Download PTU (I.K. Gujral Punjab Technical University Jalandhar (IKGPTU) ) BE/BTech ECE (Electronics And Communications Engineering) 2020 March 1st and 2nd Sem ME 102 Engineering Drawing Previous Question Paper
Roll No. Total No. of Pages : 03
Total No. of Questions : 18
B.Tech. (ECE/ME/IT/CSE) (Sem.?1,2)
ENGINEERING DRAWING
Subject Code : ME-102
M.Code : 54013
Time : 3 Hrs. Max. Marks : 60
INSTRUCTIONS TO CANDIDATES :
1. SECTION-A is COMPULSORY consisting of TEN questions carrying TWO marks
each.
2. SECTION - B & C. have FOUR questions each.
3. Attempt any FIVE questions from SECTION B & C carrying EIGHT marks each.
4. Select atleast TWO questions from SECTION - B & C.
SECTION-A
Write short notes on :
1) What do you understand by horizontal trace of a line?
2) Draw the symbol of first angle projection system.
3) What do you mean by single stroke letters?
4) Draw any two types of lines and give their applications.
5) What is the meaning of apparent inclination of a straight line?
6) What is a representative fraction?
7) Draw the projections of a point P which is 20 mm below HP and 30 mm behind VP.
8) What are principal planes?
9) Show the development of a right circular cone with neat freehand sketch.
10) Draw the plan and elevation of a 50 mm long line AB which is in VP and inclined to HP
at 60?.
SECTION-B
11) Construct a diagonal scale of representative fraction 1/400. It should be long enough to
measure 60 metres. Mark a distance of 58.6 metres on this scale.
FirstRanker.com - FirstRanker's Choice
1 | M-54013 (S1)-2741
Roll No. Total No. of Pages : 03
Total No. of Questions : 18
B.Tech. (ECE/ME/IT/CSE) (Sem.?1,2)
ENGINEERING DRAWING
Subject Code : ME-102
M.Code : 54013
Time : 3 Hrs. Max. Marks : 60
INSTRUCTIONS TO CANDIDATES :
1. SECTION-A is COMPULSORY consisting of TEN questions carrying TWO marks
each.
2. SECTION - B & C. have FOUR questions each.
3. Attempt any FIVE questions from SECTION B & C carrying EIGHT marks each.
4. Select atleast TWO questions from SECTION - B & C.
SECTION-A
Write short notes on :
1) What do you understand by horizontal trace of a line?
2) Draw the symbol of first angle projection system.
3) What do you mean by single stroke letters?
4) Draw any two types of lines and give their applications.
5) What is the meaning of apparent inclination of a straight line?
6) What is a representative fraction?
7) Draw the projections of a point P which is 20 mm below HP and 30 mm behind VP.
8) What are principal planes?
9) Show the development of a right circular cone with neat freehand sketch.
10) Draw the plan and elevation of a 50 mm long line AB which is in VP and inclined to HP
at 60?.
SECTION-B
11) Construct a diagonal scale of representative fraction 1/400. It should be long enough to
measure 60 metres. Mark a distance of 58.6 metres on this scale.
2 | M-54013 (S1)-2741
12) The distance between end projectors of a straight line AB is 40 mm. End A is 40 mm
behind VP and 20 mm below HP and end B is 6 mm behind VP. The line is inclined at
30? to the VP. Draw the projections of line and show its VT and HT. Also find out the
true length of the line and ?.
13) A pentagonal prism of base side 40 mm and height 70 mm has a circular hole of diameter
36 mm running centrally through it along the axis. Draw its projections when one of its
base corners is in HP and the longer edge through that corner makes an angle of 45? with
HP.
14) A right regular hexagonal pyramid, side of the base 40 mm and axis 80 mm long is lying
on one of its triangular faces on HP with the axis parallel to VP. A vertical sectional
plane inclined at 45? to VP cuts through the centre of the base, the apex being retained.
Draw the top view and sectional front view.
SECTION-C
15) Two orthographic views of an object are shown in Figure 1 below. Draw its isometric
view.
FIG.1
16) The axis of an oblique regular hexagonal pyramid, base edge 30 mm and height 60 mm,
is inclined to the vertical at an angle of 30?. Develop the lateral surfaces of the solid.
FirstRanker.com - FirstRanker's Choice
1 | M-54013 (S1)-2741
Roll No. Total No. of Pages : 03
Total No. of Questions : 18
B.Tech. (ECE/ME/IT/CSE) (Sem.?1,2)
ENGINEERING DRAWING
Subject Code : ME-102
M.Code : 54013
Time : 3 Hrs. Max. Marks : 60
INSTRUCTIONS TO CANDIDATES :
1. SECTION-A is COMPULSORY consisting of TEN questions carrying TWO marks
each.
2. SECTION - B & C. have FOUR questions each.
3. Attempt any FIVE questions from SECTION B & C carrying EIGHT marks each.
4. Select atleast TWO questions from SECTION - B & C.
SECTION-A
Write short notes on :
1) What do you understand by horizontal trace of a line?
2) Draw the symbol of first angle projection system.
3) What do you mean by single stroke letters?
4) Draw any two types of lines and give their applications.
5) What is the meaning of apparent inclination of a straight line?
6) What is a representative fraction?
7) Draw the projections of a point P which is 20 mm below HP and 30 mm behind VP.
8) What are principal planes?
9) Show the development of a right circular cone with neat freehand sketch.
10) Draw the plan and elevation of a 50 mm long line AB which is in VP and inclined to HP
at 60?.
SECTION-B
11) Construct a diagonal scale of representative fraction 1/400. It should be long enough to
measure 60 metres. Mark a distance of 58.6 metres on this scale.
2 | M-54013 (S1)-2741
12) The distance between end projectors of a straight line AB is 40 mm. End A is 40 mm
behind VP and 20 mm below HP and end B is 6 mm behind VP. The line is inclined at
30? to the VP. Draw the projections of line and show its VT and HT. Also find out the
true length of the line and ?.
13) A pentagonal prism of base side 40 mm and height 70 mm has a circular hole of diameter
36 mm running centrally through it along the axis. Draw its projections when one of its
base corners is in HP and the longer edge through that corner makes an angle of 45? with
HP.
14) A right regular hexagonal pyramid, side of the base 40 mm and axis 80 mm long is lying
on one of its triangular faces on HP with the axis parallel to VP. A vertical sectional
plane inclined at 45? to VP cuts through the centre of the base, the apex being retained.
Draw the top view and sectional front view.
SECTION-C
15) Two orthographic views of an object are shown in Figure 1 below. Draw its isometric
view.
FIG.1
16) The axis of an oblique regular hexagonal pyramid, base edge 30 mm and height 60 mm,
is inclined to the vertical at an angle of 30?. Develop the lateral surfaces of the solid.
3 | M-54013 (S1)-2741
17) Figure 2 below shows the pictorial view of a wall bracket. Draw its front view as seen
from the direction ?A? and the top view.
FIG.2
18) A square prism, edge of the base 30 mm and height 60 mm is resting on its base on HP. It
is completely penetrated by a horizontal square pyramid of 30 mm base edge and height
60 mm such that their axes bisect each other at right angles. The base edges of the two
solids are equally inclined to VP. Draw the projections of the solids showing lines of
intersection.
NOTE : Disclosure of Identity by writing Mobile No. or Making of passing request on any
page of Answer Sheet will lead to UMC against the Student.
FirstRanker.com - FirstRanker's Choice
This post was last modified on 21 March 2020