o_
CO
0
? ?
--- Content provided by FirstRanker.com ---
tf) .0?
C ^
G
kr
--- Content provided by FirstRanker.com ---
,I I 0 0
E
--- Content provided by FirstRanker.com ---
ti2 0
_c
o
C
--- Content provided by FirstRanker.com ---
=, 0?
C.) I
,
--- Content provided by FirstRanker.com ---
1C
0 '17
CO
"
--- Content provided by FirstRanker.com ---
CS?t 0
0
? ? 0
..4%-
--- Content provided by FirstRanker.com ---
= ? -0
? c
a) ?
`
--- Content provided by FirstRanker.com ---
71E
0
0
--- Content provided by FirstRanker.com ---
. .("s1
? ?
0
CO
--- Content provided by FirstRanker.com ---
zt
0
--- Content provided by FirstRanker.com ---
0.E
Fourth Semester B.E. Degree Examination, Dec.2019/Jan.2020
Mechanical Measurements and Metrology
Time: 3 hrs. Max. Marks: 100
--- Content provided by FirstRanker.com ---
Note: Answer ant' FIVE fall questions, choosing ONE full question from each module.Module-1
1 a. Define Metrology. What are the objectives of metrology? (06 Marks)
b. Differentiate line and end standards with examples. (06 Marks)
c. Four length bars A, B, C, D of approximately 250mm each are to be calibrated with standard
--- Content provided by FirstRanker.com ---
calibrated metre bar which is actually 0.0008mm less than a metre. It is also found that, bar`B' is 0.0002mm longer than bar 'A', bar 'C' is 0.0004mm longer than bar 'A' and bar '13"
is 0.0001mm shorter than bar 'A'. The length of all four bars put together is 0.0003mm
longer than the calibrated standard metre. Determine the actual dimensions of each bar.
(08 Marks)
--- Content provided by FirstRanker.com ---
OR2 a. Explain with neat sketches wringing phenomena of slip gauges. (06 Marks)
b. Build the following lengths by using M-112 set of slip gauges and write their combinations:
i) 29.875mm ii) 101.345mm iii) 78.3665mm (09 Marks)
c. Explain with neat sketches how a sine bar can be used to measure an unknown angle.
--- Content provided by FirstRanker.com ---
(05 Marks)3 a. Define tolerance with types.
b. Define fit. Explain different types of fits with sketches.
c. Discuss hole and shaft basic system with neat sketches.
OR
--- Content provided by FirstRanker.com ---
4 a. List essential considerations and materials used for construction of gauges. (04 Marks)b.
Determine the tolerances on the hole and the shaft for a precision running fit designated by
501-17g6. Given:
i) 50mm lies between 30-50 mm
--- Content provided by FirstRanker.com ---
ii) i(Microns) = 0.45 (D)" + 0.001Diii) Fundamental deviation for, H = 0
iv) Fundamental deviation for "g" shaft = -2.5D
?34
.
--- Content provided by FirstRanker.com ---
v) ITS = 16i and IT6 = 10i (08 Marks)c. Explain with neat sketches double ended plug and snap gauges. (08 Marks)
Module-3
5 a. Explain terminology of screw thread. (06 Marks)
b. Derive an equation for measuring effective diameter of screw thread by using 2-wire
--- Content provided by FirstRanker.com ---
method. (08 Marks)c. With neat sketch, explain tool Maker's microscope. (06 Marks)
(06 Marks)
(08 Marks)
(06 Marks)
--- Content provided by FirstRanker.com ---
1 of 2FirstRanker.com - FirstRanker's Choice
171446B/17MEB406
USN
CO
--- Content provided by FirstRanker.com ---
tio_
CO
--- Content provided by FirstRanker.com ---
0? ?
tf) .0
?
C ^
--- Content provided by FirstRanker.com ---
Gkr
,
I I 0 0
--- Content provided by FirstRanker.com ---
E
ti
2 0
_c
--- Content provided by FirstRanker.com ---
oC
=, 0
?
C.) I
--- Content provided by FirstRanker.com ---
,1
C
0 '17
--- Content provided by FirstRanker.com ---
CO"
CS
?t 0
0
--- Content provided by FirstRanker.com ---
? ? 0..4%-
= ? -
0
? c
--- Content provided by FirstRanker.com ---
a) ?`
71
E
--- Content provided by FirstRanker.com ---
00
. .
