1 + ?? ? ?? 2
+ ?? 3
? ?? 4
(C) ?1 ? ?? + ?? 2
? ?? 3
+ ?? 4
(D) ?1 + ?? ? 2?? 2
+ 3?? 3
? 4?? 4
Q.2
The inverse of the matrix [
1 3
1 2
] is,
(A) [
2 3
1 1
] (B) [
?2 1
3 ?1
] (C) [
?2 3
1 ?1
] (D) [
2 ?3
?1 1
]
Q.3 The line integral of a vector function ?? ?
(?? ? ) over a curve C in a simply connected domain D
in space, is defined by:
? ?? ?
(?? ? ). ?? ?? ?
?? = ? (?? 1
???? + ?? 2
???? + ?? 3
???? )
??
The line integral is independent of path in D. ?? 1
, ?? 2
, and ?? 3
are continuous, and have
continuous first partial derivatives in D. ?? ?
is a closed curve in D.
Which one of the following is NOT ALWAYS true in domain D?
(A) ?
?
? ?? ?
= 0
?
(B) ?
?
. ?? ?
= 0
(C) ? ?? ?
(?? ? ). ?? ?? ?
?? ?
= 0
(D) ?? ?
? ?? ?
= 0
?
Q.4 Which one of the following is the integrating factor (IF) for the differential equation,
(cos
2
?? )
????
????
+ ?? = cos?? ?
(A) ?? tan ?? (B) ?? cos ??
(C) ?? ? tan ?? (D) ?? sin ??
GATE 2018 Petroleum Engineering
PE 2/17
Q.5 A phase diagram of a black oil is shown in the figure (Y is the critical point).
Match the following:
(P) Curve XY (I) Dew point curve
(Q) Curve YZ (II) Single phase liquid
(R) Phase I (III) Bubble point curve
(S) Phase II (IV) Single phase gas
(A) P-I, Q-III, R-II, S-IV (B) P-III, Q-I, R-II, S-IV
(C) P-III, Q-I, R-IV, S-II (D) P-I, Q-II, R-III, S-IV
Q.6 Match the following chemicals to their respective oilfield applications:
(P) Hydrate inhibitor (I) Formaldehyde
(Q) Well stimulation (II) Xanthan gum
(R) Drilling fluid biocide (III) Methanol
(S) Viscosifier (IV) Hydrochloric acid
(A) P-IV, Q-III, R-II, S-I (B) P-III, Q-I, R-IV, S-II
(C) P-I, Q-III R-IV, S-II (D) P-III, Q-IV, R-I, S-II
GATE 2018 Petroleum Engineering
PE 3/17
Q.7 The CH4-hydrate equilibrium curve (dashed) and CO2-hydrate equilibrium curve (solid) on
a pressure-temperature plane above 0?C are shown in the figure. The two curves divide the
plane in four non-overlapping regions. In which region are CO2-hydrates stable and CH4-
hydrates unstable?
(A) I (B) II (C) III (D) IV
Q.8 Plot of ratio of pressure to gas compressibility factor (P/Z) vs. cumulative gas production
(Gp) for a gas reservoir (represented by solid curve in the figure) was shown to a reservoir
engineering student.
The student made the following statements:
(I) A water aquifer is attached to this gas reservoir.
(II) P/Z vs. Gp curve must always be a straight line for water encroachment in a gas
reservoir.
(III) The ultimate gas recovery is diminished due to water encroachment.
Which of the above statements are TRUE?
(A) Only I and II (B) Only II and III (C) Only I and III (D) I, II, and III
Q.9 Waste water from oil industry consists of oil in free and emulsified forms. The oil in the
free form can be recovered by:
(A) Aerated lagoons
(B) Trickling filters
(C) Gravity separators
(D) Biological oxygen pond
P/Z
G p
GATE 2018 Petroleum Engineering
PE 4/17
Q.10 A reservoir model consisting of two porous matrices M and N, separated by a fracture, is
shown in the figure. The matrices are strongly water-wet and are saturated with oil of
specific gravity 0.8. Water is injected only in the fracture at injection well A. If the
Reynolds number for the flow in the fracture conduit is assumed to be less than unity, which
one of the following force will dominate oil recovery from the porous matrix M during the
water-flood operation?
(A) Capillary force (B) Gravity force
(C) Viscous force (D) Inertial force
Q.11 A fractional flow curve is given for a core for which the irreducible water saturation is 0.2
and the residual oil saturation is 0.3. The initial water saturation in the core is 0.3. If
Welge?s method is applied to find the breakthrough saturation and fraction flow of water at
breakthrough, which point should be used in the figure to draw a tangent line to the
fractional flow curve.
(A) I (B) II (C) III (D) IV
Injection well A Production well B
Matrix M
Matrix N
Fracture
GATE 2018 Petroleum Engineering
PE 5/17
Q.12 Which one of the following curves represents behavior of oil phase viscosity as a function
of pressure in the reservoir (where, Pb is the bubble point pressure of oil)?
(A) Curve I (B) Curve II (C) Curve III (D) Curve IV
Q.13 Pick out the INCORRECT statement.
(A) Flash point is always lower than fire point.
(B) Pour point of lube oil can be reduced by removing the wax from it.
(C) Fracturing is a well stimulation technique.
(D) Coal bed methane typically contains more than 60% CO2.
Q.14 Which one of the following phenomena encountered during flooding is desirable for
increasing oil recovery from a reservoir?
(A) Viscous fingering (B) Formation damage
(C) Increase in mobility ratio (D) Decrease in capillary pressure
Q.15 CO2 foams are used for enhanced oil recovery due to which of the following reasons?
(I) It can be used for CO2 sequestration
(II) CO2 can exist in the form of a dense fluid at reservoir conditions
(III) CO2 can convert to hydrocarbon at the reservoir temperature and pressure
(IV) Solubility of CO2 in oil is higher compared to gases like N2
(A) Only I, II, and III (B) Only I, II, and IV
(C) Only II, III, and IV (D) Only I, III, and IV
GATE 2018 Petroleum Engineering
PE 6/17
Q.16 Which one of the following is FALSE about a typical offshore deepwater oil spill?
(A) Using boom boats to prevent spilled oil from spreading
(B) Allowing the spill to reach the shore before clearing
(C) Burning of spilled oil
(D) Using a skimmer to collect the oil
Q.17 Which one of these methods is NOT commonly used to deal with the problem of soil
contamination by oil spillage?
(A) Biodegradation
(B) Leaching out the oil
(C) Soil recycling
(D) Using rain water to wash the contaminants
Q.18 The factor on which the selection of an offshore platform for the reservoir does NOT
depend:
(A) Water depth
(B) Reservoir fluid properties
(C) Sea bed conditions
(D) Best case weather forecast
Q.19 Which one of the following options is correct about the effects of steam stimulation in
increasing the oil production rate?
(I) Reduces the oil viscosity
(II) Increases the formation damage
(III) Reduces the interfacial tension
(IV) Increases the oil viscosity
(A) Only I and II
(B) Only II and III
(C) Only III and IV
(D) Only I and III
Q.20 Which one of the following is INCORRECT about oil based drilling muds?
(A) Good rheological properties at higher temperatures (as high as 250
o
C)
(B) Effective against corrosion
(C) Detection of gas kick is difficult
(D) Less inhibitive than water based muds
Q.21 Assume that viscous, gravity, and capillary are the only dominant forces for fluid flow in a
given reservoir, a cone formed around the perforation zone will break into the well, when
(A) capillary forces are more than viscous and gravity forces.
(B) viscous forces are more than gravity forces.
(C) gravity forces are more than capillary forces.
(D) viscous and gravity forces are equal.
GATE 2018 Petroleum Engineering
PE 7/17
Q.22
Two complex numbers, ?? ?
and ?? ? are related as follows:
?? ?
=
?? ?
????
where, ?? = ??1 and ?? is a scalar. Given principal argument of ?? ? , Arg (?? ? ) = ?
2?? 3
, the
principal argument of ?? ?
, Arg(?? ?
) =______________. (rounded-off to two decimal places.
Use ?? = 3.14)
Q.23 A cylindrical sandstone core, 7.5 cm long and 3.5 cm diameter has grain density of
3 g/cm
3
. If the mass of the dry core is 200 g, the porosity of the core is __________%.
(rounded-off to two decimal places)
Q.24 In an oil reservoir the current average pressure is below bubble point pressure of the oil.
The current oil production rate is 10
3
m
3
/day and total gas production rate is 10
5
m
3
/day at
STP conditions (25?C and 1 atm). The formation volume factor of the oil is
1.2
m
3
at reservoir pressure
m
3
at STP
and that of gas is 0.01
m
3
at reservoir pressure
m
3
at STP
. The
dissolved gas oil ratio is 10
m
3
of gas at STP
m
3
of oil at STP
of oil.
The gas flow rate at bottom-hole conditions is ______? 10
2
m
3
per day. (rounded-off to
two decimal places)
Q.25 Exponential decline curve is to be used to estimate the oil reserves of a well. The current
oil production rate is 1000 m
3
per day and yearly decline rate is 6% per year. If the
minimum oil flow rate economically sustainable for the well is 1 m
3
per day, the reserves
(economically producible) associated with the well are _____ ? 10
6
m
3
. (rounded-off to
two decimal places. Use 1 year = 365 days)
GATE 2018 Petroleum Engineering
PE 8/17
Q. 26 ? Q. 55 carry two marks each.
Q.26 The probability density for three binomial distributions (D1, D2, and D3) is plotted against
number of successful trials in the given figure.
Each of the plotted distributions corresponds to a unique pair of (n, p) values, where, n is
the number of trials and p is the probability of success in a trial. Three sets of (n, p) values
are provided in the table.
Set (n, p)
I (60, 0.3)
II (60, 0.2)
III (24, 0.5)
Pick the correct match between the (n, p) set and the plotted distribution.
(A) Set I ? D1, Set II ? D2, Set III ? D3
(B) Set I ? D3, Set II ? D1, Set III ? D2
(C) Set I ? D2, Set II ? D3, Set III ? D1
(D) Set I ? D2, Set II ? D1, Set III ? D3
Q.27 Which of the following statements are true about Natural Gas Hydrates?
Natural gas hydrates:
(I) are formed under low temperature and high pressure.
(II) can store approximately 160 m
3
of gas per m
3
of hydrate at 25
o
C and 1 atm.
(III) formation is an endothermic process.
(IV) are potential sources of methane.
(A) Only II, III & IV (B) Only I, II & III
(C) Only I, II & IV (D) Only I, III & IV
0
0.05
0.1
0.15
0 10 20 30
Probability density
Number of successful trials
D1
D2
D3
GATE 2018 Petroleum Engineering
PE 9/17
Q.28 P wf (bottom-hole well flowing pressure) vs. Q (flow rate) plots show the inflow
performance relation (IPR) and vertical lift performance (VLP) curves. Figure I shows
VLP curves for two well head pressures Phw1 and Phw2. Figure II shows VLP curves for two
well diameters D1 and D2. Which one of the following statements is true?
(A) Phw1 > Phw2 and D1 < D2 (B) Phw1 > Phw2 and D1 > D2
(C) Phw1 < Phw2 and D1 < D2 (D) Phw1 < Phw2 and D1 > D2
Q.29 Match the following:
(P) Weber Number (I) Ratio of inertial force to viscous force
(Q) Froude Number (II) Ratio of convective heat transfer to conductive heat
transfer
(R) Reynolds number (III) Ratio of inertial force to interfacial force
(S) Nusselt number (IV) Ratio of inertial force to gravitational force
(A) P-III, Q-IV, R-I, S-II (B) P-III, Q-II, R-I, S-IV
(C) P-II, Q-III, R-IV, S-I (D) P-IV, Q-III, R-I, S-II
Q.30 A dilute mixture of coal and sand particles, both of diameter 100 ?m and densities
1800 kg/m
3
and 2600 kg/m
3
, respectively, is to be classified by elutriation technique using
water (density 1000 kg/m
3
, viscosity 10
-3
Pa.s). Assuming Stokes law is applicable, the
minimum settling velocity of the particles in the mixture is (g = 9.81 m/s
2
):
(A) 4.36 ? 10
-3
m/s (B) 8.72 ? 10
-3
m/s
(C) 2.18 ? 10
-3
m/s (D) 1.29 ? 10
-3
m/s
FirstRanker.com - FirstRanker's Choice
GATE 2018 General Aptitude (GA) Set-1
GA 1/2
Q. 1 ? Q. 5 carry one mark each.
Q.1 ?Going by the _________ that many hands make light work, the school _______ involved
all the students in the task .?
The words that best fill the blanks in the above sentence are
(A) principle, principal (B) principal, principle
(C) principle, principle (D) principal, principal
Q.2 ?Her _______ should not be confused with miserliness; she is ever willing to assist those in
need. ?
The word that best fills the blank in the above sentence is
(A) cleanliness (B) punctuality (C) frugality (D) greatness
Q.3 Seven machines take 7 minutes to make 7 identical toys. At the same rate, how many
minutes would it take for 100 machines to make 100 toys?
(A) 1 (B) 7 (C) 100 (D) 700
Q.4 A rectangle becomes a square when its length and breadth are reduced by 10 m and 5 m,
respectively. During this process, the rectangle loses 650 m
2
of area. What is the area of the
original rectangle in square meters?
(A) 1125 (B) 2250 (C) 2924 (D) 4500
Q.5 A number consists of two digits. The sum of the digits is 9. If 45 is subtracted from the
number, its digits are interchanged. What is the number?
(A) 63 (B) 72 (C) 81 (D) 90
Q. 6 ? Q. 10 carry two marks each.
Q.6 For integers ?? , ?? and ?? , what would be the minimum and maximum values respectively of
?? + ?? + ?? if log |?? | + log |?? | + log |?? | = 0?
(A) -3 and 3 (B) -1 and 1 (C) -1 and 3 (D) 1 and 3
GATE 2018 General Aptitude (GA) Set-1
GA 2/2
Q.7 Given that ?? and ?? are integers and ?? + ?? 2
?? 3
is odd, which one of the following
statements is correct?
(A) ?? and ?? are both odd (B) ?? and ?? are both even
(C) ?? is even and ?? is odd (D) ?? is odd and ?? is even
Q.8 From the time the front of a train enters a platform, it takes 25 seconds for the back of the
train to leave the platform, while travelling at a constant speed of 54 km/h. At the same
speed, it takes 14 seconds to pass a man running at 9 km/h in the same direction as the
train. What is the length of the train and that of the platform in meters, respectively?
(A) 210 and 140 (B) 162.5 and 187.5
(C) 245 and 130 (D) 175 and 200
Q.9 Which of the following functions describe the graph shown in the below figure?
(A) ?? = ||?? | + 1| ? 2 (B) ?? = ||?? | ? 1| ? 1
(C) ?? = ||?? | + 1| ? 1 (D) ?? = ||?? ? 1| ? 1|
Q.10 Consider the following three statements:
(i) Some roses are red.
(ii) All red flowers fade quickly.
(iii) Some roses fade quickly.
Which of the following statements can be logically inferred from the above statements?
(A) If (i) is true and (ii) is false, then (iii) is false.
(B) If (i) is true and (ii) is false, then (iii) is true.
(C) If (i) and (ii) are true, then (iii) is true.
(D) If (i) and (ii) are false, then (iii) is false.
END OF THE QUESTION PAPER
GATE 2018 Petroleum Engineering
PE 1/17
Q. 1 ? Q. 25 carry one mark each.
Q.1 The Taylor series expansion of the function,
?? (?? ) =
?1
1+?? ,
around ?? = 0 (up to 4
th
order term) is:
(A) 1 + ?? + ?? 2
+ ?? 3
+ ?? 4
(B) ?1 + ?? ? ?? 2
+ ?? 3
? ?? 4
(C) ?1 ? ?? + ?? 2
? ?? 3
+ ?? 4
(D) ?1 + ?? ? 2?? 2
+ 3?? 3
? 4?? 4
Q.2
The inverse of the matrix [
1 3
1 2
] is,
(A) [
2 3
1 1
] (B) [
?2 1
3 ?1
] (C) [
?2 3
1 ?1
] (D) [
2 ?3
?1 1
]
Q.3 The line integral of a vector function ?? ?
(?? ? ) over a curve C in a simply connected domain D
in space, is defined by:
? ?? ?
(?? ? ). ?? ?? ?
?? = ? (?? 1
???? + ?? 2
???? + ?? 3
???? )
??
The line integral is independent of path in D. ?? 1
, ?? 2
, and ?? 3
are continuous, and have
continuous first partial derivatives in D. ?? ?
is a closed curve in D.
Which one of the following is NOT ALWAYS true in domain D?
(A) ?
?
? ?? ?
= 0
?
(B) ?
?
. ?? ?
= 0
(C) ? ?? ?
(?? ? ). ?? ?? ?
?? ?
= 0
(D) ?? ?
? ?? ?
= 0
?
Q.4 Which one of the following is the integrating factor (IF) for the differential equation,
(cos
2
?? )
????
????
+ ?? = cos?? ?
(A) ?? tan ?? (B) ?? cos ??
(C) ?? ? tan ?? (D) ?? sin ??
GATE 2018 Petroleum Engineering
PE 2/17
Q.5 A phase diagram of a black oil is shown in the figure (Y is the critical point).
Match the following:
(P) Curve XY (I) Dew point curve
(Q) Curve YZ (II) Single phase liquid
(R) Phase I (III) Bubble point curve
(S) Phase II (IV) Single phase gas
(A) P-I, Q-III, R-II, S-IV (B) P-III, Q-I, R-II, S-IV
(C) P-III, Q-I, R-IV, S-II (D) P-I, Q-II, R-III, S-IV
Q.6 Match the following chemicals to their respective oilfield applications:
(P) Hydrate inhibitor (I) Formaldehyde
(Q) Well stimulation (II) Xanthan gum
(R) Drilling fluid biocide (III) Methanol
(S) Viscosifier (IV) Hydrochloric acid
(A) P-IV, Q-III, R-II, S-I (B) P-III, Q-I, R-IV, S-II
(C) P-I, Q-III R-IV, S-II (D) P-III, Q-IV, R-I, S-II
GATE 2018 Petroleum Engineering
PE 3/17
Q.7 The CH4-hydrate equilibrium curve (dashed) and CO2-hydrate equilibrium curve (solid) on
a pressure-temperature plane above 0?C are shown in the figure. The two curves divide the
plane in four non-overlapping regions. In which region are CO2-hydrates stable and CH4-
hydrates unstable?
(A) I (B) II (C) III (D) IV
Q.8 Plot of ratio of pressure to gas compressibility factor (P/Z) vs. cumulative gas production
(Gp) for a gas reservoir (represented by solid curve in the figure) was shown to a reservoir
engineering student.
The student made the following statements:
(I) A water aquifer is attached to this gas reservoir.
(II) P/Z vs. Gp curve must always be a straight line for water encroachment in a gas
reservoir.
(III) The ultimate gas recovery is diminished due to water encroachment.
Which of the above statements are TRUE?
(A) Only I and II (B) Only II and III (C) Only I and III (D) I, II, and III
Q.9 Waste water from oil industry consists of oil in free and emulsified forms. The oil in the
free form can be recovered by:
(A) Aerated lagoons
(B) Trickling filters
(C) Gravity separators
(D) Biological oxygen pond
P/Z
G p
GATE 2018 Petroleum Engineering
PE 4/17
Q.10 A reservoir model consisting of two porous matrices M and N, separated by a fracture, is
shown in the figure. The matrices are strongly water-wet and are saturated with oil of
specific gravity 0.8. Water is injected only in the fracture at injection well A. If the
Reynolds number for the flow in the fracture conduit is assumed to be less than unity, which
one of the following force will dominate oil recovery from the porous matrix M during the
water-flood operation?
(A) Capillary force (B) Gravity force
(C) Viscous force (D) Inertial force
Q.11 A fractional flow curve is given for a core for which the irreducible water saturation is 0.2
and the residual oil saturation is 0.3. The initial water saturation in the core is 0.3. If
Welge?s method is applied to find the breakthrough saturation and fraction flow of water at
breakthrough, which point should be used in the figure to draw a tangent line to the
fractional flow curve.
(A) I (B) II (C) III (D) IV
Injection well A Production well B
Matrix M
Matrix N
Fracture
GATE 2018 Petroleum Engineering
PE 5/17
Q.12 Which one of the following curves represents behavior of oil phase viscosity as a function
of pressure in the reservoir (where, Pb is the bubble point pressure of oil)?
(A) Curve I (B) Curve II (C) Curve III (D) Curve IV
Q.13 Pick out the INCORRECT statement.
(A) Flash point is always lower than fire point.
(B) Pour point of lube oil can be reduced by removing the wax from it.
(C) Fracturing is a well stimulation technique.
(D) Coal bed methane typically contains more than 60% CO2.
Q.14 Which one of the following phenomena encountered during flooding is desirable for
increasing oil recovery from a reservoir?
(A) Viscous fingering (B) Formation damage
(C) Increase in mobility ratio (D) Decrease in capillary pressure
Q.15 CO2 foams are used for enhanced oil recovery due to which of the following reasons?
(I) It can be used for CO2 sequestration
(II) CO2 can exist in the form of a dense fluid at reservoir conditions
(III) CO2 can convert to hydrocarbon at the reservoir temperature and pressure
(IV) Solubility of CO2 in oil is higher compared to gases like N2
(A) Only I, II, and III (B) Only I, II, and IV
(C) Only II, III, and IV (D) Only I, III, and IV
GATE 2018 Petroleum Engineering
PE 6/17
Q.16 Which one of the following is FALSE about a typical offshore deepwater oil spill?
(A) Using boom boats to prevent spilled oil from spreading
(B) Allowing the spill to reach the shore before clearing
(C) Burning of spilled oil
(D) Using a skimmer to collect the oil
Q.17 Which one of these methods is NOT commonly used to deal with the problem of soil
contamination by oil spillage?
(A) Biodegradation
(B) Leaching out the oil
(C) Soil recycling
(D) Using rain water to wash the contaminants
Q.18 The factor on which the selection of an offshore platform for the reservoir does NOT
depend:
(A) Water depth
(B) Reservoir fluid properties
(C) Sea bed conditions
(D) Best case weather forecast
Q.19 Which one of the following options is correct about the effects of steam stimulation in
increasing the oil production rate?
(I) Reduces the oil viscosity
(II) Increases the formation damage
(III) Reduces the interfacial tension
(IV) Increases the oil viscosity
(A) Only I and II
(B) Only II and III
(C) Only III and IV
(D) Only I and III
Q.20 Which one of the following is INCORRECT about oil based drilling muds?
(A) Good rheological properties at higher temperatures (as high as 250
o
C)
(B) Effective against corrosion
(C) Detection of gas kick is difficult
(D) Less inhibitive than water based muds
Q.21 Assume that viscous, gravity, and capillary are the only dominant forces for fluid flow in a
given reservoir, a cone formed around the perforation zone will break into the well, when
(A) capillary forces are more than viscous and gravity forces.
(B) viscous forces are more than gravity forces.
(C) gravity forces are more than capillary forces.
(D) viscous and gravity forces are equal.
GATE 2018 Petroleum Engineering
PE 7/17
Q.22
Two complex numbers, ?? ?
and ?? ? are related as follows:
?? ?
=
?? ?
????
where, ?? = ??1 and ?? is a scalar. Given principal argument of ?? ? , Arg (?? ? ) = ?
2?? 3
, the
principal argument of ?? ?
, Arg(?? ?
) =______________. (rounded-off to two decimal places.
Use ?? = 3.14)
Q.23 A cylindrical sandstone core, 7.5 cm long and 3.5 cm diameter has grain density of
3 g/cm
3
. If the mass of the dry core is 200 g, the porosity of the core is __________%.
(rounded-off to two decimal places)
Q.24 In an oil reservoir the current average pressure is below bubble point pressure of the oil.
The current oil production rate is 10
3
m
3
/day and total gas production rate is 10
5
m
3
/day at
STP conditions (25?C and 1 atm). The formation volume factor of the oil is
1.2
m
3
at reservoir pressure
m
3
at STP
and that of gas is 0.01
m
3
at reservoir pressure
m
3
at STP
. The
dissolved gas oil ratio is 10
m
3
of gas at STP
m
3
of oil at STP
of oil.
The gas flow rate at bottom-hole conditions is ______? 10
2
m
3
per day. (rounded-off to
two decimal places)
Q.25 Exponential decline curve is to be used to estimate the oil reserves of a well. The current
oil production rate is 1000 m
3
per day and yearly decline rate is 6% per year. If the
minimum oil flow rate economically sustainable for the well is 1 m
3
per day, the reserves
(economically producible) associated with the well are _____ ? 10
6
m
3
. (rounded-off to
two decimal places. Use 1 year = 365 days)
GATE 2018 Petroleum Engineering
PE 8/17
Q. 26 ? Q. 55 carry two marks each.
Q.26 The probability density for three binomial distributions (D1, D2, and D3) is plotted against
number of successful trials in the given figure.
Each of the plotted distributions corresponds to a unique pair of (n, p) values, where, n is
the number of trials and p is the probability of success in a trial. Three sets of (n, p) values
are provided in the table.
Set (n, p)
I (60, 0.3)
II (60, 0.2)
III (24, 0.5)
Pick the correct match between the (n, p) set and the plotted distribution.
(A) Set I ? D1, Set II ? D2, Set III ? D3
(B) Set I ? D3, Set II ? D1, Set III ? D2
(C) Set I ? D2, Set II ? D3, Set III ? D1
(D) Set I ? D2, Set II ? D1, Set III ? D3
Q.27 Which of the following statements are true about Natural Gas Hydrates?
Natural gas hydrates:
(I) are formed under low temperature and high pressure.
(II) can store approximately 160 m
3
of gas per m
3
of hydrate at 25
o
C and 1 atm.
(III) formation is an endothermic process.
(IV) are potential sources of methane.
(A) Only II, III & IV (B) Only I, II & III
(C) Only I, II & IV (D) Only I, III & IV
0
0.05
0.1
0.15
0 10 20 30
Probability density
Number of successful trials
D1
D2
D3
GATE 2018 Petroleum Engineering
PE 9/17
Q.28 P wf (bottom-hole well flowing pressure) vs. Q (flow rate) plots show the inflow
performance relation (IPR) and vertical lift performance (VLP) curves. Figure I shows
VLP curves for two well head pressures Phw1 and Phw2. Figure II shows VLP curves for two
well diameters D1 and D2. Which one of the following statements is true?
(A) Phw1 > Phw2 and D1 < D2 (B) Phw1 > Phw2 and D1 > D2
(C) Phw1 < Phw2 and D1 < D2 (D) Phw1 < Phw2 and D1 > D2
Q.29 Match the following:
(P) Weber Number (I) Ratio of inertial force to viscous force
(Q) Froude Number (II) Ratio of convective heat transfer to conductive heat
transfer
(R) Reynolds number (III) Ratio of inertial force to interfacial force
(S) Nusselt number (IV) Ratio of inertial force to gravitational force
(A) P-III, Q-IV, R-I, S-II (B) P-III, Q-II, R-I, S-IV
(C) P-II, Q-III, R-IV, S-I (D) P-IV, Q-III, R-I, S-II
Q.30 A dilute mixture of coal and sand particles, both of diameter 100 ?m and densities
1800 kg/m
3
and 2600 kg/m
3
, respectively, is to be classified by elutriation technique using
water (density 1000 kg/m
3
, viscosity 10
-3
Pa.s). Assuming Stokes law is applicable, the
minimum settling velocity of the particles in the mixture is (g = 9.81 m/s
2
):
(A) 4.36 ? 10
-3
m/s (B) 8.72 ? 10
-3
m/s
(C) 2.18 ? 10
-3
m/s (D) 1.29 ? 10
-3
m/s
GATE 2018 Petroleum Engineering
PE 10/17
Q.31 Oil flow rate and flowing bottom-hole pressure (FBHP) recorded with time during a multi-
rate well test are shown.
Let k is the reservoir permeability, h is the formation thickness and ? is the viscosity of the
oil. ??? ?? (?? ) is constant-rate dimensionless pressure drop as a function of time. The total
pressure drop till time, t, where t > t1, will be:
(A)
?? 1
?? 2???? ?
??? ?? (?? ) +
(?? 2
??? 1
)?? 2???? ?
??? ?? (?? ? ?? 1
)
(B)
?? 1
?? 2???? ?
??? ?? (?? 1
) +
(?? 2
??? 1
)?? 2???? ?
??? ?? (?? ? ?? 1
)
(C)
?? 1
?? 2???? ?
??? ?? (?? ) +
?? 2
?? 2???? ?
??? ?? (?? ? ?? 1
)
(D)
?? 1
?? 2???? ?
??? ?? (?? 1
) +
?? 2
?? 2???? ?
??? ?? (?? )
Q.32 Which one of the following options presents the correct combination?
(P) Reservoir limit test (I) Communication between wells
(Q) Modified isochronal test (II) Ideally zero flowing bottom hole pressure
(R) Interference test (III) Extended drawdown test
(S) Absolute open flow potential (IV) Drawdown and build-up test of equal duration
(A) P-II, Q-III, R-I, S-IV (B) P-IV, Q-I, R-III, S-II
(C) P-III, Q-IV, R-I, S-II (D) P-I, Q-III, R-IV, S-II
FirstRanker.com - FirstRanker's Choice
GATE 2018 General Aptitude (GA) Set-1
GA 1/2
Q. 1 ? Q. 5 carry one mark each.
Q.1 ?Going by the _________ that many hands make light work, the school _______ involved
all the students in the task .?
The words that best fill the blanks in the above sentence are
(A) principle, principal (B) principal, principle
(C) principle, principle (D) principal, principal
Q.2 ?Her _______ should not be confused with miserliness; she is ever willing to assist those in
need. ?
The word that best fills the blank in the above sentence is
(A) cleanliness (B) punctuality (C) frugality (D) greatness
Q.3 Seven machines take 7 minutes to make 7 identical toys. At the same rate, how many
minutes would it take for 100 machines to make 100 toys?
(A) 1 (B) 7 (C) 100 (D) 700
Q.4 A rectangle becomes a square when its length and breadth are reduced by 10 m and 5 m,
respectively. During this process, the rectangle loses 650 m
2
of area. What is the area of the
original rectangle in square meters?
(A) 1125 (B) 2250 (C) 2924 (D) 4500
Q.5 A number consists of two digits. The sum of the digits is 9. If 45 is subtracted from the
number, its digits are interchanged. What is the number?
(A) 63 (B) 72 (C) 81 (D) 90
Q. 6 ? Q. 10 carry two marks each.
Q.6 For integers ?? , ?? and ?? , what would be the minimum and maximum values respectively of
?? + ?? + ?? if log |?? | + log |?? | + log |?? | = 0?
(A) -3 and 3 (B) -1 and 1 (C) -1 and 3 (D) 1 and 3
GATE 2018 General Aptitude (GA) Set-1
GA 2/2
Q.7 Given that ?? and ?? are integers and ?? + ?? 2
?? 3
is odd, which one of the following
statements is correct?
(A) ?? and ?? are both odd (B) ?? and ?? are both even
(C) ?? is even and ?? is odd (D) ?? is odd and ?? is even
Q.8 From the time the front of a train enters a platform, it takes 25 seconds for the back of the
train to leave the platform, while travelling at a constant speed of 54 km/h. At the same
speed, it takes 14 seconds to pass a man running at 9 km/h in the same direction as the
train. What is the length of the train and that of the platform in meters, respectively?
(A) 210 and 140 (B) 162.5 and 187.5
(C) 245 and 130 (D) 175 and 200
Q.9 Which of the following functions describe the graph shown in the below figure?
(A) ?? = ||?? | + 1| ? 2 (B) ?? = ||?? | ? 1| ? 1
(C) ?? = ||?? | + 1| ? 1 (D) ?? = ||?? ? 1| ? 1|
Q.10 Consider the following three statements:
(i) Some roses are red.
(ii) All red flowers fade quickly.
(iii) Some roses fade quickly.
Which of the following statements can be logically inferred from the above statements?
(A) If (i) is true and (ii) is false, then (iii) is false.
(B) If (i) is true and (ii) is false, then (iii) is true.
(C) If (i) and (ii) are true, then (iii) is true.
(D) If (i) and (ii) are false, then (iii) is false.
END OF THE QUESTION PAPER
GATE 2018 Petroleum Engineering
PE 1/17
Q. 1 ? Q. 25 carry one mark each.
Q.1 The Taylor series expansion of the function,
?? (?? ) =
?1
1+?? ,
around ?? = 0 (up to 4
th
order term) is:
(A) 1 + ?? + ?? 2
+ ?? 3
+ ?? 4
(B) ?1 + ?? ? ?? 2
+ ?? 3
? ?? 4
(C) ?1 ? ?? + ?? 2
? ?? 3
+ ?? 4
(D) ?1 + ?? ? 2?? 2
+ 3?? 3
? 4?? 4
Q.2
The inverse of the matrix [
1 3
1 2
] is,
(A) [
2 3
1 1
] (B) [
?2 1
3 ?1
] (C) [
?2 3
1 ?1
] (D) [
2 ?3
?1 1
]
Q.3 The line integral of a vector function ?? ?
(?? ? ) over a curve C in a simply connected domain D
in space, is defined by:
? ?? ?
(?? ? ). ?? ?? ?
?? = ? (?? 1
???? + ?? 2
???? + ?? 3
???? )
??
The line integral is independent of path in D. ?? 1
, ?? 2
, and ?? 3
are continuous, and have
continuous first partial derivatives in D. ?? ?
is a closed curve in D.
Which one of the following is NOT ALWAYS true in domain D?
(A) ?
?
? ?? ?
= 0
?
(B) ?
?
. ?? ?
= 0
(C) ? ?? ?
(?? ? ). ?? ?? ?
?? ?
= 0
(D) ?? ?
? ?? ?
= 0
?
Q.4 Which one of the following is the integrating factor (IF) for the differential equation,
(cos
2
?? )
????
????
+ ?? = cos?? ?
(A) ?? tan ?? (B) ?? cos ??
(C) ?? ? tan ?? (D) ?? sin ??
GATE 2018 Petroleum Engineering
PE 2/17
Q.5 A phase diagram of a black oil is shown in the figure (Y is the critical point).
Match the following:
(P) Curve XY (I) Dew point curve
(Q) Curve YZ (II) Single phase liquid
(R) Phase I (III) Bubble point curve
(S) Phase II (IV) Single phase gas
(A) P-I, Q-III, R-II, S-IV (B) P-III, Q-I, R-II, S-IV
(C) P-III, Q-I, R-IV, S-II (D) P-I, Q-II, R-III, S-IV
Q.6 Match the following chemicals to their respective oilfield applications:
(P) Hydrate inhibitor (I) Formaldehyde
(Q) Well stimulation (II) Xanthan gum
(R) Drilling fluid biocide (III) Methanol
(S) Viscosifier (IV) Hydrochloric acid
(A) P-IV, Q-III, R-II, S-I (B) P-III, Q-I, R-IV, S-II
(C) P-I, Q-III R-IV, S-II (D) P-III, Q-IV, R-I, S-II
GATE 2018 Petroleum Engineering
PE 3/17
Q.7 The CH4-hydrate equilibrium curve (dashed) and CO2-hydrate equilibrium curve (solid) on
a pressure-temperature plane above 0?C are shown in the figure. The two curves divide the
plane in four non-overlapping regions. In which region are CO2-hydrates stable and CH4-
hydrates unstable?
(A) I (B) II (C) III (D) IV
Q.8 Plot of ratio of pressure to gas compressibility factor (P/Z) vs. cumulative gas production
(Gp) for a gas reservoir (represented by solid curve in the figure) was shown to a reservoir
engineering student.
The student made the following statements:
(I) A water aquifer is attached to this gas reservoir.
(II) P/Z vs. Gp curve must always be a straight line for water encroachment in a gas
reservoir.
(III) The ultimate gas recovery is diminished due to water encroachment.
Which of the above statements are TRUE?
(A) Only I and II (B) Only II and III (C) Only I and III (D) I, II, and III
Q.9 Waste water from oil industry consists of oil in free and emulsified forms. The oil in the
free form can be recovered by:
(A) Aerated lagoons
(B) Trickling filters
(C) Gravity separators
(D) Biological oxygen pond
P/Z
G p
GATE 2018 Petroleum Engineering
PE 4/17
Q.10 A reservoir model consisting of two porous matrices M and N, separated by a fracture, is
shown in the figure. The matrices are strongly water-wet and are saturated with oil of
specific gravity 0.8. Water is injected only in the fracture at injection well A. If the
Reynolds number for the flow in the fracture conduit is assumed to be less than unity, which
one of the following force will dominate oil recovery from the porous matrix M during the
water-flood operation?
(A) Capillary force (B) Gravity force
(C) Viscous force (D) Inertial force
Q.11 A fractional flow curve is given for a core for which the irreducible water saturation is 0.2
and the residual oil saturation is 0.3. The initial water saturation in the core is 0.3. If
Welge?s method is applied to find the breakthrough saturation and fraction flow of water at
breakthrough, which point should be used in the figure to draw a tangent line to the
fractional flow curve.
(A) I (B) II (C) III (D) IV
Injection well A Production well B
Matrix M
Matrix N
Fracture
GATE 2018 Petroleum Engineering
PE 5/17
Q.12 Which one of the following curves represents behavior of oil phase viscosity as a function
of pressure in the reservoir (where, Pb is the bubble point pressure of oil)?
(A) Curve I (B) Curve II (C) Curve III (D) Curve IV
Q.13 Pick out the INCORRECT statement.
(A) Flash point is always lower than fire point.
(B) Pour point of lube oil can be reduced by removing the wax from it.
(C) Fracturing is a well stimulation technique.
(D) Coal bed methane typically contains more than 60% CO2.
Q.14 Which one of the following phenomena encountered during flooding is desirable for
increasing oil recovery from a reservoir?
(A) Viscous fingering (B) Formation damage
(C) Increase in mobility ratio (D) Decrease in capillary pressure
Q.15 CO2 foams are used for enhanced oil recovery due to which of the following reasons?
(I) It can be used for CO2 sequestration
(II) CO2 can exist in the form of a dense fluid at reservoir conditions
(III) CO2 can convert to hydrocarbon at the reservoir temperature and pressure
(IV) Solubility of CO2 in oil is higher compared to gases like N2
(A) Only I, II, and III (B) Only I, II, and IV
(C) Only II, III, and IV (D) Only I, III, and IV
GATE 2018 Petroleum Engineering
PE 6/17
Q.16 Which one of the following is FALSE about a typical offshore deepwater oil spill?
(A) Using boom boats to prevent spilled oil from spreading
(B) Allowing the spill to reach the shore before clearing
(C) Burning of spilled oil
(D) Using a skimmer to collect the oil
Q.17 Which one of these methods is NOT commonly used to deal with the problem of soil
contamination by oil spillage?
(A) Biodegradation
(B) Leaching out the oil
(C) Soil recycling
(D) Using rain water to wash the contaminants
Q.18 The factor on which the selection of an offshore platform for the reservoir does NOT
depend:
(A) Water depth
(B) Reservoir fluid properties
(C) Sea bed conditions
(D) Best case weather forecast
Q.19 Which one of the following options is correct about the effects of steam stimulation in
increasing the oil production rate?
(I) Reduces the oil viscosity
(II) Increases the formation damage
(III) Reduces the interfacial tension
(IV) Increases the oil viscosity
(A) Only I and II
(B) Only II and III
(C) Only III and IV
(D) Only I and III
Q.20 Which one of the following is INCORRECT about oil based drilling muds?
(A) Good rheological properties at higher temperatures (as high as 250
o
C)
(B) Effective against corrosion
(C) Detection of gas kick is difficult
(D) Less inhibitive than water based muds
Q.21 Assume that viscous, gravity, and capillary are the only dominant forces for fluid flow in a
given reservoir, a cone formed around the perforation zone will break into the well, when
(A) capillary forces are more than viscous and gravity forces.
(B) viscous forces are more than gravity forces.
(C) gravity forces are more than capillary forces.
(D) viscous and gravity forces are equal.
GATE 2018 Petroleum Engineering
PE 7/17
Q.22
Two complex numbers, ?? ?
and ?? ? are related as follows:
?? ?
=
?? ?
????
where, ?? = ??1 and ?? is a scalar. Given principal argument of ?? ? , Arg (?? ? ) = ?
2?? 3
, the
principal argument of ?? ?
, Arg(?? ?
) =______________. (rounded-off to two decimal places.
Use ?? = 3.14)
Q.23 A cylindrical sandstone core, 7.5 cm long and 3.5 cm diameter has grain density of
3 g/cm
3
. If the mass of the dry core is 200 g, the porosity of the core is __________%.
(rounded-off to two decimal places)
Q.24 In an oil reservoir the current average pressure is below bubble point pressure of the oil.
The current oil production rate is 10
3
m
3
/day and total gas production rate is 10
5
m
3
/day at
STP conditions (25?C and 1 atm). The formation volume factor of the oil is
1.2
m
3
at reservoir pressure
m
3
at STP
and that of gas is 0.01
m
3
at reservoir pressure
m
3
at STP
. The
dissolved gas oil ratio is 10
m
3
of gas at STP
m
3
of oil at STP
of oil.
The gas flow rate at bottom-hole conditions is ______? 10
2
m
3
per day. (rounded-off to
two decimal places)
Q.25 Exponential decline curve is to be used to estimate the oil reserves of a well. The current
oil production rate is 1000 m
3
per day and yearly decline rate is 6% per year. If the
minimum oil flow rate economically sustainable for the well is 1 m
3
per day, the reserves
(economically producible) associated with the well are _____ ? 10
6
m
3
. (rounded-off to
two decimal places. Use 1 year = 365 days)
GATE 2018 Petroleum Engineering
PE 8/17
Q. 26 ? Q. 55 carry two marks each.
Q.26 The probability density for three binomial distributions (D1, D2, and D3) is plotted against
number of successful trials in the given figure.
Each of the plotted distributions corresponds to a unique pair of (n, p) values, where, n is
the number of trials and p is the probability of success in a trial. Three sets of (n, p) values
are provided in the table.
Set (n, p)
I (60, 0.3)
II (60, 0.2)
III (24, 0.5)
Pick the correct match between the (n, p) set and the plotted distribution.
(A) Set I ? D1, Set II ? D2, Set III ? D3
(B) Set I ? D3, Set II ? D1, Set III ? D2
(C) Set I ? D2, Set II ? D3, Set III ? D1
(D) Set I ? D2, Set II ? D1, Set III ? D3
Q.27 Which of the following statements are true about Natural Gas Hydrates?
Natural gas hydrates:
(I) are formed under low temperature and high pressure.
(II) can store approximately 160 m
3
of gas per m
3
of hydrate at 25
o
C and 1 atm.
(III) formation is an endothermic process.
(IV) are potential sources of methane.
(A) Only II, III & IV (B) Only I, II & III
(C) Only I, II & IV (D) Only I, III & IV
0
0.05
0.1
0.15
0 10 20 30
Probability density
Number of successful trials
D1
D2
D3
GATE 2018 Petroleum Engineering
PE 9/17
Q.28 P wf (bottom-hole well flowing pressure) vs. Q (flow rate) plots show the inflow
performance relation (IPR) and vertical lift performance (VLP) curves. Figure I shows
VLP curves for two well head pressures Phw1 and Phw2. Figure II shows VLP curves for two
well diameters D1 and D2. Which one of the following statements is true?
(A) Phw1 > Phw2 and D1 < D2 (B) Phw1 > Phw2 and D1 > D2
(C) Phw1 < Phw2 and D1 < D2 (D) Phw1 < Phw2 and D1 > D2
Q.29 Match the following:
(P) Weber Number (I) Ratio of inertial force to viscous force
(Q) Froude Number (II) Ratio of convective heat transfer to conductive heat
transfer
(R) Reynolds number (III) Ratio of inertial force to interfacial force
(S) Nusselt number (IV) Ratio of inertial force to gravitational force
(A) P-III, Q-IV, R-I, S-II (B) P-III, Q-II, R-I, S-IV
(C) P-II, Q-III, R-IV, S-I (D) P-IV, Q-III, R-I, S-II
Q.30 A dilute mixture of coal and sand particles, both of diameter 100 ?m and densities
1800 kg/m
3
and 2600 kg/m
3
, respectively, is to be classified by elutriation technique using
water (density 1000 kg/m
3
, viscosity 10
-3
Pa.s). Assuming Stokes law is applicable, the
minimum settling velocity of the particles in the mixture is (g = 9.81 m/s
2
):
(A) 4.36 ? 10
-3
m/s (B) 8.72 ? 10
-3
m/s
(C) 2.18 ? 10
-3
m/s (D) 1.29 ? 10
-3
m/s
GATE 2018 Petroleum Engineering
PE 10/17
Q.31 Oil flow rate and flowing bottom-hole pressure (FBHP) recorded with time during a multi-
rate well test are shown.
Let k is the reservoir permeability, h is the formation thickness and ? is the viscosity of the
oil. ??? ?? (?? ) is constant-rate dimensionless pressure drop as a function of time. The total
pressure drop till time, t, where t > t1, will be:
(A)
?? 1
?? 2???? ?
??? ?? (?? ) +
(?? 2
??? 1
)?? 2???? ?
??? ?? (?? ? ?? 1
)
(B)
?? 1
?? 2???? ?
??? ?? (?? 1
) +
(?? 2
??? 1
)?? 2???? ?
??? ?? (?? ? ?? 1
)
(C)
?? 1
?? 2???? ?
??? ?? (?? ) +
?? 2
?? 2???? ?
??? ?? (?? ? ?? 1
)
(D)
?? 1
?? 2???? ?
??? ?? (?? 1
) +
?? 2
?? 2???? ?
??? ?? (?? )
Q.32 Which one of the following options presents the correct combination?
(P) Reservoir limit test (I) Communication between wells
(Q) Modified isochronal test (II) Ideally zero flowing bottom hole pressure
(R) Interference test (III) Extended drawdown test
(S) Absolute open flow potential (IV) Drawdown and build-up test of equal duration
(A) P-II, Q-III, R-I, S-IV (B) P-IV, Q-I, R-III, S-II
(C) P-III, Q-IV, R-I, S-II (D) P-I, Q-III, R-IV, S-II
GATE 2018 Petroleum Engineering
PE 11/17
Q.33 Which one of the following options presents the correct combination?
(P) Roller Cone bits (I) Long and widely spaced teeth
(Q) PDC bits (II) Journal (Pin) angle
(R) Soft formation (III) Short and wider teeth
(S) Hard formation (IV) Size of the cutting
(T) Back rake angle (V) 1400
o
C and 6x10
5
psi
(A) P-II, Q-V, R-I, S-III, T-IV
(B) P-III, Q-IV, R-I, S-II, T-V
(C) P-III, Q-II, R-IV, S-I, T-V
(D) P-II, Q-V, R-III, S-I, T-IV
Q.34 Primary and secondary indicators of kick in a well where the indicators are:
1) flow rate increase,
2) gas, oil or water-cut muds,
3) pit volume increase,
4) flowing well with mud pump shut-off,
5) reduction in drill-pipe weight,
6) drilling break.
Which one of the following presents the correct combination?
(A) Primary (1, 3, 5) and Secondary (2, 4, 6)
(B) Primary (1, 2, 3) and Secondary (4, 5, 6)
(C) Primary (1, 2, 4) and Secondary (3, 5, 6)
(D) Primary (1, 3, 4) and Secondary (2, 5, 6)
FirstRanker.com - FirstRanker's Choice
GATE 2018 General Aptitude (GA) Set-1
GA 1/2
Q. 1 ? Q. 5 carry one mark each.
Q.1 ?Going by the _________ that many hands make light work, the school _______ involved
all the students in the task .?
The words that best fill the blanks in the above sentence are
(A) principle, principal (B) principal, principle
(C) principle, principle (D) principal, principal
Q.2 ?Her _______ should not be confused with miserliness; she is ever willing to assist those in
need. ?