("s1
? ?
--- Content provided by FirstRanker.com ---
0CO
z
--- Content provided by FirstRanker.com ---
t0
0.
E
Fourth Semester B.E. Degree Examination, Dec.2019/Jan.2020
--- Content provided by FirstRanker.com ---
Mechanical Measurements and MetrologyTime: 3 hrs. Max. Marks: 100
Note: Answer ant' FIVE fall questions, choosing ONE full question from each module.
Module-1
1 a. Define Metrology. What are the objectives of metrology? (06 Marks)
--- Content provided by FirstRanker.com ---
b. Differentiate line and end standards with examples. (06 Marks)c. Four length bars A, B, C, D of approximately 250mm each are to be calibrated with standard
calibrated metre bar which is actually 0.0008mm less than a metre. It is also found that, bar
`B' is 0.0002mm longer than bar 'A', bar 'C' is 0.0004mm longer than bar 'A' and bar '13"
is 0.0001mm shorter than bar 'A'. The length of all four bars put together is 0.0003mm
--- Content provided by FirstRanker.com ---
longer than the calibrated standard metre. Determine the actual dimensions of each bar.(08 Marks)
OR
2 a. Explain with neat sketches wringing phenomena of slip gauges. (06 Marks)
b. Build the following lengths by using M-112 set of slip gauges and write their combinations:
--- Content provided by FirstRanker.com ---
i) 29.875mm ii) 101.345mm iii) 78.3665mm (09 Marks)c. Explain with neat sketches how a sine bar can be used to measure an unknown angle.
(05 Marks)
3 a. Define tolerance with types.
b. Define fit. Explain different types of fits with sketches.
--- Content provided by FirstRanker.com ---
c. Discuss hole and shaft basic system with neat sketches.OR
4 a. List essential considerations and materials used for construction of gauges. (04 Marks)
b.
Determine the tolerances on the hole and the shaft for a precision running fit designated by
--- Content provided by FirstRanker.com ---
501-17g6. Given:i) 50mm lies between 30-50 mm
ii) i(Microns) = 0.45 (D)" + 0.001D
iii) Fundamental deviation for, H = 0
iv) Fundamental deviation for "g" shaft = -2.5D
--- Content provided by FirstRanker.com ---
?34.
v) ITS = 16i and IT6 = 10i (08 Marks)
c. Explain with neat sketches double ended plug and snap gauges. (08 Marks)
Module-3
--- Content provided by FirstRanker.com ---
5 a. Explain terminology of screw thread. (06 Marks)b. Derive an equation for measuring effective diameter of screw thread by using 2-wire
method. (08 Marks)
c. With neat sketch, explain tool Maker's microscope. (06 Marks)
(06 Marks)
--- Content provided by FirstRanker.com ---
(08 Marks)(06 Marks)
1 of 2
171N1E46B/17MEB406
OR
--- Content provided by FirstRanker.com ---
6 a. Illustrate the principle of interferometry with sketches. (10 Marks)b. Explain construction and working of co-ordinate measuring machine. (10 Marks)
Module-4
7 a. Explain the concept of generalized measurement system with block diagram with bourdon
pressure gauge as an example. (08 Marks)
--- Content provided by FirstRanker.com ---
b. Define the following terms: i) Precision ii) Hysterisis iii) Sensitivity (06 Marks)c. Explain linear variable differential transducer (LVDT) with neat sketch. (06 Marks)
OR
8 a. Explain with a block diagram telemetering receiving system.
b. Explain with a neat sketch cathode ray oscilloscope.
--- Content provided by FirstRanker.com ---
c. What are X-Y plotters? With block diagram explain working of X-Y plotters.Module-5
9 a. Explain working of proving ring with neat sketch.
b. With a neat sketch, explain the working of prong brake dynamometer.
c. Discuss the working of McLeod gauge.
--- Content provided by FirstRanker.com ---
(04 Marks)(08 Marks)
(08 Marks)
(06 Marks) -
(08 Marks)
--- Content provided by FirstRanker.com ---
(08 Marks)OR
10 a. State and explain the laws of thermocouple. (06 Marks)
b. Discuss the construction and working of an optical pyrometer. (10 Marks)
c. Describe the steps to be taken for the preparation of specimen and mounting and strain
--- Content provided by FirstRanker.com ---
gauges. (04 Marks). 2 of 2
FirstRanker.com - FirstRanker's Choice