The word that best fills the blank in the above sentence is
(A) cleanliness (B) punctuality (C) frugality (D) greatness
Q.3 Seven machines take 7 minutes to make 7 identical toys. At the same rate, how many
minutes would it take for 100 machines to make 100 toys?
(A) 1 (B) 7 (C) 100 (D) 700
Q.4 A rectangle becomes a square when its length and breadth are reduced by 10 m and 5 m,
respectively. During this process, the rectangle loses 650 m
2
of area. What is the area of the
original rectangle in square meters?
(A) 1125 (B) 2250 (C) 2924 (D) 4500
Q.5 A number consists of two digits. The sum of the digits is 9. If 45 is subtracted from the
number, its digits are interchanged. What is the number?
(A) 63 (B) 72 (C) 81 (D) 90
Q. 6 ? Q. 10 carry two marks each.
Q.6 For integers ?? , ?? and ?? , what would be the minimum and maximum values respectively of
?? + ?? + ?? if log |?? | + log |?? | + log |?? | = 0?
(A) -3 and 3 (B) -1 and 1 (C) -1 and 3 (D) 1 and 3
GATE 2018 General Aptitude (GA) Set-1
GA 2/2
Q.7 Given that ?? and ?? are integers and ?? + ?? 2
?? 3
is odd, which one of the following
statements is correct?
(A) ?? and ?? are both odd (B) ?? and ?? are both even
(C) ?? is even and ?? is odd (D) ?? is odd and ?? is even
Q.8 From the time the front of a train enters a platform, it takes 25 seconds for the back of the
train to leave the platform, while travelling at a constant speed of 54 km/h. At the same
speed, it takes 14 seconds to pass a man running at 9 km/h in the same direction as the
train. What is the length of the train and that of the platform in meters, respectively?
(A) 210 and 140 (B) 162.5 and 187.5
(C) 245 and 130 (D) 175 and 200
Q.9 Which of the following functions describe the graph shown in the below figure?
(A) ?? = ||?? | + 1| ? 2 (B) ?? = ||?? | ? 1| ? 1
(C) ?? = ||?? | + 1| ? 1 (D) ?? = ||?? ? 1| ? 1|
Q.10 Consider the following three statements:
(i) Some roses are red.
(ii) All red flowers fade quickly.
(iii) Some roses fade quickly.
Which of the following statements can be logically inferred from the above statements?
(A) If (i) is true and (ii) is false, then (iii) is false.
(B) If (i) is true and (ii) is false, then (iii) is true.
(C) If (i) and (ii) are true, then (iii) is true.
(D) If (i) and (ii) are false, then (iii) is false.
END OF THE QUESTION PAPER
GATE 2018 Petroleum Engineering
PE 1/17
Q. 1 ? Q. 25 carry one mark each.
Q.1 The Taylor series expansion of the function,
?? (?? ) =
?1
1+?? ,
around ?? = 0 (up to 4
th
order term) is:
(A) 1 + ?? + ?? 2
+ ?? 3
+ ?? 4
(B) ?1 + ?? ? ?? 2
+ ?? 3
? ?? 4
(C) ?1 ? ?? + ?? 2
? ?? 3
+ ?? 4
(D) ?1 + ?? ? 2?? 2
+ 3?? 3
? 4?? 4
Q.2
The inverse of the matrix [
1 3
1 2
] is,
(A) [
2 3
1 1
] (B) [
?2 1
3 ?1
] (C) [
?2 3
1 ?1
] (D) [
2 ?3
?1 1
]
Q.3 The line integral of a vector function ?? ?
(?? ? ) over a curve C in a simply connected domain D
in space, is defined by:
? ?? ?
(?? ? ). ?? ?? ?
?? = ? (?? 1
???? + ?? 2
???? + ?? 3
???? )
??
The line integral is independent of path in D. ?? 1
, ?? 2
, and ?? 3
are continuous, and have
continuous first partial derivatives in D. ?? ?
is a closed curve in D.
Which one of the following is NOT ALWAYS true in domain D?
(A) ?
?
? ?? ?
= 0
?
(B) ?
?
. ?? ?
= 0
(C) ? ?? ?
(?? ? ). ?? ?? ?
?? ?
= 0
(D) ?? ?
? ?? ?
= 0
?
Q.4 Which one of the following is the integrating factor (IF) for the differential equation,
(cos
2
?? )
????
????
+ ?? = cos?? ?
(A) ?? tan ?? (B) ?? cos ??
(C) ?? ? tan ?? (D) ?? sin ??
GATE 2018 Petroleum Engineering
PE 2/17
Q.5 A phase diagram of a black oil is shown in the figure (Y is the critical point).
Match the following:
(P) Curve XY (I) Dew point curve
(Q) Curve YZ (II) Single phase liquid
(R) Phase I (III) Bubble point curve
(S) Phase II (IV) Single phase gas
(A) P-I, Q-III, R-II, S-IV (B) P-III, Q-I, R-II, S-IV
(C) P-III, Q-I, R-IV, S-II (D) P-I, Q-II, R-III, S-IV
Q.6 Match the following chemicals to their respective oilfield applications:
(P) Hydrate inhibitor (I) Formaldehyde
(Q) Well stimulation (II) Xanthan gum
(R) Drilling fluid biocide (III) Methanol
(S) Viscosifier (IV) Hydrochloric acid
(A) P-IV, Q-III, R-II, S-I (B) P-III, Q-I, R-IV, S-II
(C) P-I, Q-III R-IV, S-II (D) P-III, Q-IV, R-I, S-II
GATE 2018 Petroleum Engineering
PE 3/17
Q.7 The CH4-hydrate equilibrium curve (dashed) and CO2-hydrate equilibrium curve (solid) on
a pressure-temperature plane above 0?C are shown in the figure. The two curves divide the
plane in four non-overlapping regions. In which region are CO2-hydrates stable and CH4-
hydrates unstable?
(A) I (B) II (C) III (D) IV
Q.8 Plot of ratio of pressure to gas compressibility factor (P/Z) vs. cumulative gas production
(Gp) for a gas reservoir (represented by solid curve in the figure) was shown to a reservoir
engineering student.
The student made the following statements:
(I) A water aquifer is attached to this gas reservoir.
(II) P/Z vs. Gp curve must always be a straight line for water encroachment in a gas
reservoir.
(III) The ultimate gas recovery is diminished due to water encroachment.
Which of the above statements are TRUE?
(A) Only I and II (B) Only II and III (C) Only I and III (D) I, II, and III
Q.9 Waste water from oil industry consists of oil in free and emulsified forms. The oil in the
free form can be recovered by:
(A) Aerated lagoons
(B) Trickling filters
(C) Gravity separators
(D) Biological oxygen pond
P/Z
G p
GATE 2018 Petroleum Engineering
PE 4/17
Q.10 A reservoir model consisting of two porous matrices M and N, separated by a fracture, is
shown in the figure. The matrices are strongly water-wet and are saturated with oil of
specific gravity 0.8. Water is injected only in the fracture at injection well A. If the
Reynolds number for the flow in the fracture conduit is assumed to be less than unity, which
one of the following force will dominate oil recovery from the porous matrix M during the
water-flood operation?
(A) Capillary force (B) Gravity force
(C) Viscous force (D) Inertial force
Q.11 A fractional flow curve is given for a core for which the irreducible water saturation is 0.2
and the residual oil saturation is 0.3. The initial water saturation in the core is 0.3. If
Welge?s method is applied to find the breakthrough saturation and fraction flow of water at
breakthrough, which point should be used in the figure to draw a tangent line to the
fractional flow curve.
(A) I (B) II (C) III (D) IV
Injection well A Production well B
Matrix M
Matrix N
Fracture
GATE 2018 Petroleum Engineering
PE 5/17
Q.12 Which one of the following curves represents behavior of oil phase viscosity as a function
of pressure in the reservoir (where, Pb is the bubble point pressure of oil)?
(A) Curve I (B) Curve II (C) Curve III (D) Curve IV
Q.13 Pick out the INCORRECT statement.
(A) Flash point is always lower than fire point.
(B) Pour point of lube oil can be reduced by removing the wax from it.
(C) Fracturing is a well stimulation technique.
(D) Coal bed methane typically contains more than 60% CO2.
Q.14 Which one of the following phenomena encountered during flooding is desirable for
increasing oil recovery from a reservoir?
(A) Viscous fingering (B) Formation damage
(C) Increase in mobility ratio (D) Decrease in capillary pressure
Q.15 CO2 foams are used for enhanced oil recovery due to which of the following reasons?
(I) It can be used for CO2 sequestration
(II) CO2 can exist in the form of a dense fluid at reservoir conditions
(III) CO2 can convert to hydrocarbon at the reservoir temperature and pressure
(IV) Solubility of CO2 in oil is higher compared to gases like N2
(A) Only I, II, and III (B) Only I, II, and IV
(C) Only II, III, and IV (D) Only I, III, and IV
GATE 2018 Petroleum Engineering
PE 6/17
Q.16 Which one of the following is FALSE about a typical offshore deepwater oil spill?
(A) Using boom boats to prevent spilled oil from spreading
(B) Allowing the spill to reach the shore before clearing
(C) Burning of spilled oil
(D) Using a skimmer to collect the oil
Q.17 Which one of these methods is NOT commonly used to deal with the problem of soil
contamination by oil spillage?
(A) Biodegradation
(B) Leaching out the oil
(C) Soil recycling
(D) Using rain water to wash the contaminants
Q.18 The factor on which the selection of an offshore platform for the reservoir does NOT
depend:
(A) Water depth
(B) Reservoir fluid properties
(C) Sea bed conditions
(D) Best case weather forecast
Q.19 Which one of the following options is correct about the effects of steam stimulation in
increasing the oil production rate?
(I) Reduces the oil viscosity
(II) Increases the formation damage
(III) Reduces the interfacial tension
(IV) Increases the oil viscosity
(A) Only I and II
(B) Only II and III
(C) Only III and IV
(D) Only I and III
Q.20 Which one of the following is INCORRECT about oil based drilling muds?
(A) Good rheological properties at higher temperatures (as high as 250
o
C)
(B) Effective against corrosion
(C) Detection of gas kick is difficult
(D) Less inhibitive than water based muds
Q.21 Assume that viscous, gravity, and capillary are the only dominant forces for fluid flow in a
given reservoir, a cone formed around the perforation zone will break into the well, when
(A) capillary forces are more than viscous and gravity forces.
(B) viscous forces are more than gravity forces.
(C) gravity forces are more than capillary forces.
(D) viscous and gravity forces are equal.
GATE 2018 Petroleum Engineering
PE 7/17
Q.22
Two complex numbers, ?? ?
and ?? ? are related as follows:
?? ?
=
?? ?
????
where, ?? = ??1 and ?? is a scalar. Given principal argument of ?? ? , Arg (?? ? ) = ?
2?? 3
, the
principal argument of ?? ?
, Arg(?? ?
) =______________. (rounded-off to two decimal places.
Use ?? = 3.14)
Q.23 A cylindrical sandstone core, 7.5 cm long and 3.5 cm diameter has grain density of
3 g/cm
3
. If the mass of the dry core is 200 g, the porosity of the core is __________%.
(rounded-off to two decimal places)
Q.24 In an oil reservoir the current average pressure is below bubble point pressure of the oil.
The current oil production rate is 10
3
m
3
/day and total gas production rate is 10
5
m
3
/day at
STP conditions (25?C and 1 atm). The formation volume factor of the oil is
1.2
m
3
at reservoir pressure
m
3
at STP
and that of gas is 0.01
m
3
at reservoir pressure
m
3
at STP
. The
dissolved gas oil ratio is 10
m
3
of gas at STP
m
3
of oil at STP
of oil.
The gas flow rate at bottom-hole conditions is ______? 10
2
m
3
per day. (rounded-off to
two decimal places)
Q.25 Exponential decline curve is to be used to estimate the oil reserves of a well. The current
oil production rate is 1000 m
3
per day and yearly decline rate is 6% per year. If the
minimum oil flow rate economically sustainable for the well is 1 m
3
per day, the reserves
(economically producible) associated with the well are _____ ? 10
6
m
3
. (rounded-off to
two decimal places. Use 1 year = 365 days)
GATE 2018 Petroleum Engineering
PE 8/17
Q. 26 ? Q. 55 carry two marks each.
Q.26 The probability density for three binomial distributions (D1, D2, and D3) is plotted against
number of successful trials in the given figure.
Each of the plotted distributions corresponds to a unique pair of (n, p) values, where, n is
the number of trials and p is the probability of success in a trial. Three sets of (n, p) values
are provided in the table.
Set (n, p)
I (60, 0.3)
II (60, 0.2)
III (24, 0.5)
Pick the correct match between the (n, p) set and the plotted distribution.
(A) Set I ? D1, Set II ? D2, Set III ? D3
(B) Set I ? D3, Set II ? D1, Set III ? D2
(C) Set I ? D2, Set II ? D3, Set III ? D1
(D) Set I ? D2, Set II ? D1, Set III ? D3
Q.27 Which of the following statements are true about Natural Gas Hydrates?
Natural gas hydrates:
(I) are formed under low temperature and high pressure.
(II) can store approximately 160 m
3
of gas per m
3
of hydrate at 25
o
C and 1 atm.
(III) formation is an endothermic process.
(IV) are potential sources of methane.
(A) Only II, III & IV (B) Only I, II & III
(C) Only I, II & IV (D) Only I, III & IV
0
0.05
0.1
0.15
0 10 20 30
Probability density
Number of successful trials
D1
D2
D3
GATE 2018 Petroleum Engineering
PE 9/17
Q.28 P wf (bottom-hole well flowing pressure) vs. Q (flow rate) plots show the inflow
performance relation (IPR) and vertical lift performance (VLP) curves. Figure I shows
VLP curves for two well head pressures Phw1 and Phw2. Figure II shows VLP curves for two
well diameters D1 and D2. Which one of the following statements is true?
(A) Phw1 > Phw2 and D1 < D2 (B) Phw1 > Phw2 and D1 > D2
(C) Phw1 < Phw2 and D1 < D2 (D) Phw1 < Phw2 and D1 > D2
Q.29 Match the following:
(P) Weber Number (I) Ratio of inertial force to viscous force
(Q) Froude Number (II) Ratio of convective heat transfer to conductive heat
transfer
(R) Reynolds number (III) Ratio of inertial force to interfacial force
(S) Nusselt number (IV) Ratio of inertial force to gravitational force
(A) P-III, Q-IV, R-I, S-II (B) P-III, Q-II, R-I, S-IV
(C) P-II, Q-III, R-IV, S-I (D) P-IV, Q-III, R-I, S-II
Q.30 A dilute mixture of coal and sand particles, both of diameter 100 ?m and densities
1800 kg/m
3
and 2600 kg/m
3
, respectively, is to be classified by elutriation technique using
water (density 1000 kg/m
3
, viscosity 10
-3
Pa.s). Assuming Stokes law is applicable, the
minimum settling velocity of the particles in the mixture is (g = 9.81 m/s
2
):
(A) 4.36 ? 10
-3
m/s (B) 8.72 ? 10
-3
m/s
(C) 2.18 ? 10
-3
m/s (D) 1.29 ? 10
-3
m/s
GATE 2018 Petroleum Engineering
PE 10/17
Q.31 Oil flow rate and flowing bottom-hole pressure (FBHP) recorded with time during a multi-
rate well test are shown.
Let k is the reservoir permeability, h is the formation thickness and ? is the viscosity of the
oil. ??? ?? (?? ) is constant-rate dimensionless pressure drop as a function of time. The total
pressure drop till time, t, where t > t1, will be:
(A)
?? 1
?? 2???? ?
??? ?? (?? ) +
(?? 2
??? 1
)?? 2???? ?
??? ?? (?? ? ?? 1
)
(B)
?? 1
?? 2???? ?
??? ?? (?? 1
) +
(?? 2
??? 1
)?? 2???? ?
??? ?? (?? ? ?? 1
)
(C)
?? 1
?? 2???? ?
??? ?? (?? ) +
?? 2
?? 2???? ?
??? ?? (?? ? ?? 1
)
(D)
?? 1
?? 2???? ?
??? ?? (?? 1
) +
?? 2
?? 2???? ?
??? ?? (?? )
Q.32 Which one of the following options presents the correct combination?
(P) Reservoir limit test (I) Communication between wells
(Q) Modified isochronal test (II) Ideally zero flowing bottom hole pressure
(R) Interference test (III) Extended drawdown test
(S) Absolute open flow potential (IV) Drawdown and build-up test of equal duration
(A) P-II, Q-III, R-I, S-IV (B) P-IV, Q-I, R-III, S-II
(C) P-III, Q-IV, R-I, S-II (D) P-I, Q-III, R-IV, S-II
GATE 2018 Petroleum Engineering
PE 11/17
Q.33 Which one of the following options presents the correct combination?
(P) Roller Cone bits (I) Long and widely spaced teeth
(Q) PDC bits (II) Journal (Pin) angle
(R) Soft formation (III) Short and wider teeth
(S) Hard formation (IV) Size of the cutting
(T) Back rake angle (V) 1400
o
C and 6x10
5
psi
(A) P-II, Q-V, R-I, S-III, T-IV
(B) P-III, Q-IV, R-I, S-II, T-V
(C) P-III, Q-II, R-IV, S-I, T-V
(D) P-II, Q-V, R-III, S-I, T-IV
Q.34 Primary and secondary indicators of kick in a well where the indicators are:
1) flow rate increase,
2) gas, oil or water-cut muds,
3) pit volume increase,
4) flowing well with mud pump shut-off,
5) reduction in drill-pipe weight,
6) drilling break.
Which one of the following presents the correct combination?
(A) Primary (1, 3, 5) and Secondary (2, 4, 6)
(B) Primary (1, 2, 3) and Secondary (4, 5, 6)
(C) Primary (1, 2, 4) and Secondary (3, 5, 6)
(D) Primary (1, 3, 4) and Secondary (2, 5, 6)
GATE 2018 Petroleum Engineering
PE 12/17
Q.35 Relative permeability curve for the two rock types (X: solid line and Y: dashed line) are
shown in the diagram, where Sw is the fractional water saturation. Which one of the
following statements is correct about wettability and consolidated nature of the two rock
types?
(A) X is more consolidated and mixed wet, Y is less consolidated and water wet
(B) X is more consolidated and water wet, Y is less consolidated and mixed wet
(C) X is less consolidated and mixed wet, Y is more consolidated and water wet
(D) X is less consolidated and water wet, Y is more consolidated and mixed wet
Q.36 Which one of the following options presents correct combinations of exploration methods
with their respective frequency of operation?
(P) Seismic (I) ~10
6
Hz
(Q) Sonic (II) ~10
2
Hz
(R) Controlled Source EM (III) ~10
4
Hz
(S) Ultrasonic (IV) ~1 Hz
(A) P-IV, Q-II, R-I, S-III
(B) P-II, Q-III, R-IV, S-I
(C) P-II, Q-I, R-IV, S-III
(D) P-IV, Q-I, R-II, S-III
FirstRanker.com - FirstRanker's Choice
GATE 2018 General Aptitude (GA) Set-1
GA 1/2
Q. 1 ? Q. 5 carry one mark each.
Q.1 ?Going by the _________ that many hands make light work, the school _______ involved
all the students in the task .?
The words that best fill the blanks in the above sentence are
(A) principle, principal (B) principal, principle
(C) principle, principle (D) principal, principal
Q.2 ?Her _______ should not be confused with miserliness; she is ever willing to assist those in
need. ?
The word that best fills the blank in the above sentence is
(A) cleanliness (B) punctuality (C) frugality (D) greatness
Q.3 Seven machines take 7 minutes to make 7 identical toys. At the same rate, how many
minutes would it take for 100 machines to make 100 toys?
(A) 1 (B) 7 (C) 100 (D) 700
Q.4 A rectangle becomes a square when its length and breadth are reduced by 10 m and 5 m,
respectively. During this process, the rectangle loses 650 m
2
of area. What is the area of the
original rectangle in square meters?
(A) 1125 (B) 2250 (C) 2924 (D) 4500
Q.5 A number consists of two digits. The sum of the digits is 9. If 45 is subtracted from the
number, its digits are interchanged. What is the number?
(A) 63 (B) 72 (C) 81 (D) 90
Q. 6 ? Q. 10 carry two marks each.
Q.6 For integers ?? , ?? and ?? , what would be the minimum and maximum values respectively of
?? + ?? + ?? if log |?? | + log |?? | + log |?? | = 0?
(A) -3 and 3 (B) -1 and 1 (C) -1 and 3 (D) 1 and 3
GATE 2018 General Aptitude (GA) Set-1
GA 2/2
Q.7 Given that ?? and ?? are integers and ?? + ?? 2
?? 3
is odd, which one of the following
statements is correct?
(A) ?? and ?? are both odd (B) ?? and ?? are both even
(C) ?? is even and ?? is odd (D) ?? is odd and ?? is even
Q.8 From the time the front of a train enters a platform, it takes 25 seconds for the back of the
train to leave the platform, while travelling at a constant speed of 54 km/h. At the same
speed, it takes 14 seconds to pass a man running at 9 km/h in the same direction as the
train. What is the length of the train and that of the platform in meters, respectively?
(A) 210 and 140 (B) 162.5 and 187.5
(C) 245 and 130 (D) 175 and 200
Q.9 Which of the following functions describe the graph shown in the below figure?
(A) ?? = ||?? | + 1| ? 2 (B) ?? = ||?? | ? 1| ? 1
(C) ?? = ||?? | + 1| ? 1 (D) ?? = ||?? ? 1| ? 1|
Q.10 Consider the following three statements:
(i) Some roses are red.
(ii) All red flowers fade quickly.
(iii) Some roses fade quickly.
Which of the following statements can be logically inferred from the above statements?
(A) If (i) is true and (ii) is false, then (iii) is false.
(B) If (i) is true and (ii) is false, then (iii) is true.
(C) If (i) and (ii) are true, then (iii) is true.
(D) If (i) and (ii) are false, then (iii) is false.
END OF THE QUESTION PAPER
GATE 2018 Petroleum Engineering
PE 1/17
Q. 1 ? Q. 25 carry one mark each.
Q.1 The Taylor series expansion of the function,
?? (?? ) =
?1
1+?? ,
around ?? = 0 (up to 4
th
order term) is:
(A) 1 + ?? + ?? 2
+ ?? 3
+ ?? 4
(B) ?1 + ?? ? ?? 2
+ ?? 3
? ?? 4
(C) ?1 ? ?? + ?? 2
? ?? 3
+ ?? 4
(D) ?1 + ?? ? 2?? 2
+ 3?? 3
? 4?? 4
Q.2
The inverse of the matrix [
1 3
1 2
] is,
(A) [
2 3
1 1
] (B) [
?2 1
3 ?1
] (C) [
?2 3
1 ?1
] (D) [
2 ?3
?1 1
]
Q.3 The line integral of a vector function ?? ?
(?? ? ) over a curve C in a simply connected domain D
in space, is defined by:
? ?? ?
(?? ? ). ?? ?? ?
?? = ? (?? 1
???? + ?? 2
???? + ?? 3
???? )
??
The line integral is independent of path in D. ?? 1
, ?? 2
, and ?? 3
are continuous, and have
continuous first partial derivatives in D. ?? ?
is a closed curve in D.
Which one of the following is NOT ALWAYS true in domain D?
(A) ?
?
? ?? ?
= 0
?
(B) ?
?
. ?? ?
= 0
(C) ? ?? ?
(?? ? ). ?? ?? ?
?? ?
= 0
(D) ?? ?
? ?? ?
= 0
?
Q.4 Which one of the following is the integrating factor (IF) for the differential equation,
(cos
2
?? )
????
????
+ ?? = cos?? ?
(A) ?? tan ?? (B) ?? cos ??
(C) ?? ? tan ?? (D) ?? sin ??
GATE 2018 Petroleum Engineering
PE 2/17
Q.5 A phase diagram of a black oil is shown in the figure (Y is the critical point).
Match the following:
(P) Curve XY (I) Dew point curve
(Q) Curve YZ (II) Single phase liquid
(R) Phase I (III) Bubble point curve
(S) Phase II (IV) Single phase gas
(A) P-I, Q-III, R-II, S-IV (B) P-III, Q-I, R-II, S-IV
(C) P-III, Q-I, R-IV, S-II (D) P-I, Q-II, R-III, S-IV
Q.6 Match the following chemicals to their respective oilfield applications:
(P) Hydrate inhibitor (I) Formaldehyde
(Q) Well stimulation (II) Xanthan gum
(R) Drilling fluid biocide (III) Methanol
(S) Viscosifier (IV) Hydrochloric acid
(A) P-IV, Q-III, R-II, S-I (B) P-III, Q-I, R-IV, S-II
(C) P-I, Q-III R-IV, S-II (D) P-III, Q-IV, R-I, S-II
GATE 2018 Petroleum Engineering
PE 3/17
Q.7 The CH4-hydrate equilibrium curve (dashed) and CO2-hydrate equilibrium curve (solid) on
a pressure-temperature plane above 0?C are shown in the figure. The two curves divide the
plane in four non-overlapping regions. In which region are CO2-hydrates stable and CH4-
hydrates unstable?
(A) I (B) II (C) III (D) IV
Q.8 Plot of ratio of pressure to gas compressibility factor (P/Z) vs. cumulative gas production
(Gp) for a gas reservoir (represented by solid curve in the figure) was shown to a reservoir
engineering student.
The student made the following statements:
(I) A water aquifer is attached to this gas reservoir.
(II) P/Z vs. Gp curve must always be a straight line for water encroachment in a gas
reservoir.
(III) The ultimate gas recovery is diminished due to water encroachment.
Which of the above statements are TRUE?
(A) Only I and II (B) Only II and III (C) Only I and III (D) I, II, and III
Q.9 Waste water from oil industry consists of oil in free and emulsified forms. The oil in the
free form can be recovered by:
(A) Aerated lagoons
(B) Trickling filters
(C) Gravity separators
(D) Biological oxygen pond
P/Z
G p
GATE 2018 Petroleum Engineering
PE 4/17
Q.10 A reservoir model consisting of two porous matrices M and N, separated by a fracture, is
shown in the figure. The matrices are strongly water-wet and are saturated with oil of
specific gravity 0.8. Water is injected only in the fracture at injection well A. If the
Reynolds number for the flow in the fracture conduit is assumed to be less than unity, which
one of the following force will dominate oil recovery from the porous matrix M during the
water-flood operation?
(A) Capillary force (B) Gravity force
(C) Viscous force (D) Inertial force
Q.11 A fractional flow curve is given for a core for which the irreducible water saturation is 0.2
and the residual oil saturation is 0.3. The initial water saturation in the core is 0.3. If
Welge?s method is applied to find the breakthrough saturation and fraction flow of water at
breakthrough, which point should be used in the figure to draw a tangent line to the
fractional flow curve.
(A) I (B) II (C) III (D) IV
Injection well A Production well B
Matrix M
Matrix N
Fracture
GATE 2018 Petroleum Engineering
PE 5/17
Q.12 Which one of the following curves represents behavior of oil phase viscosity as a function
of pressure in the reservoir (where, Pb is the bubble point pressure of oil)?
(A) Curve I (B) Curve II (C) Curve III (D) Curve IV
Q.13 Pick out the INCORRECT statement.
(A) Flash point is always lower than fire point.
(B) Pour point of lube oil can be reduced by removing the wax from it.
(C) Fracturing is a well stimulation technique.
(D) Coal bed methane typically contains more than 60% CO2.
Q.14 Which one of the following phenomena encountered during flooding is desirable for
increasing oil recovery from a reservoir?
(A) Viscous fingering (B) Formation damage
(C) Increase in mobility ratio (D) Decrease in capillary pressure
Q.15 CO2 foams are used for enhanced oil recovery due to which of the following reasons?
(I) It can be used for CO2 sequestration
(II) CO2 can exist in the form of a dense fluid at reservoir conditions
(III) CO2 can convert to hydrocarbon at the reservoir temperature and pressure
(IV) Solubility of CO2 in oil is higher compared to gases like N2
(A) Only I, II, and III (B) Only I, II, and IV
(C) Only II, III, and IV (D) Only I, III, and IV
GATE 2018 Petroleum Engineering
PE 6/17
Q.16 Which one of the following is FALSE about a typical offshore deepwater oil spill?
(A) Using boom boats to prevent spilled oil from spreading
(B) Allowing the spill to reach the shore before clearing
(C) Burning of spilled oil
(D) Using a skimmer to collect the oil
Q.17 Which one of these methods is NOT commonly used to deal with the problem of soil
contamination by oil spillage?
(A) Biodegradation
(B) Leaching out the oil
(C) Soil recycling
(D) Using rain water to wash the contaminants
Q.18 The factor on which the selection of an offshore platform for the reservoir does NOT
depend:
(A) Water depth
(B) Reservoir fluid properties
(C) Sea bed conditions
(D) Best case weather forecast
Q.19 Which one of the following options is correct about the effects of steam stimulation in
increasing the oil production rate?
(I) Reduces the oil viscosity
(II) Increases the formation damage
(III) Reduces the interfacial tension
(IV) Increases the oil viscosity
(A) Only I and II
(B) Only II and III
(C) Only III and IV
(D) Only I and III
Q.20 Which one of the following is INCORRECT about oil based drilling muds?
(A) Good rheological properties at higher temperatures (as high as 250
o
C)
(B) Effective against corrosion
(C) Detection of gas kick is difficult
(D) Less inhibitive than water based muds
Q.21 Assume that viscous, gravity, and capillary are the only dominant forces for fluid flow in a
given reservoir, a cone formed around the perforation zone will break into the well, when
(A) capillary forces are more than viscous and gravity forces.
(B) viscous forces are more than gravity forces.
(C) gravity forces are more than capillary forces.
(D) viscous and gravity forces are equal.
GATE 2018 Petroleum Engineering
PE 7/17
Q.22
Two complex numbers, ?? ?
and ?? ? are related as follows:
?? ?
=
?? ?
????
where, ?? = ??1 and ?? is a scalar. Given principal argument of ?? ? , Arg (?? ? ) = ?
2?? 3
, the
principal argument of ?? ?
, Arg(?? ?
) =______________. (rounded-off to two decimal places.
Use ?? = 3.14)
Q.23 A cylindrical sandstone core, 7.5 cm long and 3.5 cm diameter has grain density of
3 g/cm
3
. If the mass of the dry core is 200 g, the porosity of the core is __________%.
(rounded-off to two decimal places)
Q.24 In an oil reservoir the current average pressure is below bubble point pressure of the oil.
The current oil production rate is 10
3
m
3
/day and total gas production rate is 10
5
m
3
/day at
STP conditions (25?C and 1 atm). The formation volume factor of the oil is
1.2
m
3
at reservoir pressure
m
3
at STP
and that of gas is 0.01
m
3
at reservoir pressure
m
3
at STP
. The
dissolved gas oil ratio is 10
m
3
of gas at STP
m
3
of oil at STP
of oil.
The gas flow rate at bottom-hole conditions is ______? 10
2
m
3
per day. (rounded-off to
two decimal places)
Q.25 Exponential decline curve is to be used to estimate the oil reserves of a well. The current
oil production rate is 1000 m
3
per day and yearly decline rate is 6% per year. If the
minimum oil flow rate economically sustainable for the well is 1 m
3
per day, the reserves
(economically producible) associated with the well are _____ ? 10
6
m
3
. (rounded-off to
two decimal places. Use 1 year = 365 days)
GATE 2018 Petroleum Engineering
PE 8/17
Q. 26 ? Q. 55 carry two marks each.
Q.26 The probability density for three binomial distributions (D1, D2, and D3) is plotted against
number of successful trials in the given figure.
Each of the plotted distributions corresponds to a unique pair of (n, p) values, where, n is
the number of trials and p is the probability of success in a trial. Three sets of (n, p) values
are provided in the table.
Set (n, p)
I (60, 0.3)
II (60, 0.2)
III (24, 0.5)
Pick the correct match between the (n, p) set and the plotted distribution.
(A) Set I ? D1, Set II ? D2, Set III ? D3
(B) Set I ? D3, Set II ? D1, Set III ? D2
(C) Set I ? D2, Set II ? D3, Set III ? D1
(D) Set I ? D2, Set II ? D1, Set III ? D3
Q.27 Which of the following statements are true about Natural Gas Hydrates?
Natural gas hydrates:
(I) are formed under low temperature and high pressure.
(II) can store approximately 160 m
3
of gas per m
3
of hydrate at 25
o
C and 1 atm.
(III) formation is an endothermic process.
(IV) are potential sources of methane.
(A) Only II, III & IV (B) Only I, II & III
(C) Only I, II & IV (D) Only I, III & IV
0
0.05
0.1
0.15
0 10 20 30
Probability density
Number of successful trials
D1
D2
D3
GATE 2018 Petroleum Engineering
PE 9/17
Q.28 P wf (bottom-hole well flowing pressure) vs. Q (flow rate) plots show the inflow
performance relation (IPR) and vertical lift performance (VLP) curves. Figure I shows
VLP curves for two well head pressures Phw1 and Phw2. Figure II shows VLP curves for two
well diameters D1 and D2. Which one of the following statements is true?
(A) Phw1 > Phw2 and D1 < D2 (B) Phw1 > Phw2 and D1 > D2
(C) Phw1 < Phw2 and D1 < D2 (D) Phw1 < Phw2 and D1 > D2
Q.29 Match the following:
(P) Weber Number (I) Ratio of inertial force to viscous force
(Q) Froude Number (II) Ratio of convective heat transfer to conductive heat
transfer
(R) Reynolds number (III) Ratio of inertial force to interfacial force
(S) Nusselt number (IV) Ratio of inertial force to gravitational force
(A) P-III, Q-IV, R-I, S-II (B) P-III, Q-II, R-I, S-IV
(C) P-II, Q-III, R-IV, S-I (D) P-IV, Q-III, R-I, S-II
Q.30 A dilute mixture of coal and sand particles, both of diameter 100 ?m and densities
1800 kg/m
3
and 2600 kg/m
3
, respectively, is to be classified by elutriation technique using
water (density 1000 kg/m
3
, viscosity 10
-3
Pa.s). Assuming Stokes law is applicable, the
minimum settling velocity of the particles in the mixture is (g = 9.81 m/s
2
):
(A) 4.36 ? 10
-3
m/s (B) 8.72 ? 10
-3
m/s
(C) 2.18 ? 10
-3
m/s (D) 1.29 ? 10
-3
m/s
GATE 2018 Petroleum Engineering
PE 10/17
Q.31 Oil flow rate and flowing bottom-hole pressure (FBHP) recorded with time during a multi-
rate well test are shown.
Let k is the reservoir permeability, h is the formation thickness and ? is the viscosity of the
oil. ??? ?? (?? ) is constant-rate dimensionless pressure drop as a function of time. The total
pressure drop till time, t, where t > t1, will be:
(A)
?? 1
?? 2???? ?
??? ?? (?? ) +
(?? 2
??? 1
)?? 2???? ?
??? ?? (?? ? ?? 1
)
(B)
?? 1
?? 2???? ?
??? ?? (?? 1
) +
(?? 2
??? 1
)?? 2???? ?
??? ?? (?? ? ?? 1
)
(C)
?? 1
?? 2???? ?
??? ?? (?? ) +
?? 2
?? 2???? ?
??? ?? (?? ? ?? 1
)
(D)
?? 1
?? 2???? ?
??? ?? (?? 1
) +
?? 2
?? 2???? ?
??? ?? (?? )
Q.32 Which one of the following options presents the correct combination?
(P) Reservoir limit test (I) Communication between wells
(Q) Modified isochronal test (II) Ideally zero flowing bottom hole pressure
(R) Interference test (III) Extended drawdown test
(S) Absolute open flow potential (IV) Drawdown and build-up test of equal duration
(A) P-II, Q-III, R-I, S-IV (B) P-IV, Q-I, R-III, S-II
(C) P-III, Q-IV, R-I, S-II (D) P-I, Q-III, R-IV, S-II
GATE 2018 Petroleum Engineering
PE 11/17
Q.33 Which one of the following options presents the correct combination?
(P) Roller Cone bits (I) Long and widely spaced teeth
(Q) PDC bits (II) Journal (Pin) angle
(R) Soft formation (III) Short and wider teeth
(S) Hard formation (IV) Size of the cutting
(T) Back rake angle (V) 1400
o
C and 6x10
5
psi
(A) P-II, Q-V, R-I, S-III, T-IV
(B) P-III, Q-IV, R-I, S-II, T-V
(C) P-III, Q-II, R-IV, S-I, T-V
(D) P-II, Q-V, R-III, S-I, T-IV
Q.34 Primary and secondary indicators of kick in a well where the indicators are:
1) flow rate increase,
2) gas, oil or water-cut muds,
3) pit volume increase,
4) flowing well with mud pump shut-off,
5) reduction in drill-pipe weight,
6) drilling break.
Which one of the following presents the correct combination?
(A) Primary (1, 3, 5) and Secondary (2, 4, 6)
(B) Primary (1, 2, 3) and Secondary (4, 5, 6)
(C) Primary (1, 2, 4) and Secondary (3, 5, 6)
(D) Primary (1, 3, 4) and Secondary (2, 5, 6)
GATE 2018 Petroleum Engineering
PE 12/17
Q.35 Relative permeability curve for the two rock types (X: solid line and Y: dashed line) are
shown in the diagram, where Sw is the fractional water saturation. Which one of the
following statements is correct about wettability and consolidated nature of the two rock
types?
(A) X is more consolidated and mixed wet, Y is less consolidated and water wet
(B) X is more consolidated and water wet, Y is less consolidated and mixed wet
(C) X is less consolidated and mixed wet, Y is more consolidated and water wet
(D) X is less consolidated and water wet, Y is more consolidated and mixed wet
Q.36 Which one of the following options presents correct combinations of exploration methods
with their respective frequency of operation?
(P) Seismic (I) ~10
6
Hz
(Q) Sonic (II) ~10
2
Hz
(R) Controlled Source EM (III) ~10
4
Hz
(S) Ultrasonic (IV) ~1 Hz
(A) P-IV, Q-II, R-I, S-III
(B) P-II, Q-III, R-IV, S-I
(C) P-II, Q-I, R-IV, S-III
(D) P-IV, Q-I, R-II, S-III
GATE 2018 Petroleum Engineering
PE 13/17
Q.37 Which one of the following options presents the correct combinations?
(P) Borisov?s (I) Critical rate correlation in vertical wells with coning
(Q) Schols? (II) Horizontal well performance relation
(R) Efros? (III) Vertical well performance relation
(S) Wiggins? (IV) Critical rate correlation in horizontal wells with coning
(A) P-II, Q-IV, R-I, S-III
(B) P-IV, Q-III, R-II, S-I
(C) P-IV, Q-II, R-III, S-I
(D) P-II, Q-I, R-IV, S-III
Q.38 Which one of the following options represents the typical sequence of applying cut-offs for
pay zone identification in a conventional reservoir?
(A) porosity, saturation, shale
(B) porosity, permeability, saturation
(C) shale, porosity, saturation
(D) shale, porosity, permeability
Q.39 Which one of the following options represents the correct sequence of arrival of acoustic
wave energy recorded in a sonic log?
(A) shear, surface, compressional
(B) compressional, shear, surface
(C) surface, shear, compressional
(D) compressional, surface, shear
Q.40 The variation of the amount of salt in a tank with time is given by,
????
????
+ 0.025?? = 20 ,
where, ?? is the amount of salt in kg and ?? is the time in minutes. Given that there is no salt
in the tank initially, the time at which the amount of salt increases to 200 kg is __________
minutes. (rounded-off to two decimal places)
Q.41 Solve the given differential equation using the 2
nd
order Runge-Kutta (RK2) method:
???? ???? = ?? ? ??? ; Initial condition : ?? (?? = 0) = 4
Use the following form of RK2 method with an integration step-size, ? = 0.5:
?? 1
= ?? (?? ?? , ?? ?? ) ; ?? 2
= ?? (?? ?? + 0.5?, ?? ?? + 0.5?? 1
?)
?? ?? +1
= ?? ?? + ?? 2
?
The value of ?? (?? = 0.5) =__________________. (rounded-off to two decimal places)
FirstRanker.com - FirstRanker's Choice
GATE 2018 General Aptitude (GA) Set-1
GA 1/2
Q. 1 ? Q. 5 carry one mark each.
Q.1 ?Going by the _________ that many hands make light work, the school _______ involved
all the students in the task .?
The words that best fill the blanks in the above sentence are
(A) principle, principal (B) principal, principle
(C) principle, principle (D) principal, principal
Q.2 ?Her _______ should not be confused with miserliness; she is ever willing to assist those in
need. ?
The word that best fills the blank in the above sentence is
(A) cleanliness (B) punctuality (C) frugality (D) greatness
Q.3 Seven machines take 7 minutes to make 7 identical toys. At the same rate, how many
minutes would it take for 100 machines to make 100 toys?
(A) 1 (B) 7 (C) 100 (D) 700
Q.4 A rectangle becomes a square when its length and breadth are reduced by 10 m and 5 m,
respectively. During this process, the rectangle loses 650 m
2
of area. What is the area of the
original rectangle in square meters?
(A) 1125 (B) 2250 (C) 2924 (D) 4500
Q.5 A number consists of two digits. The sum of the digits is 9. If 45 is subtracted from the
number, its digits are interchanged. What is the number?
(A) 63 (B) 72 (C) 81 (D) 90
Q. 6 ? Q. 10 carry two marks each.
Q.6 For integers ?? , ?? and ?? , what would be the minimum and maximum values respectively of
?? + ?? + ?? if log |?? | + log |?? | + log |?? | = 0?
(A) -3 and 3 (B) -1 and 1 (C) -1 and 3 (D) 1 and 3
GATE 2018 General Aptitude (GA) Set-1
GA 2/2
Q.7 Given that ?? and ?? are integers and ?? + ?? 2
?? 3
is odd, which one of the following
statements is correct?
(A) ?? and ?? are both odd (B) ?? and ?? are both even
(C) ?? is even and ?? is odd (D) ?? is odd and ?? is even
Q.8 From the time the front of a train enters a platform, it takes 25 seconds for the back of the
train to leave the platform, while travelling at a constant speed of 54 km/h. At the same
speed, it takes 14 seconds to pass a man running at 9 km/h in the same direction as the
train. What is the length of the train and that of the platform in meters, respectively?
(A) 210 and 140 (B) 162.5 and 187.5
(C) 245 and 130 (D) 175 and 200
Q.9 Which of the following functions describe the graph shown in the below figure?
(A) ?? = ||?? | + 1| ? 2 (B) ?? = ||?? | ? 1| ? 1
(C) ?? = ||?? | + 1| ? 1 (D) ?? = ||?? ? 1| ? 1|
Q.10 Consider the following three statements:
(i) Some roses are red.
(ii) All red flowers fade quickly.
(iii) Some roses fade quickly.
Which of the following statements can be logically inferred from the above statements?
(A) If (i) is true and (ii) is false, then (iii) is false.
(B) If (i) is true and (ii) is false, then (iii) is true.
(C) If (i) and (ii) are true, then (iii) is true.
(D) If (i) and (ii) are false, then (iii) is false.
END OF THE QUESTION PAPER
GATE 2018 Petroleum Engineering
PE 1/17
Q. 1 ? Q. 25 carry one mark each.
Q.1 The Taylor series expansion of the function,
?? (?? ) =
?1
1+?? ,
around ?? = 0 (up to 4
th
order term) is:
(A) 1 + ?? + ?? 2
+ ?? 3
+ ?? 4
(B) ?1 + ?? ? ?? 2
+ ?? 3
? ?? 4
(C) ?1 ? ?? + ?? 2
? ?? 3
+ ?? 4
(D) ?1 + ?? ? 2?? 2
+ 3?? 3
? 4?? 4
Q.2
The inverse of the matrix [
1 3
1 2
] is,
(A) [
2 3
1 1
] (B) [
?2 1
3 ?1
] (C) [
?2 3
1 ?1
] (D) [
2 ?3
?1 1
]
Q.3 The line integral of a vector function ?? ?
(?? ? ) over a curve C in a simply connected domain D
in space, is defined by:
? ?? ?
(?? ? ). ?? ?? ?
?? = ? (?? 1
???? + ?? 2
???? + ?? 3
???? )
??
The line integral is independent of path in D. ?? 1
, ?? 2
, and ?? 3
are continuous, and have
continuous first partial derivatives in D. ?? ?
is a closed curve in D.
Which one of the following is NOT ALWAYS true in domain D?
(A) ?
?
? ?? ?
= 0
?
(B) ?
?
. ?? ?
= 0
(C) ? ?? ?
(?? ? ). ?? ?? ?
?? ?
= 0
(D) ?? ?
? ?? ?
= 0
?
Q.4 Which one of the following is the integrating factor (IF) for the differential equation,
(cos
2
?? )
????
????
+ ?? = cos?? ?
(A) ?? tan ?? (B) ?? cos ??
(C) ?? ? tan ?? (D) ?? sin ??
GATE 2018 Petroleum Engineering
PE 2/17
Q.5 A phase diagram of a black oil is shown in the figure (Y is the critical point).
Match the following:
(P) Curve XY (I) Dew point curve
(Q) Curve YZ (II) Single phase liquid
(R) Phase I (III) Bubble point curve
(S) Phase II (IV) Single phase gas
(A) P-I, Q-III, R-II, S-IV (B) P-III, Q-I, R-II, S-IV
(C) P-III, Q-I, R-IV, S-II (D) P-I, Q-II, R-III, S-IV
Q.6 Match the following chemicals to their respective oilfield applications:
(P) Hydrate inhibitor (I) Formaldehyde
(Q) Well stimulation (II) Xanthan gum
(R) Drilling fluid biocide (III) Methanol
(S) Viscosifier (IV) Hydrochloric acid
(A) P-IV, Q-III, R-II, S-I (B) P-III, Q-I, R-IV, S-II
(C) P-I, Q-III R-IV, S-II (D) P-III, Q-IV, R-I, S-II
GATE 2018 Petroleum Engineering
PE 3/17
Q.7 The CH4-hydrate equilibrium curve (dashed) and CO2-hydrate equilibrium curve (solid) on
a pressure-temperature plane above 0?C are shown in the figure. The two curves divide the
plane in four non-overlapping regions. In which region are CO2-hydrates stable and CH4-
hydrates unstable?
(A) I (B) II (C) III (D) IV
Q.8 Plot of ratio of pressure to gas compressibility factor (P/Z) vs. cumulative gas production
(Gp) for a gas reservoir (represented by solid curve in the figure) was shown to a reservoir
engineering student.
The student made the following statements:
(I) A water aquifer is attached to this gas reservoir.
(II) P/Z vs. Gp curve must always be a straight line for water encroachment in a gas
reservoir.
(III) The ultimate gas recovery is diminished due to water encroachment.
Which of the above statements are TRUE?
(A) Only I and II (B) Only II and III (C) Only I and III (D) I, II, and III
Q.9 Waste water from oil industry consists of oil in free and emulsified forms. The oil in the
free form can be recovered by:
(A) Aerated lagoons
(B) Trickling filters
(C) Gravity separators
(D) Biological oxygen pond
P/Z
G p
GATE 2018 Petroleum Engineering
PE 4/17
Q.10 A reservoir model consisting of two porous matrices M and N, separated by a fracture, is
shown in the figure. The matrices are strongly water-wet and are saturated with oil of
specific gravity 0.8. Water is injected only in the fracture at injection well A. If the
Reynolds number for the flow in the fracture conduit is assumed to be less than unity, which
one of the following force will dominate oil recovery from the porous matrix M during the
water-flood operation?
(A) Capillary force (B) Gravity force
(C) Viscous force (D) Inertial force
Q.11 A fractional flow curve is given for a core for which the irreducible water saturation is 0.2
and the residual oil saturation is 0.3. The initial water saturation in the core is 0.3. If
Welge?s method is applied to find the breakthrough saturation and fraction flow of water at
breakthrough, which point should be used in the figure to draw a tangent line to the
fractional flow curve.
(A) I (B) II (C) III (D) IV
Injection well A Production well B
Matrix M
Matrix N
Fracture
GATE 2018 Petroleum Engineering
PE 5/17
Q.12 Which one of the following curves represents behavior of oil phase viscosity as a function
of pressure in the reservoir (where, Pb is the bubble point pressure of oil)?
(A) Curve I (B) Curve II (C) Curve III (D) Curve IV
Q.13 Pick out the INCORRECT statement.
(A) Flash point is always lower than fire point.
(B) Pour point of lube oil can be reduced by removing the wax from it.
(C) Fracturing is a well stimulation technique.
(D) Coal bed methane typically contains more than 60% CO2.
Q.14 Which one of the following phenomena encountered during flooding is desirable for
increasing oil recovery from a reservoir?
(A) Viscous fingering (B) Formation damage
(C) Increase in mobility ratio (D) Decrease in capillary pressure
Q.15 CO2 foams are used for enhanced oil recovery due to which of the following reasons?
(I) It can be used for CO2 sequestration
(II) CO2 can exist in the form of a dense fluid at reservoir conditions
(III) CO2 can convert to hydrocarbon at the reservoir temperature and pressure
(IV) Solubility of CO2 in oil is higher compared to gases like N2
(A) Only I, II, and III (B) Only I, II, and IV
(C) Only II, III, and IV (D) Only I, III, and IV
GATE 2018 Petroleum Engineering
PE 6/17
Q.16 Which one of the following is FALSE about a typical offshore deepwater oil spill?
(A) Using boom boats to prevent spilled oil from spreading
(B) Allowing the spill to reach the shore before clearing
(C) Burning of spilled oil
(D) Using a skimmer to collect the oil
Q.17 Which one of these methods is NOT commonly used to deal with the problem of soil
contamination by oil spillage?
(A) Biodegradation
(B) Leaching out the oil
(C) Soil recycling
(D) Using rain water to wash the contaminants
Q.18 The factor on which the selection of an offshore platform for the reservoir does NOT
depend:
(A) Water depth
(B) Reservoir fluid properties
(C) Sea bed conditions
(D) Best case weather forecast
Q.19 Which one of the following options is correct about the effects of steam stimulation in
increasing the oil production rate?
(I) Reduces the oil viscosity
(II) Increases the formation damage
(III) Reduces the interfacial tension
(IV) Increases the oil viscosity
(A) Only I and II
(B) Only II and III
(C) Only III and IV
(D) Only I and III
Q.20 Which one of the following is INCORRECT about oil based drilling muds?
(A) Good rheological properties at higher temperatures (as high as 250
o
C)
(B) Effective against corrosion
(C) Detection of gas kick is difficult
(D) Less inhibitive than water based muds
Q.21 Assume that viscous, gravity, and capillary are the only dominant forces for fluid flow in a
given reservoir, a cone formed around the perforation zone will break into the well, when
(A) capillary forces are more than viscous and gravity forces.
(B) viscous forces are more than gravity forces.
(C) gravity forces are more than capillary forces.
(D) viscous and gravity forces are equal.
GATE 2018 Petroleum Engineering
PE 7/17
Q.22
Two complex numbers, ?? ?
and ?? ? are related as follows:
?? ?
=
?? ?
????
where, ?? = ??1 and ?? is a scalar. Given principal argument of ?? ? , Arg (?? ? ) = ?
2?? 3
, the
principal argument of ?? ?
, Arg(?? ?
) =______________. (rounded-off to two decimal places.
Use ?? = 3.14)
Q.23 A cylindrical sandstone core, 7.5 cm long and 3.5 cm diameter has grain density of
3 g/cm
3
. If the mass of the dry core is 200 g, the porosity of the core is __________%.
(rounded-off to two decimal places)
Q.24 In an oil reservoir the current average pressure is below bubble point pressure of the oil.
The current oil production rate is 10
3
m
3
/day and total gas production rate is 10
5
m
3
/day at
STP conditions (25?C and 1 atm). The formation volume factor of the oil is
1.2
m
3
at reservoir pressure
m
3
at STP
and that of gas is 0.01
m
3
at reservoir pressure
m
3
at STP
. The
dissolved gas oil ratio is 10
m
3
of gas at STP
m
3
of oil at STP
of oil.
The gas flow rate at bottom-hole conditions is ______? 10
2
m
3
per day. (rounded-off to
two decimal places)
Q.25 Exponential decline curve is to be used to estimate the oil reserves of a well. The current
oil production rate is 1000 m
3
per day and yearly decline rate is 6% per year. If the
minimum oil flow rate economically sustainable for the well is 1 m
3
per day, the reserves
(economically producible) associated with the well are _____ ? 10
6
m
3
. (rounded-off to
two decimal places. Use 1 year = 365 days)
GATE 2018 Petroleum Engineering
PE 8/17
Q. 26 ? Q. 55 carry two marks each.
Q.26 The probability density for three binomial distributions (D1, D2, and D3) is plotted against
number of successful trials in the given figure.
Each of the plotted distributions corresponds to a unique pair of (n, p) values, where, n is
the number of trials and p is the probability of success in a trial. Three sets of (n, p) values
are provided in the table.
Set (n, p)
I (60, 0.3)
II (60, 0.2)
III (24, 0.5)
Pick the correct match between the (n, p) set and the plotted distribution.
(A) Set I ? D1, Set II ? D2, Set III ? D3
(B) Set I ? D3, Set II ? D1, Set III ? D2
(C) Set I ? D2, Set II ? D3, Set III ? D1
(D) Set I ? D2, Set II ? D1, Set III ? D3
Q.27 Which of the following statements are true about Natural Gas Hydrates?
Natural gas hydrates:
(I) are formed under low temperature and high pressure.
(II) can store approximately 160 m
3
of gas per m
3
of hydrate at 25
o
C and 1 atm.
(III) formation is an endothermic process.
(IV) are potential sources of methane.
(A) Only II, III & IV (B) Only I, II & III
(C) Only I, II & IV (D) Only I, III & IV
0
0.05
0.1
0.15
0 10 20 30
Probability density
Number of successful trials
D1
D2
D3
GATE 2018 Petroleum Engineering
PE 9/17
Q.28 P wf (bottom-hole well flowing pressure) vs. Q (flow rate) plots show the inflow
performance relation (IPR) and vertical lift performance (VLP) curves. Figure I shows
VLP curves for two well head pressures Phw1 and Phw2. Figure II shows VLP curves for two
well diameters D1 and D2. Which one of the following statements is true?
(A) Phw1 > Phw2 and D1 < D2 (B) Phw1 > Phw2 and D1 > D2
(C) Phw1 < Phw2 and D1 < D2 (D) Phw1 < Phw2 and D1 > D2
Q.29 Match the following:
(P) Weber Number (I) Ratio of inertial force to viscous force
(Q) Froude Number (II) Ratio of convective heat transfer to conductive heat
transfer
(R) Reynolds number (III) Ratio of inertial force to interfacial force
(S) Nusselt number (IV) Ratio of inertial force to gravitational force
(A) P-III, Q-IV, R-I, S-II (B) P-III, Q-II, R-I, S-IV
(C) P-II, Q-III, R-IV, S-I (D) P-IV, Q-III, R-I, S-II
Q.30 A dilute mixture of coal and sand particles, both of diameter 100 ?m and densities
1800 kg/m
3
and 2600 kg/m
3
, respectively, is to be classified by elutriation technique using
water (density 1000 kg/m
3
, viscosity 10
-3
Pa.s). Assuming Stokes law is applicable, the
minimum settling velocity of the particles in the mixture is (g = 9.81 m/s
2
):
(A) 4.36 ? 10
-3
m/s (B) 8.72 ? 10
-3
m/s
(C) 2.18 ? 10
-3
m/s (D) 1.29 ? 10
-3
m/s
GATE 2018 Petroleum Engineering
PE 10/17
Q.31 Oil flow rate and flowing bottom-hole pressure (FBHP) recorded with time during a multi-
rate well test are shown.
Let k is the reservoir permeability, h is the formation thickness and ? is the viscosity of the
oil. ??? ?? (?? ) is constant-rate dimensionless pressure drop as a function of time. The total
pressure drop till time, t, where t > t1, will be:
(A)
?? 1
?? 2???? ?
??? ?? (?? ) +
(?? 2
??? 1
)?? 2???? ?
??? ?? (?? ? ?? 1
)
(B)
?? 1
?? 2???? ?
??? ?? (?? 1
) +
(?? 2
??? 1
)?? 2???? ?
??? ?? (?? ? ?? 1
)
(C)
?? 1
?? 2???? ?
??? ?? (?? ) +
?? 2
?? 2???? ?
??? ?? (?? ? ?? 1
)
(D)
?? 1
?? 2???? ?
??? ?? (?? 1
) +
?? 2
?? 2???? ?
??? ?? (?? )
Q.32 Which one of the following options presents the correct combination?
(P) Reservoir limit test (I) Communication between wells
(Q) Modified isochronal test (II) Ideally zero flowing bottom hole pressure
(R) Interference test (III) Extended drawdown test
(S) Absolute open flow potential (IV) Drawdown and build-up test of equal duration
(A) P-II, Q-III, R-I, S-IV (B) P-IV, Q-I, R-III, S-II
(C) P-III, Q-IV, R-I, S-II (D) P-I, Q-III, R-IV, S-II
GATE 2018 Petroleum Engineering
PE 11/17
Q.33 Which one of the following options presents the correct combination?
(P) Roller Cone bits (I) Long and widely spaced teeth
(Q) PDC bits (II) Journal (Pin) angle
(R) Soft formation (III) Short and wider teeth
(S) Hard formation (IV) Size of the cutting
(T) Back rake angle (V) 1400
o
C and 6x10
5
psi
(A) P-II, Q-V, R-I, S-III, T-IV
(B) P-III, Q-IV, R-I, S-II, T-V
(C) P-III, Q-II, R-IV, S-I, T-V
(D) P-II, Q-V, R-III, S-I, T-IV
Q.34 Primary and secondary indicators of kick in a well where the indicators are:
1) flow rate increase,
2) gas, oil or water-cut muds,
3) pit volume increase,
4) flowing well with mud pump shut-off,
5) reduction in drill-pipe weight,
6) drilling break.
Which one of the following presents the correct combination?
(A) Primary (1, 3, 5) and Secondary (2, 4, 6)
(B) Primary (1, 2, 3) and Secondary (4, 5, 6)
(C) Primary (1, 2, 4) and Secondary (3, 5, 6)
(D) Primary (1, 3, 4) and Secondary (2, 5, 6)
GATE 2018 Petroleum Engineering
PE 12/17
Q.35 Relative permeability curve for the two rock types (X: solid line and Y: dashed line) are
shown in the diagram, where Sw is the fractional water saturation. Which one of the
following statements is correct about wettability and consolidated nature of the two rock
types?
(A) X is more consolidated and mixed wet, Y is less consolidated and water wet
(B) X is more consolidated and water wet, Y is less consolidated and mixed wet
(C) X is less consolidated and mixed wet, Y is more consolidated and water wet
(D) X is less consolidated and water wet, Y is more consolidated and mixed wet
Q.36 Which one of the following options presents correct combinations of exploration methods
with their respective frequency of operation?
(P) Seismic (I) ~10
6
Hz
(Q) Sonic (II) ~10
2
Hz
(R) Controlled Source EM (III) ~10
4
Hz
(S) Ultrasonic (IV) ~1 Hz
(A) P-IV, Q-II, R-I, S-III
(B) P-II, Q-III, R-IV, S-I
(C) P-II, Q-I, R-IV, S-III
(D) P-IV, Q-I, R-II, S-III
GATE 2018 Petroleum Engineering
PE 13/17
Q.37 Which one of the following options presents the correct combinations?
(P) Borisov?s (I) Critical rate correlation in vertical wells with coning
(Q) Schols? (II) Horizontal well performance relation
(R) Efros? (III) Vertical well performance relation
(S) Wiggins? (IV) Critical rate correlation in horizontal wells with coning
(A) P-II, Q-IV, R-I, S-III
(B) P-IV, Q-III, R-II, S-I
(C) P-IV, Q-II, R-III, S-I
(D) P-II, Q-I, R-IV, S-III
Q.38 Which one of the following options represents the typical sequence of applying cut-offs for
pay zone identification in a conventional reservoir?
(A) porosity, saturation, shale
(B) porosity, permeability, saturation
(C) shale, porosity, saturation
(D) shale, porosity, permeability
Q.39 Which one of the following options represents the correct sequence of arrival of acoustic
wave energy recorded in a sonic log?
(A) shear, surface, compressional
(B) compressional, shear, surface
(C) surface, shear, compressional
(D) compressional, surface, shear
Q.40 The variation of the amount of salt in a tank with time is given by,
????
????
+ 0.025?? = 20 ,
where, ?? is the amount of salt in kg and ?? is the time in minutes. Given that there is no salt
in the tank initially, the time at which the amount of salt increases to 200 kg is __________
minutes. (rounded-off to two decimal places)
Q.41 Solve the given differential equation using the 2
nd
order Runge-Kutta (RK2) method:
???? ???? = ?? ? ??? ; Initial condition : ?? (?? = 0) = 4
Use the following form of RK2 method with an integration step-size, ? = 0.5:
?? 1
= ?? (?? ?? , ?? ?? ) ; ?? 2
= ?? (?? ?? + 0.5?, ?? ?? + 0.5?? 1
?)
?? ?? +1
= ?? ?? + ?? 2
?
The value of ?? (?? = 0.5) =__________________. (rounded-off to two decimal places)
GATE 2018 Petroleum Engineering
PE 14/17
Q.42 A box contains 100 balls of same size, of which, 25 are black and 75 are white. Out of 25
black balls, 5 have a red dot. A trial consists of randomly picking a ball and putting it back
in the same box, i.e., sampling is done with replacement. Two such trials are done.
The conditional probability that no black ball with a red dot is picked given that at least
one black ball is picked, is __________. (in fraction rounded-off to two decimal places)
Q.43 A cylindrical pipeline of length 30 km is transporting naphtha. Pressure sensors are
attached along pipe length to detect leaks. Under steady-state, leak-free operation, there is a
linear pressure drop along the length (z) of the pipeline. If a leak occurs, the pressure
profile develops a kink at the leak point ?? leak
.
Assume that there is only one leak-point (4 km < ?? leak
< 27 km ) and a new steady-state is
reached. The steady-state pressure measurements at four locations along the pipe-length are
provided in the table. The location of the leak-point using the gradient intersection method
is _______________km. (rounded-off to two decimal places)
?? (km) Pressure
0 ?? 0
4 0.84?? 0
27 0.31?? 0
30 0.25?? 0
FirstRanker.com - FirstRanker's Choice
GATE 2018 General Aptitude (GA) Set-1
GA 1/2
Q. 1 ? Q. 5 carry one mark each.
Q.1 ?Going by the _________ that many hands make light work, the school _______ involved
all the students in the task .?
The words that best fill the blanks in the above sentence are
(A) principle, principal (B) principal, principle
(C) principle, principle (D) principal, principal
Q.2 ?Her _______ should not be confused with miserliness; she is ever willing to assist those in
need. ?
The word that best fills the blank in the above sentence is
(A) cleanliness (B) punctuality (C) frugality (D) greatness
Q.3 Seven machines take 7 minutes to make 7 identical toys. At the same rate, how many
minutes would it take for 100 machines to make 100 toys?
(A) 1 (B) 7 (C) 100 (D) 700
Q.4 A rectangle becomes a square when its length and breadth are reduced by 10 m and 5 m,
respectively. During this process, the rectangle loses 650 m
2
of area. What is the area of the
original rectangle in square meters?
(A) 1125 (B) 2250 (C) 2924 (D) 4500
Q.5 A number consists of two digits. The sum of the digits is 9. If 45 is subtracted from the
number, its digits are interchanged. What is the number?
(A) 63 (B) 72 (C) 81 (D) 90
Q. 6 ? Q. 10 carry two marks each.
Q.6 For integers ?? , ?? and ?? , what would be the minimum and maximum values respectively of
?? + ?? + ?? if log |?? | + log |?? | + log |?? | = 0?
(A) -3 and 3 (B) -1 and 1 (C) -1 and 3 (D) 1 and 3
GATE 2018 General Aptitude (GA) Set-1
GA 2/2
Q.7 Given that ?? and ?? are integers and ?? + ?? 2
?? 3
is odd, which one of the following
statements is correct?
(A) ?? and ?? are both odd (B) ?? and ?? are both even
(C) ?? is even and ?? is odd (D) ?? is odd and ?? is even
Q.8 From the time the front of a train enters a platform, it takes 25 seconds for the back of the
train to leave the platform, while travelling at a constant speed of 54 km/h. At the same
speed, it takes 14 seconds to pass a man running at 9 km/h in the same direction as the
train. What is the length of the train and that of the platform in meters, respectively?
(A) 210 and 140 (B) 162.5 and 187.5
(C) 245 and 130 (D) 175 and 200
Q.9 Which of the following functions describe the graph shown in the below figure?
(A) ?? = ||?? | + 1| ? 2 (B) ?? = ||?? | ? 1| ? 1
(C) ?? = ||?? | + 1| ? 1 (D) ?? = ||?? ? 1| ? 1|
Q.10 Consider the following three statements:
(i) Some roses are red.
(ii) All red flowers fade quickly.
(iii) Some roses fade quickly.
Which of the following statements can be logically inferred from the above statements?
(A) If (i) is true and (ii) is false, then (iii) is false.
(B) If (i) is true and (ii) is false, then (iii) is true.
(C) If (i) and (ii) are true, then (iii) is true.
(D) If (i) and (ii) are false, then (iii) is false.
END OF THE QUESTION PAPER
GATE 2018 Petroleum Engineering
PE 1/17
Q. 1 ? Q. 25 carry one mark each.
Q.1 The Taylor series expansion of the function,
?? (?? ) =
?1
1+?? ,
around ?? = 0 (up to 4
th
order term) is:
(A) 1 + ?? + ?? 2
+ ?? 3
+ ?? 4
(B) ?1 + ?? ? ?? 2
+ ?? 3
? ?? 4
(C) ?1 ? ?? + ?? 2
? ?? 3
+ ?? 4
(D) ?1 + ?? ? 2?? 2
+ 3?? 3
? 4?? 4
Q.2
The inverse of the matrix [
1 3
1 2
] is,
(A) [
2 3
1 1
] (B) [
?2 1
3 ?1
] (C) [
?2 3
1 ?1
] (D) [
2 ?3
?1 1
]
Q.3 The line integral of a vector function ?? ?
(?? ? ) over a curve C in a simply connected domain D
in space, is defined by:
? ?? ?
(?? ? ). ?? ?? ?
?? = ? (?? 1
???? + ?? 2
???? + ?? 3
???? )
??
The line integral is independent of path in D. ?? 1
, ?? 2
, and ?? 3
are continuous, and have
continuous first partial derivatives in D. ?? ?
is a closed curve in D.
Which one of the following is NOT ALWAYS true in domain D?
(A) ?
?
? ?? ?
= 0
?
(B) ?
?
. ?? ?
= 0
(C) ? ?? ?
(?? ? ). ?? ?? ?
?? ?
= 0
(D) ?? ?
? ?? ?
= 0
?
Q.4 Which one of the following is the integrating factor (IF) for the differential equation,
(cos
2
?? )
????
????
+ ?? = cos?? ?
(A) ?? tan ?? (B) ?? cos ??
(C) ?? ? tan ?? (D) ?? sin ??
GATE 2018 Petroleum Engineering
PE 2/17
Q.5 A phase diagram of a black oil is shown in the figure (Y is the critical point).
Match the following:
(P) Curve XY (I) Dew point curve
(Q) Curve YZ (II) Single phase liquid
(R) Phase I (III) Bubble point curve
(S) Phase II (IV) Single phase gas
(A) P-I, Q-III, R-II, S-IV (B) P-III, Q-I, R-II, S-IV
(C) P-III, Q-I, R-IV, S-II (D) P-I, Q-II, R-III, S-IV
Q.6 Match the following chemicals to their respective oilfield applications:
(P) Hydrate inhibitor (I) Formaldehyde
(Q) Well stimulation (II) Xanthan gum
(R) Drilling fluid biocide (III) Methanol
(S) Viscosifier (IV) Hydrochloric acid
(A) P-IV, Q-III, R-II, S-I (B) P-III, Q-I, R-IV, S-II
(C) P-I, Q-III R-IV, S-II (D) P-III, Q-IV, R-I, S-II
GATE 2018 Petroleum Engineering
PE 3/17
Q.7 The CH4-hydrate equilibrium curve (dashed) and CO2-hydrate equilibrium curve (solid) on
a pressure-temperature plane above 0?C are shown in the figure. The two curves divide the
plane in four non-overlapping regions. In which region are CO2-hydrates stable and CH4-
hydrates unstable?
(A) I (B) II (C) III (D) IV
Q.8 Plot of ratio of pressure to gas compressibility factor (P/Z) vs. cumulative gas production
(Gp) for a gas reservoir (represented by solid curve in the figure) was shown to a reservoir
engineering student.
The student made the following statements:
(I) A water aquifer is attached to this gas reservoir.
(II) P/Z vs. Gp curve must always be a straight line for water encroachment in a gas
reservoir.
(III) The ultimate gas recovery is diminished due to water encroachment.
Which of the above statements are TRUE?
(A) Only I and II (B) Only II and III (C) Only I and III (D) I, II, and III
Q.9 Waste water from oil industry consists of oil in free and emulsified forms. The oil in the
free form can be recovered by:
(A) Aerated lagoons
(B) Trickling filters
(C) Gravity separators
(D) Biological oxygen pond
P/Z
G p
GATE 2018 Petroleum Engineering
PE 4/17
Q.10 A reservoir model consisting of two porous matrices M and N, separated by a fracture, is
shown in the figure. The matrices are strongly water-wet and are saturated with oil of
specific gravity 0.8. Water is injected only in the fracture at injection well A. If the
Reynolds number for the flow in the fracture conduit is assumed to be less than unity, which
one of the following force will dominate oil recovery from the porous matrix M during the
water-flood operation?
(A) Capillary force (B) Gravity force
(C) Viscous force (D) Inertial force
Q.11 A fractional flow curve is given for a core for which the irreducible water saturation is 0.2
and the residual oil saturation is 0.3. The initial water saturation in the core is 0.3. If
Welge?s method is applied to find the breakthrough saturation and fraction flow of water at
breakthrough, which point should be used in the figure to draw a tangent line to the
fractional flow curve.
(A) I (B) II (C) III (D) IV
Injection well A Production well B
Matrix M
Matrix N
Fracture
GATE 2018 Petroleum Engineering
PE 5/17
Q.12 Which one of the following curves represents behavior of oil phase viscosity as a function
of pressure in the reservoir (where, Pb is the bubble point pressure of oil)?
(A) Curve I (B) Curve II (C) Curve III (D) Curve IV
Q.13 Pick out the INCORRECT statement.
(A) Flash point is always lower than fire point.
(B) Pour point of lube oil can be reduced by removing the wax from it.
(C) Fracturing is a well stimulation technique.
(D) Coal bed methane typically contains more than 60% CO2.
Q.14 Which one of the following phenomena encountered during flooding is desirable for
increasing oil recovery from a reservoir?
(A) Viscous fingering (B) Formation damage
(C) Increase in mobility ratio (D) Decrease in capillary pressure
Q.15 CO2 foams are used for enhanced oil recovery due to which of the following reasons?
(I) It can be used for CO2 sequestration
(II) CO2 can exist in the form of a dense fluid at reservoir conditions
(III) CO2 can convert to hydrocarbon at the reservoir temperature and pressure
(IV) Solubility of CO2 in oil is higher compared to gases like N2
(A) Only I, II, and III (B) Only I, II, and IV
(C) Only II, III, and IV (D) Only I, III, and IV
GATE 2018 Petroleum Engineering
PE 6/17
Q.16 Which one of the following is FALSE about a typical offshore deepwater oil spill?
(A) Using boom boats to prevent spilled oil from spreading
(B) Allowing the spill to reach the shore before clearing
(C) Burning of spilled oil
(D) Using a skimmer to collect the oil
Q.17 Which one of these methods is NOT commonly used to deal with the problem of soil
contamination by oil spillage?
(A) Biodegradation
(B) Leaching out the oil
(C) Soil recycling
(D) Using rain water to wash the contaminants
Q.18 The factor on which the selection of an offshore platform for the reservoir does NOT
depend:
(A) Water depth
(B) Reservoir fluid properties
(C) Sea bed conditions
(D) Best case weather forecast
Q.19 Which one of the following options is correct about the effects of steam stimulation in
increasing the oil production rate?
(I) Reduces the oil viscosity
(II) Increases the formation damage
(III) Reduces the interfacial tension
(IV) Increases the oil viscosity
(A) Only I and II
(B) Only II and III
(C) Only III and IV
(D) Only I and III
Q.20 Which one of the following is INCORRECT about oil based drilling muds?
(A) Good rheological properties at higher temperatures (as high as 250
o
C)
(B) Effective against corrosion
(C) Detection of gas kick is difficult
(D) Less inhibitive than water based muds
Q.21 Assume that viscous, gravity, and capillary are the only dominant forces for fluid flow in a
given reservoir, a cone formed around the perforation zone will break into the well, when
(A) capillary forces are more than viscous and gravity forces.
(B) viscous forces are more than gravity forces.
(C) gravity forces are more than capillary forces.
(D) viscous and gravity forces are equal.
GATE 2018 Petroleum Engineering
PE 7/17
Q.22
Two complex numbers, ?? ?
and ?? ? are related as follows:
?? ?
=
?? ?
????
where, ?? = ??1 and ?? is a scalar. Given principal argument of ?? ? , Arg (?? ? ) = ?
2?? 3
, the
principal argument of ?? ?
, Arg(?? ?
) =______________. (rounded-off to two decimal places.
Use ?? = 3.14)
Q.23 A cylindrical sandstone core, 7.5 cm long and 3.5 cm diameter has grain density of
3 g/cm
3
. If the mass of the dry core is 200 g, the porosity of the core is __________%.
(rounded-off to two decimal places)
Q.24 In an oil reservoir the current average pressure is below bubble point pressure of the oil.
The current oil production rate is 10
3
m
3
/day and total gas production rate is 10
5
m
3
/day at
STP conditions (25?C and 1 atm). The formation volume factor of the oil is
1.2
m
3
at reservoir pressure
m
3
at STP
and that of gas is 0.01
m
3
at reservoir pressure
m
3
at STP
. The
dissolved gas oil ratio is 10
m
3
of gas at STP
m
3
of oil at STP
of oil.
The gas flow rate at bottom-hole conditions is ______? 10
2
m
3
per day. (rounded-off to
two decimal places)
Q.25 Exponential decline curve is to be used to estimate the oil reserves of a well. The current
oil production rate is 1000 m
3
per day and yearly decline rate is 6% per year. If the
minimum oil flow rate economically sustainable for the well is 1 m
3
per day, the reserves
(economically producible) associated with the well are _____ ? 10
6
m
3
. (rounded-off to
two decimal places. Use 1 year = 365 days)
GATE 2018 Petroleum Engineering
PE 8/17
Q. 26 ? Q. 55 carry two marks each.
Q.26 The probability density for three binomial distributions (D1, D2, and D3) is plotted against
number of successful trials in the given figure.
Each of the plotted distributions corresponds to a unique pair of (n, p) values, where, n is
the number of trials and p is the probability of success in a trial. Three sets of (n, p) values
are provided in the table.
Set (n, p)
I (60, 0.3)
II (60, 0.2)
III (24, 0.5)
Pick the correct match between the (n, p) set and the plotted distribution.
(A) Set I ? D1, Set II ? D2, Set III ? D3
(B) Set I ? D3, Set II ? D1, Set III ? D2
(C) Set I ? D2, Set II ? D3, Set III ? D1
(D) Set I ? D2, Set II ? D1, Set III ? D3
Q.27 Which of the following statements are true about Natural Gas Hydrates?
Natural gas hydrates:
(I) are formed under low temperature and high pressure.
(II) can store approximately 160 m
3
of gas per m
3
of hydrate at 25
o
C and 1 atm.
(III) formation is an endothermic process.
(IV) are potential sources of methane.
(A) Only II, III & IV (B) Only I, II & III
(C) Only I, II & IV (D) Only I, III & IV
0
0.05
0.1
0.15
0 10 20 30
Probability density
Number of successful trials
D1
D2
D3
GATE 2018 Petroleum Engineering
PE 9/17
Q.28 P wf (bottom-hole well flowing pressure) vs. Q (flow rate) plots show the inflow
performance relation (IPR) and vertical lift performance (VLP) curves. Figure I shows
VLP curves for two well head pressures Phw1 and Phw2. Figure II shows VLP curves for two
well diameters D1 and D2. Which one of the following statements is true?
(A) Phw1 > Phw2 and D1 < D2 (B) Phw1 > Phw2 and D1 > D2
(C) Phw1 < Phw2 and D1 < D2 (D) Phw1 < Phw2 and D1 > D2
Q.29 Match the following:
(P) Weber Number (I) Ratio of inertial force to viscous force
(Q) Froude Number (II) Ratio of convective heat transfer to conductive heat
transfer
(R) Reynolds number (III) Ratio of inertial force to interfacial force
(S) Nusselt number (IV) Ratio of inertial force to gravitational force
(A) P-III, Q-IV, R-I, S-II (B) P-III, Q-II, R-I, S-IV
(C) P-II, Q-III, R-IV, S-I (D) P-IV, Q-III, R-I, S-II
Q.30 A dilute mixture of coal and sand particles, both of diameter 100 ?m and densities
1800 kg/m
3
and 2600 kg/m
3
, respectively, is to be classified by elutriation technique using
water (density 1000 kg/m
3
, viscosity 10
-3
Pa.s). Assuming Stokes law is applicable, the
minimum settling velocity of the particles in the mixture is (g = 9.81 m/s
2
):
(A) 4.36 ? 10
-3
m/s (B) 8.72 ? 10
-3
m/s
(C) 2.18 ? 10
-3
m/s (D) 1.29 ? 10
-3
m/s
GATE 2018 Petroleum Engineering
PE 10/17
Q.31 Oil flow rate and flowing bottom-hole pressure (FBHP) recorded with time during a multi-
rate well test are shown.
Let k is the reservoir permeability, h is the formation thickness and ? is the viscosity of the
oil. ??? ?? (?? ) is constant-rate dimensionless pressure drop as a function of time. The total
pressure drop till time, t, where t > t1, will be:
(A)
?? 1
?? 2???? ?
??? ?? (?? ) +
(?? 2
??? 1
)?? 2???? ?
??? ?? (?? ? ?? 1
)
(B)
?? 1
?? 2???? ?
??? ?? (?? 1
) +
(?? 2
??? 1
)?? 2???? ?
??? ?? (?? ? ?? 1
)
(C)
?? 1
?? 2???? ?
??? ?? (?? ) +
?? 2
?? 2???? ?
??? ?? (?? ? ?? 1
)
(D)
?? 1
?? 2???? ?
??? ?? (?? 1
) +
?? 2
?? 2???? ?
??? ?? (?? )
Q.32 Which one of the following options presents the correct combination?
(P) Reservoir limit test (I) Communication between wells
(Q) Modified isochronal test (II) Ideally zero flowing bottom hole pressure
(R) Interference test (III) Extended drawdown test
(S) Absolute open flow potential (IV) Drawdown and build-up test of equal duration
(A) P-II, Q-III, R-I, S-IV (B) P-IV, Q-I, R-III, S-II
(C) P-III, Q-IV, R-I, S-II (D) P-I, Q-III, R-IV, S-II
GATE 2018 Petroleum Engineering
PE 11/17
Q.33 Which one of the following options presents the correct combination?
(P) Roller Cone bits (I) Long and widely spaced teeth
(Q) PDC bits (II) Journal (Pin) angle
(R) Soft formation (III) Short and wider teeth
(S) Hard formation (IV) Size of the cutting
(T) Back rake angle (V) 1400
o
C and 6x10
5
psi
(A) P-II, Q-V, R-I, S-III, T-IV
(B) P-III, Q-IV, R-I, S-II, T-V
(C) P-III, Q-II, R-IV, S-I, T-V
(D) P-II, Q-V, R-III, S-I, T-IV
Q.34 Primary and secondary indicators of kick in a well where the indicators are:
1) flow rate increase,
2) gas, oil or water-cut muds,
3) pit volume increase,
4) flowing well with mud pump shut-off,
5) reduction in drill-pipe weight,
6) drilling break.
Which one of the following presents the correct combination?
(A) Primary (1, 3, 5) and Secondary (2, 4, 6)
(B) Primary (1, 2, 3) and Secondary (4, 5, 6)
(C) Primary (1, 2, 4) and Secondary (3, 5, 6)
(D) Primary (1, 3, 4) and Secondary (2, 5, 6)
GATE 2018 Petroleum Engineering
PE 12/17
Q.35 Relative permeability curve for the two rock types (X: solid line and Y: dashed line) are
shown in the diagram, where Sw is the fractional water saturation. Which one of the
following statements is correct about wettability and consolidated nature of the two rock
types?
(A) X is more consolidated and mixed wet, Y is less consolidated and water wet
(B) X is more consolidated and water wet, Y is less consolidated and mixed wet
(C) X is less consolidated and mixed wet, Y is more consolidated and water wet
(D) X is less consolidated and water wet, Y is more consolidated and mixed wet
Q.36 Which one of the following options presents correct combinations of exploration methods
with their respective frequency of operation?
(P) Seismic (I) ~10
6
Hz
(Q) Sonic (II) ~10
2
Hz
(R) Controlled Source EM (III) ~10
4
Hz
(S) Ultrasonic (IV) ~1 Hz
(A) P-IV, Q-II, R-I, S-III
(B) P-II, Q-III, R-IV, S-I
(C) P-II, Q-I, R-IV, S-III
(D) P-IV, Q-I, R-II, S-III
GATE 2018 Petroleum Engineering
PE 13/17
Q.37 Which one of the following options presents the correct combinations?
(P) Borisov?s (I) Critical rate correlation in vertical wells with coning
(Q) Schols? (II) Horizontal well performance relation
(R) Efros? (III) Vertical well performance relation
(S) Wiggins? (IV) Critical rate correlation in horizontal wells with coning
(A) P-II, Q-IV, R-I, S-III
(B) P-IV, Q-III, R-II, S-I
(C) P-IV, Q-II, R-III, S-I
(D) P-II, Q-I, R-IV, S-III
Q.38 Which one of the following options represents the typical sequence of applying cut-offs for
pay zone identification in a conventional reservoir?
(A) porosity, saturation, shale
(B) porosity, permeability, saturation
(C) shale, porosity, saturation
(D) shale, porosity, permeability
Q.39 Which one of the following options represents the correct sequence of arrival of acoustic
wave energy recorded in a sonic log?
(A) shear, surface, compressional
(B) compressional, shear, surface
(C) surface, shear, compressional
(D) compressional, surface, shear
Q.40 The variation of the amount of salt in a tank with time is given by,
????
????
+ 0.025?? = 20 ,
where, ?? is the amount of salt in kg and ?? is the time in minutes. Given that there is no salt
in the tank initially, the time at which the amount of salt increases to 200 kg is __________
minutes. (rounded-off to two decimal places)
Q.41 Solve the given differential equation using the 2
nd
order Runge-Kutta (RK2) method:
???? ???? = ?? ? ??? ; Initial condition : ?? (?? = 0) = 4
Use the following form of RK2 method with an integration step-size, ? = 0.5:
?? 1
= ?? (?? ?? , ?? ?? ) ; ?? 2
= ?? (?? ?? + 0.5?, ?? ?? + 0.5?? 1
?)
?? ?? +1
= ?? ?? + ?? 2
?
The value of ?? (?? = 0.5) =__________________. (rounded-off to two decimal places)
GATE 2018 Petroleum Engineering
PE 14/17
Q.42 A box contains 100 balls of same size, of which, 25 are black and 75 are white. Out of 25
black balls, 5 have a red dot. A trial consists of randomly picking a ball and putting it back
in the same box, i.e., sampling is done with replacement. Two such trials are done.
The conditional probability that no black ball with a red dot is picked given that at least
one black ball is picked, is __________. (in fraction rounded-off to two decimal places)
Q.43 A cylindrical pipeline of length 30 km is transporting naphtha. Pressure sensors are
attached along pipe length to detect leaks. Under steady-state, leak-free operation, there is a
linear pressure drop along the length (z) of the pipeline. If a leak occurs, the pressure
profile develops a kink at the leak point ?? leak
.
Assume that there is only one leak-point (4 km < ?? leak
< 27 km ) and a new steady-state is
reached. The steady-state pressure measurements at four locations along the pipe-length are
provided in the table. The location of the leak-point using the gradient intersection method
is _______________km. (rounded-off to two decimal places)
?? (km) Pressure
0 ?? 0
4 0.84?? 0
27 0.31?? 0
30 0.25?? 0
GATE 2018 Petroleum Engineering
PE 15/17
Q.44 A dry core was subjected to the mercury injection test in the laboratory. Following are the
related details:
Average formation porosity = 0.2
Formation volume factor, BO = 1.2 reservoir-bbl/STB
Oil API
o
= 32, Specific gravity of water = 1.1
Hydrostatic gradient = 0.433 psi/ft
(?? ????
cos?? )
res
= 26 dyne/cm, where ?? ????
is the oil-water interfacial tension and ?? is the
contact angle
(?? ????
cos?? )
lab
= 367 dyne/cm, where ?? ????
is air- mercury interfacial tension and ?? is the
contact angle
Average drainage area = 80 acres
(1 acre-ft = 7758 bbl)
The Table shows the laboratory data for capillary pressure at different mercury saturations.
Pc (psia) Mercury saturation (SHg)
10 0.0075
17 0.25
30 0.50
108 0.70
2000 0.85
?? ?? =
2?? cos ??
?? and the average water saturation (?? ?? ) for the productive column is 0.25. The
Original Oil in Place (OOIP) in the productive column where ?? ?? ? 0.5 is ___________
MMSTB. (rounded-off to one decimal place)
Q.45 A well is drilled with water based mud. The water saturation in the completely flushed
zone (no formation fluid residual) is given by,
?? ????
= (
??
?
2
?
?? ????
?? ????
)
1/2
,
where, Rmf and Rxo are the mud filtrate resistivity and flushed zone resistivity, respectively.
Use, a = 1.0 and Rxo = 25 Rmf.
The calculated porosity (?) of the formation is ______. (in fraction rounded-off to two
decimal places)
Q.46 An oil well is tested at a flow rate (Q) of 50 BOPD. The bottom hole flowing pressure (Pwf)
is 500 psia. The shut-in pressure is 1000 psia. If Pwf is lowered to 300 psia and assuming
the Vogel?s correlation holds, the estimated flow rate in the oil well is ______BOPD
(rounded-off to two decimal places). The Vogel?s correlation is:
?? ?? ??????
= 1 ? 0.2 (
?? ????
?? ?
) ? 0.8 (
?? ????
?? ?
)
2
FirstRanker.com - FirstRanker's Choice
GATE 2018 General Aptitude (GA) Set-1
GA 1/2
Q. 1 ? Q. 5 carry one mark each.
Q.1 ?Going by the _________ that many hands make light work, the school _______ involved
all the students in the task .?
The words that best fill the blanks in the above sentence are
(A) principle, principal (B) principal, principle
(C) principle, principle (D) principal, principal
Q.2 ?Her _______ should not be confused with miserliness; she is ever willing to assist those in
need. ?
The word that best fills the blank in the above sentence is
(A) cleanliness (B) punctuality (C) frugality (D) greatness
Q.3 Seven machines take 7 minutes to make 7 identical toys. At the same rate, how many
minutes would it take for 100 machines to make 100 toys?
(A) 1 (B) 7 (C) 100 (D) 700
Q.4 A rectangle becomes a square when its length and breadth are reduced by 10 m and 5 m,
respectively. During this process, the rectangle loses 650 m
2
of area. What is the area of the
original rectangle in square meters?
(A) 1125 (B) 2250 (C) 2924 (D) 4500
Q.5 A number consists of two digits. The sum of the digits is 9. If 45 is subtracted from the
number, its digits are interchanged. What is the number?
(A) 63 (B) 72 (C) 81 (D) 90
Q. 6 ? Q. 10 carry two marks each.
Q.6 For integers ?? , ?? and ?? , what would be the minimum and maximum values respectively of
?? + ?? + ?? if log |?? | + log |?? | + log |?? | = 0?
(A) -3 and 3 (B) -1 and 1 (C) -1 and 3 (D) 1 and 3
GATE 2018 General Aptitude (GA) Set-1
GA 2/2
Q.7 Given that ?? and ?? are integers and ?? + ?? 2
?? 3
is odd, which one of the following
statements is correct?
(A) ?? and ?? are both odd (B) ?? and ?? are both even
(C) ?? is even and ?? is odd (D) ?? is odd and ?? is even
Q.8 From the time the front of a train enters a platform, it takes 25 seconds for the back of the
train to leave the platform, while travelling at a constant speed of 54 km/h. At the same
speed, it takes 14 seconds to pass a man running at 9 km/h in the same direction as the
train. What is the length of the train and that of the platform in meters, respectively?
(A) 210 and 140 (B) 162.5 and 187.5
(C) 245 and 130 (D) 175 and 200
Q.9 Which of the following functions describe the graph shown in the below figure?
(A) ?? = ||?? | + 1| ? 2 (B) ?? = ||?? | ? 1| ? 1
(C) ?? = ||?? | + 1| ? 1 (D) ?? = ||?? ? 1| ? 1|
Q.10 Consider the following three statements:
(i) Some roses are red.
(ii) All red flowers fade quickly.
(iii) Some roses fade quickly.
Which of the following statements can be logically inferred from the above statements?
(A) If (i) is true and (ii) is false, then (iii) is false.
(B) If (i) is true and (ii) is false, then (iii) is true.
(C) If (i) and (ii) are true, then (iii) is true.
(D) If (i) and (ii) are false, then (iii) is false.
END OF THE QUESTION PAPER
GATE 2018 Petroleum Engineering
PE 1/17
Q. 1 ? Q. 25 carry one mark each.
Q.1 The Taylor series expansion of the function,
?? (?? ) =
?1
1+?? ,
around ?? = 0 (up to 4
th
order term) is:
(A) 1 + ?? + ?? 2
+ ?? 3
+ ?? 4
(B) ?1 + ?? ? ?? 2
+ ?? 3
? ?? 4
(C) ?1 ? ?? + ?? 2
? ?? 3
+ ?? 4
(D) ?1 + ?? ? 2?? 2
+ 3?? 3
? 4?? 4
Q.2
The inverse of the matrix [
1 3
1 2
] is,
(A) [
2 3
1 1
] (B) [
?2 1
3 ?1
] (C) [
?2 3
1 ?1
] (D) [
2 ?3
?1 1
]
Q.3 The line integral of a vector function ?? ?
(?? ? ) over a curve C in a simply connected domain D
in space, is defined by:
? ?? ?
(?? ? ). ?? ?? ?
?? = ? (?? 1
???? + ?? 2
???? + ?? 3
???? )
??
The line integral is independent of path in D. ?? 1
, ?? 2
, and ?? 3
are continuous, and have
continuous first partial derivatives in D. ?? ?
is a closed curve in D.
Which one of the following is NOT ALWAYS true in domain D?
(A) ?
?
? ?? ?
= 0
?
(B) ?
?
. ?? ?
= 0
(C) ? ?? ?
(?? ? ). ?? ?? ?
?? ?
= 0
(D) ?? ?
? ?? ?
= 0
?
Q.4 Which one of the following is the integrating factor (IF) for the differential equation,
(cos
2
?? )
????
????
+ ?? = cos?? ?
(A) ?? tan ?? (B) ?? cos ??
(C) ?? ? tan ?? (D) ?? sin ??
GATE 2018 Petroleum Engineering
PE 2/17
Q.5 A phase diagram of a black oil is shown in the figure (Y is the critical point).
Match the following:
(P) Curve XY (I) Dew point curve
(Q) Curve YZ (II) Single phase liquid
(R) Phase I (III) Bubble point curve
(S) Phase II (IV) Single phase gas
(A) P-I, Q-III, R-II, S-IV (B) P-III, Q-I, R-II, S-IV
(C) P-III, Q-I, R-IV, S-II (D) P-I, Q-II, R-III, S-IV
Q.6 Match the following chemicals to their respective oilfield applications:
(P) Hydrate inhibitor (I) Formaldehyde
(Q) Well stimulation (II) Xanthan gum
(R) Drilling fluid biocide (III) Methanol
(S) Viscosifier (IV) Hydrochloric acid
(A) P-IV, Q-III, R-II, S-I (B) P-III, Q-I, R-IV, S-II
(C) P-I, Q-III R-IV, S-II (D) P-III, Q-IV, R-I, S-II
GATE 2018 Petroleum Engineering
PE 3/17
Q.7 The CH4-hydrate equilibrium curve (dashed) and CO2-hydrate equilibrium curve (solid) on
a pressure-temperature plane above 0?C are shown in the figure. The two curves divide the
plane in four non-overlapping regions. In which region are CO2-hydrates stable and CH4-
hydrates unstable?
(A) I (B) II (C) III (D) IV
Q.8 Plot of ratio of pressure to gas compressibility factor (P/Z) vs. cumulative gas production
(Gp) for a gas reservoir (represented by solid curve in the figure) was shown to a reservoir
engineering student.
The student made the following statements:
(I) A water aquifer is attached to this gas reservoir.
(II) P/Z vs. Gp curve must always be a straight line for water encroachment in a gas
reservoir.
(III) The ultimate gas recovery is diminished due to water encroachment.
Which of the above statements are TRUE?
(A) Only I and II (B) Only II and III (C) Only I and III (D) I, II, and III
Q.9 Waste water from oil industry consists of oil in free and emulsified forms. The oil in the
free form can be recovered by:
(A) Aerated lagoons
(B) Trickling filters
(C) Gravity separators
(D) Biological oxygen pond
P/Z
G p
GATE 2018 Petroleum Engineering
PE 4/17
Q.10 A reservoir model consisting of two porous matrices M and N, separated by a fracture, is
shown in the figure. The matrices are strongly water-wet and are saturated with oil of
specific gravity 0.8. Water is injected only in the fracture at injection well A. If the
Reynolds number for the flow in the fracture conduit is assumed to be less than unity, which
one of the following force will dominate oil recovery from the porous matrix M during the
water-flood operation?
(A) Capillary force (B) Gravity force
(C) Viscous force (D) Inertial force
Q.11 A fractional flow curve is given for a core for which the irreducible water saturation is 0.2
and the residual oil saturation is 0.3. The initial water saturation in the core is 0.3. If
Welge?s method is applied to find the breakthrough saturation and fraction flow of water at
breakthrough, which point should be used in the figure to draw a tangent line to the
fractional flow curve.
(A) I (B) II (C) III (D) IV
Injection well A Production well B
Matrix M
Matrix N
Fracture
GATE 2018 Petroleum Engineering
PE 5/17
Q.12 Which one of the following curves represents behavior of oil phase viscosity as a function
of pressure in the reservoir (where, Pb is the bubble point pressure of oil)?
(A) Curve I (B) Curve II (C) Curve III (D) Curve IV
Q.13 Pick out the INCORRECT statement.
(A) Flash point is always lower than fire point.
(B) Pour point of lube oil can be reduced by removing the wax from it.
(C) Fracturing is a well stimulation technique.
(D) Coal bed methane typically contains more than 60% CO2.
Q.14 Which one of the following phenomena encountered during flooding is desirable for
increasing oil recovery from a reservoir?
(A) Viscous fingering (B) Formation damage
(C) Increase in mobility ratio (D) Decrease in capillary pressure
Q.15 CO2 foams are used for enhanced oil recovery due to which of the following reasons?
(I) It can be used for CO2 sequestration
(II) CO2 can exist in the form of a dense fluid at reservoir conditions
(III) CO2 can convert to hydrocarbon at the reservoir temperature and pressure
(IV) Solubility of CO2 in oil is higher compared to gases like N2
(A) Only I, II, and III (B) Only I, II, and IV
(C) Only II, III, and IV (D) Only I, III, and IV
GATE 2018 Petroleum Engineering
PE 6/17
Q.16 Which one of the following is FALSE about a typical offshore deepwater oil spill?
(A) Using boom boats to prevent spilled oil from spreading
(B) Allowing the spill to reach the shore before clearing
(C) Burning of spilled oil
(D) Using a skimmer to collect the oil
Q.17 Which one of these methods is NOT commonly used to deal with the problem of soil
contamination by oil spillage?
(A) Biodegradation
(B) Leaching out the oil
(C) Soil recycling
(D) Using rain water to wash the contaminants
Q.18 The factor on which the selection of an offshore platform for the reservoir does NOT
depend:
(A) Water depth
(B) Reservoir fluid properties
(C) Sea bed conditions
(D) Best case weather forecast
Q.19 Which one of the following options is correct about the effects of steam stimulation in
increasing the oil production rate?
(I) Reduces the oil viscosity
(II) Increases the formation damage
(III) Reduces the interfacial tension
(IV) Increases the oil viscosity
(A) Only I and II
(B) Only II and III
(C) Only III and IV
(D) Only I and III
Q.20 Which one of the following is INCORRECT about oil based drilling muds?
(A) Good rheological properties at higher temperatures (as high as 250
o
C)
(B) Effective against corrosion
(C) Detection of gas kick is difficult
(D) Less inhibitive than water based muds
Q.21 Assume that viscous, gravity, and capillary are the only dominant forces for fluid flow in a
given reservoir, a cone formed around the perforation zone will break into the well, when
(A) capillary forces are more than viscous and gravity forces.
(B) viscous forces are more than gravity forces.
(C) gravity forces are more than capillary forces.
(D) viscous and gravity forces are equal.
GATE 2018 Petroleum Engineering
PE 7/17
Q.22
Two complex numbers, ?? ?
and ?? ? are related as follows:
?? ?
=
?? ?
????
where, ?? = ??1 and ?? is a scalar. Given principal argument of ?? ? , Arg (?? ? ) = ?
2?? 3
, the
principal argument of ?? ?
, Arg(?? ?
) =______________. (rounded-off to two decimal places.
Use ?? = 3.14)
Q.23 A cylindrical sandstone core, 7.5 cm long and 3.5 cm diameter has grain density of
3 g/cm
3
. If the mass of the dry core is 200 g, the porosity of the core is __________%.
(rounded-off to two decimal places)
Q.24 In an oil reservoir the current average pressure is below bubble point pressure of the oil.
The current oil production rate is 10
3
m
3
/day and total gas production rate is 10
5
m
3
/day at
STP conditions (25?C and 1 atm). The formation volume factor of the oil is
1.2
m
3
at reservoir pressure
m
3
at STP
and that of gas is 0.01
m
3
at reservoir pressure
m
3
at STP
. The
dissolved gas oil ratio is 10
m
3
of gas at STP
m
3
of oil at STP
of oil.
The gas flow rate at bottom-hole conditions is ______? 10
2
m
3
per day. (rounded-off to
two decimal places)
Q.25 Exponential decline curve is to be used to estimate the oil reserves of a well. The current
oil production rate is 1000 m
3
per day and yearly decline rate is 6% per year. If the
minimum oil flow rate economically sustainable for the well is 1 m
3
per day, the reserves
(economically producible) associated with the well are _____ ? 10
6
m
3
. (rounded-off to
two decimal places. Use 1 year = 365 days)
GATE 2018 Petroleum Engineering
PE 8/17
Q. 26 ? Q. 55 carry two marks each.
Q.26 The probability density for three binomial distributions (D1, D2, and D3) is plotted against
number of successful trials in the given figure.
Each of the plotted distributions corresponds to a unique pair of (n, p) values, where, n is
the number of trials and p is the probability of success in a trial. Three sets of (n, p) values
are provided in the table.
Set (n, p)
I (60, 0.3)
II (60, 0.2)
III (24, 0.5)
Pick the correct match between the (n, p) set and the plotted distribution.
(A) Set I ? D1, Set II ? D2, Set III ? D3
(B) Set I ? D3, Set II ? D1, Set III ? D2
(C) Set I ? D2, Set II ? D3, Set III ? D1
(D) Set I ? D2, Set II ? D1, Set III ? D3
Q.27 Which of the following statements are true about Natural Gas Hydrates?
Natural gas hydrates:
(I) are formed under low temperature and high pressure.
(II) can store approximately 160 m
3
of gas per m
3
of hydrate at 25
o
C and 1 atm.
(III) formation is an endothermic process.
(IV) are potential sources of methane.
(A) Only II, III & IV (B) Only I, II & III
(C) Only I, II & IV (D) Only I, III & IV
0
0.05
0.1
0.15
0 10 20 30
Probability density
Number of successful trials
D1
D2
D3
GATE 2018 Petroleum Engineering
PE 9/17
Q.28 P wf (bottom-hole well flowing pressure) vs. Q (flow rate) plots show the inflow
performance relation (IPR) and vertical lift performance (VLP) curves. Figure I shows
VLP curves for two well head pressures Phw1 and Phw2. Figure II shows VLP curves for two
well diameters D1 and D2. Which one of the following statements is true?
(A) Phw1 > Phw2 and D1 < D2 (B) Phw1 > Phw2 and D1 > D2
(C) Phw1 < Phw2 and D1 < D2 (D) Phw1 < Phw2 and D1 > D2
Q.29 Match the following:
(P) Weber Number (I) Ratio of inertial force to viscous force
(Q) Froude Number (II) Ratio of convective heat transfer to conductive heat
transfer
(R) Reynolds number (III) Ratio of inertial force to interfacial force
(S) Nusselt number (IV) Ratio of inertial force to gravitational force
(A) P-III, Q-IV, R-I, S-II (B) P-III, Q-II, R-I, S-IV
(C) P-II, Q-III, R-IV, S-I (D) P-IV, Q-III, R-I, S-II
Q.30 A dilute mixture of coal and sand particles, both of diameter 100 ?m and densities
1800 kg/m
3
and 2600 kg/m
3
, respectively, is to be classified by elutriation technique using
water (density 1000 kg/m
3
, viscosity 10
-3
Pa.s). Assuming Stokes law is applicable, the
minimum settling velocity of the particles in the mixture is (g = 9.81 m/s
2
):
(A) 4.36 ? 10
-3
m/s (B) 8.72 ? 10
-3
m/s
(C) 2.18 ? 10
-3
m/s (D) 1.29 ? 10
-3
m/s
GATE 2018 Petroleum Engineering
PE 10/17
Q.31 Oil flow rate and flowing bottom-hole pressure (FBHP) recorded with time during a multi-
rate well test are shown.
Let k is the reservoir permeability, h is the formation thickness and ? is the viscosity of the
oil. ??? ?? (?? ) is constant-rate dimensionless pressure drop as a function of time. The total
pressure drop till time, t, where t > t1, will be:
(A)
?? 1
?? 2???? ?
??? ?? (?? ) +
(?? 2
??? 1
)?? 2???? ?
??? ?? (?? ? ?? 1
)
(B)
?? 1
?? 2???? ?
??? ?? (?? 1
) +
(?? 2
??? 1
)?? 2???? ?
??? ?? (?? ? ?? 1
)
(C)
?? 1
?? 2???? ?
??? ?? (?? ) +
?? 2
?? 2???? ?
??? ?? (?? ? ?? 1
)
(D)
?? 1
?? 2???? ?
??? ?? (?? 1
) +
?? 2
?? 2???? ?
??? ?? (?? )
Q.32 Which one of the following options presents the correct combination?
(P) Reservoir limit test (I) Communication between wells
(Q) Modified isochronal test (II) Ideally zero flowing bottom hole pressure
(R) Interference test (III) Extended drawdown test
(S) Absolute open flow potential (IV) Drawdown and build-up test of equal duration
(A) P-II, Q-III, R-I, S-IV (B) P-IV, Q-I, R-III, S-II
(C) P-III, Q-IV, R-I, S-II (D) P-I, Q-III, R-IV, S-II
GATE 2018 Petroleum Engineering
PE 11/17
Q.33 Which one of the following options presents the correct combination?
(P) Roller Cone bits (I) Long and widely spaced teeth
(Q) PDC bits (II) Journal (Pin) angle
(R) Soft formation (III) Short and wider teeth
(S) Hard formation (IV) Size of the cutting
(T) Back rake angle (V) 1400
o
C and 6x10
5
psi
(A) P-II, Q-V, R-I, S-III, T-IV
(B) P-III, Q-IV, R-I, S-II, T-V
(C) P-III, Q-II, R-IV, S-I, T-V
(D) P-II, Q-V, R-III, S-I, T-IV
Q.34 Primary and secondary indicators of kick in a well where the indicators are:
1) flow rate increase,
2) gas, oil or water-cut muds,
3) pit volume increase,
4) flowing well with mud pump shut-off,
5) reduction in drill-pipe weight,
6) drilling break.
Which one of the following presents the correct combination?
(A) Primary (1, 3, 5) and Secondary (2, 4, 6)
(B) Primary (1, 2, 3) and Secondary (4, 5, 6)
(C) Primary (1, 2, 4) and Secondary (3, 5, 6)
(D) Primary (1, 3, 4) and Secondary (2, 5, 6)
GATE 2018 Petroleum Engineering
PE 12/17
Q.35 Relative permeability curve for the two rock types (X: solid line and Y: dashed line) are
shown in the diagram, where Sw is the fractional water saturation. Which one of the
following statements is correct about wettability and consolidated nature of the two rock
types?
(A) X is more consolidated and mixed wet, Y is less consolidated and water wet
(B) X is more consolidated and water wet, Y is less consolidated and mixed wet
(C) X is less consolidated and mixed wet, Y is more consolidated and water wet
(D) X is less consolidated and water wet, Y is more consolidated and mixed wet
Q.36 Which one of the following options presents correct combinations of exploration methods
with their respective frequency of operation?
(P) Seismic (I) ~10
6
Hz
(Q) Sonic (II) ~10
2
Hz
(R) Controlled Source EM (III) ~10
4
Hz
(S) Ultrasonic (IV) ~1 Hz
(A) P-IV, Q-II, R-I, S-III
(B) P-II, Q-III, R-IV, S-I
(C) P-II, Q-I, R-IV, S-III
(D) P-IV, Q-I, R-II, S-III
GATE 2018 Petroleum Engineering
PE 13/17
Q.37 Which one of the following options presents the correct combinations?
(P) Borisov?s (I) Critical rate correlation in vertical wells with coning
(Q) Schols? (II) Horizontal well performance relation
(R) Efros? (III) Vertical well performance relation
(S) Wiggins? (IV) Critical rate correlation in horizontal wells with coning
(A) P-II, Q-IV, R-I, S-III
(B) P-IV, Q-III, R-II, S-I
(C) P-IV, Q-II, R-III, S-I
(D) P-II, Q-I, R-IV, S-III
Q.38 Which one of the following options represents the typical sequence of applying cut-offs for
pay zone identification in a conventional reservoir?
(A) porosity, saturation, shale
(B) porosity, permeability, saturation
(C) shale, porosity, saturation
(D) shale, porosity, permeability
Q.39 Which one of the following options represents the correct sequence of arrival of acoustic
wave energy recorded in a sonic log?
(A) shear, surface, compressional
(B) compressional, shear, surface
(C) surface, shear, compressional
(D) compressional, surface, shear
Q.40 The variation of the amount of salt in a tank with time is given by,
????
????
+ 0.025?? = 20 ,
where, ?? is the amount of salt in kg and ?? is the time in minutes. Given that there is no salt
in the tank initially, the time at which the amount of salt increases to 200 kg is __________
minutes. (rounded-off to two decimal places)
Q.41 Solve the given differential equation using the 2
nd
order Runge-Kutta (RK2) method:
???? ???? = ?? ? ??? ; Initial condition : ?? (?? = 0) = 4
Use the following form of RK2 method with an integration step-size, ? = 0.5:
?? 1
= ?? (?? ?? , ?? ?? ) ; ?? 2
= ?? (?? ?? + 0.5?, ?? ?? + 0.5?? 1
?)
?? ?? +1
= ?? ?? + ?? 2
?
The value of ?? (?? = 0.5) =__________________. (rounded-off to two decimal places)
GATE 2018 Petroleum Engineering
PE 14/17
Q.42 A box contains 100 balls of same size, of which, 25 are black and 75 are white. Out of 25
black balls, 5 have a red dot. A trial consists of randomly picking a ball and putting it back
in the same box, i.e., sampling is done with replacement. Two such trials are done.
The conditional probability that no black ball with a red dot is picked given that at least
one black ball is picked, is __________. (in fraction rounded-off to two decimal places)
Q.43 A cylindrical pipeline of length 30 km is transporting naphtha. Pressure sensors are
attached along pipe length to detect leaks. Under steady-state, leak-free operation, there is a
linear pressure drop along the length (z) of the pipeline. If a leak occurs, the pressure
profile develops a kink at the leak point ?? leak
.
Assume that there is only one leak-point (4 km < ?? leak
< 27 km ) and a new steady-state is
reached. The steady-state pressure measurements at four locations along the pipe-length are
provided in the table. The location of the leak-point using the gradient intersection method
is _______________km. (rounded-off to two decimal places)
?? (km) Pressure
0 ?? 0
4 0.84?? 0
27 0.31?? 0
30 0.25?? 0
GATE 2018 Petroleum Engineering
PE 15/17
Q.44 A dry core was subjected to the mercury injection test in the laboratory. Following are the
related details:
Average formation porosity = 0.2
Formation volume factor, BO = 1.2 reservoir-bbl/STB
Oil API
o
= 32, Specific gravity of water = 1.1
Hydrostatic gradient = 0.433 psi/ft
(?? ????
cos?? )
res
= 26 dyne/cm, where ?? ????
is the oil-water interfacial tension and ?? is the
contact angle
(?? ????
cos?? )
lab
= 367 dyne/cm, where ?? ????
is air- mercury interfacial tension and ?? is the
contact angle
Average drainage area = 80 acres
(1 acre-ft = 7758 bbl)
The Table shows the laboratory data for capillary pressure at different mercury saturations.
Pc (psia) Mercury saturation (SHg)
10 0.0075
17 0.25
30 0.50
108 0.70
2000 0.85
?? ?? =
2?? cos ??
?? and the average water saturation (?? ?? ) for the productive column is 0.25. The
Original Oil in Place (OOIP) in the productive column where ?? ?? ? 0.5 is ___________
MMSTB. (rounded-off to one decimal place)
Q.45 A well is drilled with water based mud. The water saturation in the completely flushed
zone (no formation fluid residual) is given by,
?? ????
= (
??
?
2
?
?? ????
?? ????
)
1/2
,
where, Rmf and Rxo are the mud filtrate resistivity and flushed zone resistivity, respectively.
Use, a = 1.0 and Rxo = 25 Rmf.
The calculated porosity (?) of the formation is ______. (in fraction rounded-off to two
decimal places)
Q.46 An oil well is tested at a flow rate (Q) of 50 BOPD. The bottom hole flowing pressure (Pwf)
is 500 psia. The shut-in pressure is 1000 psia. If Pwf is lowered to 300 psia and assuming
the Vogel?s correlation holds, the estimated flow rate in the oil well is ______BOPD
(rounded-off to two decimal places). The Vogel?s correlation is:
?? ?? ??????
= 1 ? 0.2 (
?? ????
?? ?
) ? 0.8 (
?? ????
?? ?
)
2
GATE 2018 Petroleum Engineering
PE 16/17
Q.47 Using Miller, Dyes and Hutchinson (MDH) method, the skin factor of an oil well is found
to be ?? = ? 3.5.
The reservoir and fluid properties are:
Formation porosity is 0.20
Total compressibility is 2.5 ? 10
-5
psia
-1
Oil viscosity is 1.5 cP
Wellbore radius is 0.5 ft
Flowing bottom hole pressure at ?t = 0 is 2830 psia
Shut in pressure at ?t = 1 hr (P?t=1hr) is 3000 psia
Slope of middle time region (MTR) line in MDH plot is 190 psia/cycle.
The permeability of the reservoir is __________mD. (rounded-off to two decimal places)
Q.48 An oil well (producing under expansion drive only) in a reservoir is subjected to two
pressure build-up tests. The average formation thickness of the reservoir is 13 ft, the total
compressibility is 1?10
-5
psia
-1
, and porosity is 0.2. The average formation volume factor
of oil is 1.3 reservoir-bbl/STB. Average reservoir pressure during the first test and the
second test was found to be 3500 psia and 3200 psia, respectively.
If the oil produced between the two pressure build-up tests in 180 days is 250 STB/day, the
area of the reservoir is __________acres. (rounded-off to two decimal places)
(Use: 1 acre = 43560 ft
2
, 1 bbl = 5.615 ft
3
)
Q.49 A well in a very large reservoir has a wellbore radius of 10 cm. The sandstone, with a
porosity of 0.25 and 12% (by grain volume) calcite (CaCO3), is to be acidized with a
preflush (HCl solution) so as to dissolve all the calcite upto a distance of 1 m from the
wellbore. 1 m
3
of preflush is able to dissolve 0.082 m
3
CaCO3. Assume that the reaction
between HCl and CaCO3 is instantaneous.
The minimum preflush volume required per meter of the formation thickness is
______________m
3
. (rounded-off to two decimal places)
Q.50 At a particular temperature, the vapour pressure of benzene and toluene are 4 atm and
1.2 atm, respectively. The composition of the liquid at equilibrium is 0.5 moles of benzene
and 0.5 moles of toluene. Assuming ideal gas and ideal solution, the equilibrium vapour
phase mole fraction of benzene is ________ . (rounded-off to two decimal places)
Q.51 Saturated steam at 0.7 atm and 90?C condenses on a vertical pipe of 2 cm outside diameter
and 40 cm length. The average condensation heat transfer coefficient on the tube is
12000 W/m
2
K. The outside surface temperature of the pipe is maintained constant at 85?C.
The enthalpy values for saturated steam and condensate are 2660 kJ/kg and 375 kJ/kg,
respectively. The rate of steam condensation is ____ kg/h. (rounded-off to two decimal
places)
FirstRanker.com - FirstRanker's Choice
GATE 2018 General Aptitude (GA) Set-1
GA 1/2
Q. 1 ? Q. 5 carry one mark each.
Q.1 ?Going by the _________ that many hands make light work, the school _______ involved
all the students in the task .?
The words that best fill the blanks in the above sentence are
(A) principle, principal (B) principal, principle
(C) principle, principle (D) principal, principal
Q.2 ?Her _______ should not be confused with miserliness; she is ever willing to assist those in
need. ?
The word that best fills the blank in the above sentence is
(A) cleanliness (B) punctuality (C) frugality (D) greatness
Q.3 Seven machines take 7 minutes to make 7 identical toys. At the same rate, how many
minutes would it take for 100 machines to make 100 toys?
(A) 1 (B) 7 (C) 100 (D) 700
Q.4 A rectangle becomes a square when its length and breadth are reduced by 10 m and 5 m,
respectively. During this process, the rectangle loses 650 m
2
of area. What is the area of the
original rectangle in square meters?
(A) 1125 (B) 2250 (C) 2924 (D) 4500
Q.5 A number consists of two digits. The sum of the digits is 9. If 45 is subtracted from the
number, its digits are interchanged. What is the number?
(A) 63 (B) 72 (C) 81 (D) 90
Q. 6 ? Q. 10 carry two marks each.
Q.6 For integers ?? , ?? and ?? , what would be the minimum and maximum values respectively of
?? + ?? + ?? if log |?? | + log |?? | + log |?? | = 0?
(A) -3 and 3 (B) -1 and 1 (C) -1 and 3 (D) 1 and 3
GATE 2018 General Aptitude (GA) Set-1
GA 2/2
Q.7 Given that ?? and ?? are integers and ?? + ?? 2
?? 3
is odd, which one of the following
statements is correct?
(A) ?? and ?? are both odd (B) ?? and ?? are both even
(C) ?? is even and ?? is odd (D) ?? is odd and ?? is even
Q.8 From the time the front of a train enters a platform, it takes 25 seconds for the back of the
train to leave the platform, while travelling at a constant speed of 54 km/h. At the same
speed, it takes 14 seconds to pass a man running at 9 km/h in the same direction as the
train. What is the length of the train and that of the platform in meters, respectively?
(A) 210 and 140 (B) 162.5 and 187.5
(C) 245 and 130 (D) 175 and 200
Q.9 Which of the following functions describe the graph shown in the below figure?
(A) ?? = ||?? | + 1| ? 2 (B) ?? = ||?? | ? 1| ? 1
(C) ?? = ||?? | + 1| ? 1 (D) ?? = ||?? ? 1| ? 1|
Q.10 Consider the following three statements:
(i) Some roses are red.
(ii) All red flowers fade quickly.
(iii) Some roses fade quickly.
Which of the following statements can be logically inferred from the above statements?
(A) If (i) is true and (ii) is false, then (iii) is false.
(B) If (i) is true and (ii) is false, then (iii) is true.
(C) If (i) and (ii) are true, then (iii) is true.
(D) If (i) and (ii) are false, then (iii) is false.
END OF THE QUESTION PAPER
GATE 2018 Petroleum Engineering
PE 1/17
Q. 1 ? Q. 25 carry one mark each.
Q.1 The Taylor series expansion of the function,
?? (?? ) =
?1
1+?? ,
around ?? = 0 (up to 4
th
order term) is:
(A) 1 + ?? + ?? 2
+ ?? 3
+ ?? 4
(B) ?1 + ?? ? ?? 2
+ ?? 3
? ?? 4
(C) ?1 ? ?? + ?? 2
? ?? 3
+ ?? 4
(D) ?1 + ?? ? 2?? 2
+ 3?? 3
? 4?? 4
Q.2
The inverse of the matrix [
1 3
1 2
] is,
(A) [
2 3
1 1
] (B) [
?2 1
3 ?1
] (C) [
?2 3
1 ?1
] (D) [
2 ?3
?1 1
]
Q.3 The line integral of a vector function ?? ?
(?? ? ) over a curve C in a simply connected domain D
in space, is defined by:
? ?? ?
(?? ? ). ?? ?? ?
?? = ? (?? 1
???? + ?? 2
???? + ?? 3
???? )
??
The line integral is independent of path in D. ?? 1
, ?? 2
, and ?? 3
are continuous, and have
continuous first partial derivatives in D. ?? ?
is a closed curve in D.
Which one of the following is NOT ALWAYS true in domain D?
(A) ?
?
? ?? ?
= 0
?
(B) ?
?
. ?? ?
= 0
(C) ? ?? ?
(?? ? ). ?? ?? ?
?? ?
= 0
(D) ?? ?
? ?? ?
= 0
?
Q.4 Which one of the following is the integrating factor (IF) for the differential equation,
(cos
2
?? )
????
????
+ ?? = cos?? ?
(A) ?? tan ?? (B) ?? cos ??
(C) ?? ? tan ?? (D) ?? sin ??
GATE 2018 Petroleum Engineering
PE 2/17
Q.5 A phase diagram of a black oil is shown in the figure (Y is the critical point).
Match the following:
(P) Curve XY (I) Dew point curve
(Q) Curve YZ (II) Single phase liquid
(R) Phase I (III) Bubble point curve
(S) Phase II (IV) Single phase gas
(A) P-I, Q-III, R-II, S-IV (B) P-III, Q-I, R-II, S-IV
(C) P-III, Q-I, R-IV, S-II (D) P-I, Q-II, R-III, S-IV
Q.6 Match the following chemicals to their respective oilfield applications:
(P) Hydrate inhibitor (I) Formaldehyde
(Q) Well stimulation (II) Xanthan gum
(R) Drilling fluid biocide (III) Methanol
(S) Viscosifier (IV) Hydrochloric acid
(A) P-IV, Q-III, R-II, S-I (B) P-III, Q-I, R-IV, S-II
(C) P-I, Q-III R-IV, S-II (D) P-III, Q-IV, R-I, S-II
GATE 2018 Petroleum Engineering
PE 3/17
Q.7 The CH4-hydrate equilibrium curve (dashed) and CO2-hydrate equilibrium curve (solid) on
a pressure-temperature plane above 0?C are shown in the figure. The two curves divide the
plane in four non-overlapping regions. In which region are CO2-hydrates stable and CH4-
hydrates unstable?
(A) I (B) II (C) III (D) IV
Q.8 Plot of ratio of pressure to gas compressibility factor (P/Z) vs. cumulative gas production
(Gp) for a gas reservoir (represented by solid curve in the figure) was shown to a reservoir
engineering student.
The student made the following statements:
(I) A water aquifer is attached to this gas reservoir.
(II) P/Z vs. Gp curve must always be a straight line for water encroachment in a gas
reservoir.
(III) The ultimate gas recovery is diminished due to water encroachment.
Which of the above statements are TRUE?
(A) Only I and II (B) Only II and III (C) Only I and III (D) I, II, and III
Q.9 Waste water from oil industry consists of oil in free and emulsified forms. The oil in the
free form can be recovered by:
(A) Aerated lagoons
(B) Trickling filters
(C) Gravity separators
(D) Biological oxygen pond
P/Z
G p
GATE 2018 Petroleum Engineering
PE 4/17
Q.10 A reservoir model consisting of two porous matrices M and N, separated by a fracture, is
shown in the figure. The matrices are strongly water-wet and are saturated with oil of
specific gravity 0.8. Water is injected only in the fracture at injection well A. If the
Reynolds number for the flow in the fracture conduit is assumed to be less than unity, which
one of the following force will dominate oil recovery from the porous matrix M during the
water-flood operation?
(A) Capillary force (B) Gravity force
(C) Viscous force (D) Inertial force
Q.11 A fractional flow curve is given for a core for which the irreducible water saturation is 0.2
and the residual oil saturation is 0.3. The initial water saturation in the core is 0.3. If
Welge?s method is applied to find the breakthrough saturation and fraction flow of water at
breakthrough, which point should be used in the figure to draw a tangent line to the
fractional flow curve.
(A) I (B) II (C) III (D) IV
Injection well A Production well B
Matrix M
Matrix N
Fracture
GATE 2018 Petroleum Engineering
PE 5/17
Q.12 Which one of the following curves represents behavior of oil phase viscosity as a function
of pressure in the reservoir (where, Pb is the bubble point pressure of oil)?
(A) Curve I (B) Curve II (C) Curve III (D) Curve IV
Q.13 Pick out the INCORRECT statement.
(A) Flash point is always lower than fire point.
(B) Pour point of lube oil can be reduced by removing the wax from it.
(C) Fracturing is a well stimulation technique.
(D) Coal bed methane typically contains more than 60% CO2.
Q.14 Which one of the following phenomena encountered during flooding is desirable for
increasing oil recovery from a reservoir?
(A) Viscous fingering (B) Formation damage
(C) Increase in mobility ratio (D) Decrease in capillary pressure
Q.15 CO2 foams are used for enhanced oil recovery due to which of the following reasons?
(I) It can be used for CO2 sequestration
(II) CO2 can exist in the form of a dense fluid at reservoir conditions
(III) CO2 can convert to hydrocarbon at the reservoir temperature and pressure
(IV) Solubility of CO2 in oil is higher compared to gases like N2
(A) Only I, II, and III (B) Only I, II, and IV
(C) Only II, III, and IV (D) Only I, III, and IV
GATE 2018 Petroleum Engineering
PE 6/17
Q.16 Which one of the following is FALSE about a typical offshore deepwater oil spill?
(A) Using boom boats to prevent spilled oil from spreading
(B) Allowing the spill to reach the shore before clearing
(C) Burning of spilled oil
(D) Using a skimmer to collect the oil
Q.17 Which one of these methods is NOT commonly used to deal with the problem of soil
contamination by oil spillage?
(A) Biodegradation
(B) Leaching out the oil
(C) Soil recycling
(D) Using rain water to wash the contaminants
Q.18 The factor on which the selection of an offshore platform for the reservoir does NOT
depend:
(A) Water depth
(B) Reservoir fluid properties
(C) Sea bed conditions
(D) Best case weather forecast
Q.19 Which one of the following options is correct about the effects of steam stimulation in
increasing the oil production rate?
(I) Reduces the oil viscosity
(II) Increases the formation damage
(III) Reduces the interfacial tension
(IV) Increases the oil viscosity
(A) Only I and II
(B) Only II and III
(C) Only III and IV
(D) Only I and III
Q.20 Which one of the following is INCORRECT about oil based drilling muds?
(A) Good rheological properties at higher temperatures (as high as 250
o
C)
(B) Effective against corrosion
(C) Detection of gas kick is difficult
(D) Less inhibitive than water based muds
Q.21 Assume that viscous, gravity, and capillary are the only dominant forces for fluid flow in a
given reservoir, a cone formed around the perforation zone will break into the well, when
(A) capillary forces are more than viscous and gravity forces.
(B) viscous forces are more than gravity forces.
(C) gravity forces are more than capillary forces.
(D) viscous and gravity forces are equal.
GATE 2018 Petroleum Engineering
PE 7/17
Q.22
Two complex numbers, ?? ?
and ?? ? are related as follows:
?? ?
=
?? ?
????
where, ?? = ??1 and ?? is a scalar. Given principal argument of ?? ? , Arg (?? ? ) = ?
2?? 3
, the
principal argument of ?? ?
, Arg(?? ?
) =______________. (rounded-off to two decimal places.
Use ?? = 3.14)
Q.23 A cylindrical sandstone core, 7.5 cm long and 3.5 cm diameter has grain density of
3 g/cm
3
. If the mass of the dry core is 200 g, the porosity of the core is __________%.
(rounded-off to two decimal places)
Q.24 In an oil reservoir the current average pressure is below bubble point pressure of the oil.
The current oil production rate is 10
3
m
3
/day and total gas production rate is 10
5
m
3
/day at
STP conditions (25?C and 1 atm). The formation volume factor of the oil is
1.2
m
3
at reservoir pressure
m
3
at STP
and that of gas is 0.01
m
3
at reservoir pressure
m
3
at STP
. The
dissolved gas oil ratio is 10
m
3
of gas at STP
m
3
of oil at STP
of oil.
The gas flow rate at bottom-hole conditions is ______? 10
2
m
3
per day. (rounded-off to
two decimal places)
Q.25 Exponential decline curve is to be used to estimate the oil reserves of a well. The current
oil production rate is 1000 m
3
per day and yearly decline rate is 6% per year. If the
minimum oil flow rate economically sustainable for the well is 1 m
3
per day, the reserves
(economically producible) associated with the well are _____ ? 10
6
m
3
. (rounded-off to
two decimal places. Use 1 year = 365 days)
GATE 2018 Petroleum Engineering
PE 8/17
Q. 26 ? Q. 55 carry two marks each.
Q.26 The probability density for three binomial distributions (D1, D2, and D3) is plotted against
number of successful trials in the given figure.
Each of the plotted distributions corresponds to a unique pair of (n, p) values, where, n is
the number of trials and p is the probability of success in a trial. Three sets of (n, p) values
are provided in the table.
Set (n, p)
I (60, 0.3)
II (60, 0.2)
III (24, 0.5)
Pick the correct match between the (n, p) set and the plotted distribution.
(A) Set I ? D1, Set II ? D2, Set III ? D3
(B) Set I ? D3, Set II ? D1, Set III ? D2
(C) Set I ? D2, Set II ? D3, Set III ? D1
(D) Set I ? D2, Set II ? D1, Set III ? D3
Q.27 Which of the following statements are true about Natural Gas Hydrates?
Natural gas hydrates:
(I) are formed under low temperature and high pressure.
(II) can store approximately 160 m
3
of gas per m
3
of hydrate at 25
o
C and 1 atm.
(III) formation is an endothermic process.
(IV) are potential sources of methane.
(A) Only II, III & IV (B) Only I, II & III
(C) Only I, II & IV (D) Only I, III & IV
0
0.05
0.1
0.15
0 10 20 30
Probability density
Number of successful trials
D1
D2
D3
GATE 2018 Petroleum Engineering
PE 9/17
Q.28 P wf (bottom-hole well flowing pressure) vs. Q (flow rate) plots show the inflow
performance relation (IPR) and vertical lift performance (VLP) curves. Figure I shows
VLP curves for two well head pressures Phw1 and Phw2. Figure II shows VLP curves for two
well diameters D1 and D2. Which one of the following statements is true?
(A) Phw1 > Phw2 and D1 < D2 (B) Phw1 > Phw2 and D1 > D2
(C) Phw1 < Phw2 and D1 < D2 (D) Phw1 < Phw2 and D1 > D2
Q.29 Match the following:
(P) Weber Number (I) Ratio of inertial force to viscous force
(Q) Froude Number (II) Ratio of convective heat transfer to conductive heat
transfer
(R) Reynolds number (III) Ratio of inertial force to interfacial force
(S) Nusselt number (IV) Ratio of inertial force to gravitational force
(A) P-III, Q-IV, R-I, S-II (B) P-III, Q-II, R-I, S-IV
(C) P-II, Q-III, R-IV, S-I (D) P-IV, Q-III, R-I, S-II
Q.30 A dilute mixture of coal and sand particles, both of diameter 100 ?m and densities
1800 kg/m
3
and 2600 kg/m
3
, respectively, is to be classified by elutriation technique using
water (density 1000 kg/m
3
, viscosity 10
-3
Pa.s). Assuming Stokes law is applicable, the
minimum settling velocity of the particles in the mixture is (g = 9.81 m/s
2
):
(A) 4.36 ? 10
-3
m/s (B) 8.72 ? 10
-3
m/s
(C) 2.18 ? 10
-3
m/s (D) 1.29 ? 10
-3
m/s
GATE 2018 Petroleum Engineering
PE 10/17
Q.31 Oil flow rate and flowing bottom-hole pressure (FBHP) recorded with time during a multi-
rate well test are shown.
Let k is the reservoir permeability, h is the formation thickness and ? is the viscosity of the
oil. ??? ?? (?? ) is constant-rate dimensionless pressure drop as a function of time. The total
pressure drop till time, t, where t > t1, will be:
(A)
?? 1
?? 2???? ?
??? ?? (?? ) +
(?? 2
??? 1
)?? 2???? ?
??? ?? (?? ? ?? 1
)
(B)
?? 1
?? 2???? ?
??? ?? (?? 1
) +
(?? 2
??? 1
)?? 2???? ?
??? ?? (?? ? ?? 1
)
(C)
?? 1
?? 2???? ?
??? ?? (?? ) +
?? 2
?? 2???? ?
??? ?? (?? ? ?? 1
)
(D)
?? 1
?? 2???? ?
??? ?? (?? 1
) +
?? 2
?? 2???? ?
??? ?? (?? )
Q.32 Which one of the following options presents the correct combination?
(P) Reservoir limit test (I) Communication between wells
(Q) Modified isochronal test (II) Ideally zero flowing bottom hole pressure
(R) Interference test (III) Extended drawdown test
(S) Absolute open flow potential (IV) Drawdown and build-up test of equal duration
(A) P-II, Q-III, R-I, S-IV (B) P-IV, Q-I, R-III, S-II
(C) P-III, Q-IV, R-I, S-II (D) P-I, Q-III, R-IV, S-II
GATE 2018 Petroleum Engineering
PE 11/17
Q.33 Which one of the following options presents the correct combination?
(P) Roller Cone bits (I) Long and widely spaced teeth
(Q) PDC bits (II) Journal (Pin) angle
(R) Soft formation (III) Short and wider teeth
(S) Hard formation (IV) Size of the cutting
(T) Back rake angle (V) 1400
o
C and 6x10
5
psi
(A) P-II, Q-V, R-I, S-III, T-IV
(B) P-III, Q-IV, R-I, S-II, T-V
(C) P-III, Q-II, R-IV, S-I, T-V
(D) P-II, Q-V, R-III, S-I, T-IV
Q.34 Primary and secondary indicators of kick in a well where the indicators are:
1) flow rate increase,
2) gas, oil or water-cut muds,
3) pit volume increase,
4) flowing well with mud pump shut-off,
5) reduction in drill-pipe weight,
6) drilling break.
Which one of the following presents the correct combination?
(A) Primary (1, 3, 5) and Secondary (2, 4, 6)
(B) Primary (1, 2, 3) and Secondary (4, 5, 6)
(C) Primary (1, 2, 4) and Secondary (3, 5, 6)
(D) Primary (1, 3, 4) and Secondary (2, 5, 6)
GATE 2018 Petroleum Engineering
PE 12/17
Q.35 Relative permeability curve for the two rock types (X: solid line and Y: dashed line) are
shown in the diagram, where Sw is the fractional water saturation. Which one of the
following statements is correct about wettability and consolidated nature of the two rock
types?
(A) X is more consolidated and mixed wet, Y is less consolidated and water wet
(B) X is more consolidated and water wet, Y is less consolidated and mixed wet
(C) X is less consolidated and mixed wet, Y is more consolidated and water wet
(D) X is less consolidated and water wet, Y is more consolidated and mixed wet
Q.36 Which one of the following options presents correct combinations of exploration methods
with their respective frequency of operation?
(P) Seismic (I) ~10
6
Hz
(Q) Sonic (II) ~10
2
Hz
(R) Controlled Source EM (III) ~10
4
Hz
(S) Ultrasonic (IV) ~1 Hz
(A) P-IV, Q-II, R-I, S-III
(B) P-II, Q-III, R-IV, S-I
(C) P-II, Q-I, R-IV, S-III
(D) P-IV, Q-I, R-II, S-III
GATE 2018 Petroleum Engineering
PE 13/17
Q.37 Which one of the following options presents the correct combinations?
(P) Borisov?s (I) Critical rate correlation in vertical wells with coning
(Q) Schols? (II) Horizontal well performance relation
(R) Efros? (III) Vertical well performance relation
(S) Wiggins? (IV) Critical rate correlation in horizontal wells with coning
(A) P-II, Q-IV, R-I, S-III
(B) P-IV, Q-III, R-II, S-I
(C) P-IV, Q-II, R-III, S-I
(D) P-II, Q-I, R-IV, S-III
Q.38 Which one of the following options represents the typical sequence of applying cut-offs for
pay zone identification in a conventional reservoir?
(A) porosity, saturation, shale
(B) porosity, permeability, saturation
(C) shale, porosity, saturation
(D) shale, porosity, permeability
Q.39 Which one of the following options represents the correct sequence of arrival of acoustic
wave energy recorded in a sonic log?
(A) shear, surface, compressional
(B) compressional, shear, surface
(C) surface, shear, compressional
(D) compressional, surface, shear
Q.40 The variation of the amount of salt in a tank with time is given by,
????
????
+ 0.025?? = 20 ,
where, ?? is the amount of salt in kg and ?? is the time in minutes. Given that there is no salt
in the tank initially, the time at which the amount of salt increases to 200 kg is __________
minutes. (rounded-off to two decimal places)
Q.41 Solve the given differential equation using the 2
nd
order Runge-Kutta (RK2) method:
???? ???? = ?? ? ??? ; Initial condition : ?? (?? = 0) = 4
Use the following form of RK2 method with an integration step-size, ? = 0.5:
?? 1
= ?? (?? ?? , ?? ?? ) ; ?? 2
= ?? (?? ?? + 0.5?, ?? ?? + 0.5?? 1
?)
?? ?? +1
= ?? ?? + ?? 2
?
The value of ?? (?? = 0.5) =__________________. (rounded-off to two decimal places)
GATE 2018 Petroleum Engineering
PE 14/17
Q.42 A box contains 100 balls of same size, of which, 25 are black and 75 are white. Out of 25
black balls, 5 have a red dot. A trial consists of randomly picking a ball and putting it back
in the same box, i.e., sampling is done with replacement. Two such trials are done.
The conditional probability that no black ball with a red dot is picked given that at least
one black ball is picked, is __________. (in fraction rounded-off to two decimal places)
Q.43 A cylindrical pipeline of length 30 km is transporting naphtha. Pressure sensors are
attached along pipe length to detect leaks. Under steady-state, leak-free operation, there is a
linear pressure drop along the length (z) of the pipeline. If a leak occurs, the pressure
profile develops a kink at the leak point ?? leak
.
Assume that there is only one leak-point (4 km < ?? leak
< 27 km ) and a new steady-state is
reached. The steady-state pressure measurements at four locations along the pipe-length are
provided in the table. The location of the leak-point using the gradient intersection method
is _______________km. (rounded-off to two decimal places)
?? (km) Pressure
0 ?? 0
4 0.84?? 0
27 0.31?? 0
30 0.25?? 0
GATE 2018 Petroleum Engineering
PE 15/17
Q.44 A dry core was subjected to the mercury injection test in the laboratory. Following are the
related details:
Average formation porosity = 0.2
Formation volume factor, BO = 1.2 reservoir-bbl/STB
Oil API
o
= 32, Specific gravity of water = 1.1
Hydrostatic gradient = 0.433 psi/ft
(?? ????
cos?? )
res
= 26 dyne/cm, where ?? ????
is the oil-water interfacial tension and ?? is the
contact angle
(?? ????
cos?? )
lab
= 367 dyne/cm, where ?? ????
is air- mercury interfacial tension and ?? is the
contact angle
Average drainage area = 80 acres
(1 acre-ft = 7758 bbl)
The Table shows the laboratory data for capillary pressure at different mercury saturations.
Pc (psia) Mercury saturation (SHg)
10 0.0075
17 0.25
30 0.50
108 0.70
2000 0.85
?? ?? =
2?? cos ??
?? and the average water saturation (?? ?? ) for the productive column is 0.25. The
Original Oil in Place (OOIP) in the productive column where ?? ?? ? 0.5 is ___________
MMSTB. (rounded-off to one decimal place)
Q.45 A well is drilled with water based mud. The water saturation in the completely flushed
zone (no formation fluid residual) is given by,
?? ????
= (
??
?
2
?
?? ????
?? ????
)
1/2
,
where, Rmf and Rxo are the mud filtrate resistivity and flushed zone resistivity, respectively.
Use, a = 1.0 and Rxo = 25 Rmf.
The calculated porosity (?) of the formation is ______. (in fraction rounded-off to two
decimal places)
Q.46 An oil well is tested at a flow rate (Q) of 50 BOPD. The bottom hole flowing pressure (Pwf)
is 500 psia. The shut-in pressure is 1000 psia. If Pwf is lowered to 300 psia and assuming
the Vogel?s correlation holds, the estimated flow rate in the oil well is ______BOPD
(rounded-off to two decimal places). The Vogel?s correlation is:
?? ?? ??????
= 1 ? 0.2 (
?? ????
?? ?
) ? 0.8 (
?? ????
?? ?
)
2
GATE 2018 Petroleum Engineering
PE 16/17
Q.47 Using Miller, Dyes and Hutchinson (MDH) method, the skin factor of an oil well is found
to be ?? = ? 3.5.
The reservoir and fluid properties are:
Formation porosity is 0.20
Total compressibility is 2.5 ? 10
-5
psia
-1
Oil viscosity is 1.5 cP
Wellbore radius is 0.5 ft
Flowing bottom hole pressure at ?t = 0 is 2830 psia
Shut in pressure at ?t = 1 hr (P?t=1hr) is 3000 psia
Slope of middle time region (MTR) line in MDH plot is 190 psia/cycle.
The permeability of the reservoir is __________mD. (rounded-off to two decimal places)
Q.48 An oil well (producing under expansion drive only) in a reservoir is subjected to two
pressure build-up tests. The average formation thickness of the reservoir is 13 ft, the total
compressibility is 1?10
-5
psia
-1
, and porosity is 0.2. The average formation volume factor
of oil is 1.3 reservoir-bbl/STB. Average reservoir pressure during the first test and the
second test was found to be 3500 psia and 3200 psia, respectively.
If the oil produced between the two pressure build-up tests in 180 days is 250 STB/day, the
area of the reservoir is __________acres. (rounded-off to two decimal places)
(Use: 1 acre = 43560 ft
2
, 1 bbl = 5.615 ft
3
)
Q.49 A well in a very large reservoir has a wellbore radius of 10 cm. The sandstone, with a
porosity of 0.25 and 12% (by grain volume) calcite (CaCO3), is to be acidized with a
preflush (HCl solution) so as to dissolve all the calcite upto a distance of 1 m from the
wellbore. 1 m
3
of preflush is able to dissolve 0.082 m
3
CaCO3. Assume that the reaction
between HCl and CaCO3 is instantaneous.
The minimum preflush volume required per meter of the formation thickness is
______________m
3
. (rounded-off to two decimal places)
Q.50 At a particular temperature, the vapour pressure of benzene and toluene are 4 atm and
1.2 atm, respectively. The composition of the liquid at equilibrium is 0.5 moles of benzene
and 0.5 moles of toluene. Assuming ideal gas and ideal solution, the equilibrium vapour
phase mole fraction of benzene is ________ . (rounded-off to two decimal places)
Q.51 Saturated steam at 0.7 atm and 90?C condenses on a vertical pipe of 2 cm outside diameter
and 40 cm length. The average condensation heat transfer coefficient on the tube is
12000 W/m
2
K. The outside surface temperature of the pipe is maintained constant at 85?C.
The enthalpy values for saturated steam and condensate are 2660 kJ/kg and 375 kJ/kg,
respectively. The rate of steam condensation is ____ kg/h. (rounded-off to two decimal
places)
GATE 2018 Petroleum Engineering
PE 17/17
Q.52 Oil is being transported between two reservoirs with the help of three parallel pipes at
steady state. The diameters of these pipes are 2 cm, 3 cm and 4 cm, respectively. The pipes
are equal in length and the flow is laminar. The discharge through the 4 cm diameter pipe is
50 liters/s. The discharge through the 2 cm diameter pipe is _____ liters/s. (rounded-off to
two decimal places)
Q.53 A driller finds an oil reservoir with a gas cap starting at a depth of 1000 m from the surface.
The gas-oil contact was found at 1100 m depth and water-oil contact was found at 1300 m
depth. The water pressure in the aquifer below the oil zone varies with depth from the
surface (h, in meters) as, P = h?10
4
Pa. The density of the oil is 900 kg/m
3
and that of the
gas is 5 kg/m
3
at the reservoir condition. The minimum density of the mud needed to stop
the gas kick when the driller reaches at the top of the gas cap is _____kg/m
3
. (rounded-off
to two decimal places. Use g = 9.81 m/s
2
)
Q.54 The viscosity, ? (in Pa.s) of a power law fluid as a function of shear rate, ?? ? (in s
-1
) is given
by the following relation:
?? =
1
2
|?? ?|
This power law fluid lies between two infinitely large horizontal parallel plates separated
by a distance (h) of 10
-3
m. The top plate is moving horizontally at a velocity (v) of
10
-3
m/s and the bottom plate is held stationary. Assuming laminar flow and neglecting
gravity, the absolute value of steady-state shear stress acting on the bottom plate
is ______ Pa. (rounded-off to two decimal places)
Q.55 A heterogeneous rectangular rock of cross-sectional area 1 m
2
perpendicular to the flow is
being flooded by water to measure the effective permeability from cross-section AA? to
cross-section CC?.
The pressure at the cross-sections AA?, BB?, and CC? is 2 bar, 1.5 bar, and 1 bar,
respectively. The permeability in mili-Darcy and lengths AB and BC in meters are given in
the figure. The effective permeability of the rock from AA? to CC? is ______mD.
(rounded-off to two decimal places)
END OF THE QUESTION PAPER
A
B C
2 m 3 m
1 m
1 m
1 mD 3 mD
2 mD 4 mD
A?
B?
C?
Flow direction
FirstRanker.com - FirstRanker's Choice
This post was last modified on 18 December 2019