Download PTU. I.K. Gujral Punjab Technical University (IKGPTU) M.Tech Mech Eng 1st Semester 38204 ADVANCE HEAT AND MASS TRANSFER Question Paper.

Roll No. Total No. of Pages : 02

Total No. of Questions : 08

M.Tech.(ME) (Sem.?1)

ADVANCE HEAT AND MASS TRANSFER

Subject Code : MME-503

M.Code : 38204

Time : 3 Hrs. Max. Marks : 100

INSTRUCTIONS TO CANDIDATES :

1. Attempt any FIVE questions out of EIGHT questions.

2. Each question carries TWENTY marks.

1. Derive the one dimensional steady state conduction equation with internal distributed

heat source.

2. a) Alloy tool steels can be hardened by cooling them in air or oil. A rectangular block

10cm long, 2cm wide and 2cm thick is hardened by heating it to 890?C and cooling

it. Estimate the time required to cool it from 890?C to 400?C and the rate of cooling

when its temperature is 500?C if it is cooled (i) in a current of air at 30?C with a

surface heat transfer coefficient of 110W/m

2

?C, (ii) by immersing it in a large bath of

oil at 30?C with convective heat transfer coefficient of 200W/m

2

?C. The properties of

alloy steel are; c

p

= 580j/kg K,k = 28 W/m K and ? = 7850kg/m

3

.

b) What is internal energy generation? Give some examples where internal energy

generation occurs.

3. Steam is generated on the surfaces of tubes (surrounded by water) with pressurized water

flowing inside 25mm I.D. tubes. At a distance of 2.5m from the inlet of the tube, the

velocity of the water is3 m/s and the temperature of the water is 280?C. The tube surface

is at 250?C. To get an appreciation of the values of the heat transfer coefficients from the

different correlations, find the convective heat transfer coefficient by different

correlations.

4. a) Give the difference between heat transfer in laminar flow and turbulent flow.

b) Discuss Reynold's analogy between skin friction aad heat transfer.

5. Briefly explain the following :

a) Planck?s Law

b) Lambert?s cosine law

c) Explain Absorptivity, Reflectivity and Transmissivity and give relations between

them.

FirstRanker.com - FirstRanker's Choice

1 | M - 3 8 2 0 4 ( S 9 ) - 9 7 9

Roll No. Total No. of Pages : 02

Total No. of Questions : 08

M.Tech.(ME) (Sem.?1)

ADVANCE HEAT AND MASS TRANSFER

Subject Code : MME-503

M.Code : 38204

Time : 3 Hrs. Max. Marks : 100

INSTRUCTIONS TO CANDIDATES :

1. Attempt any FIVE questions out of EIGHT questions.

2. Each question carries TWENTY marks.

1. Derive the one dimensional steady state conduction equation with internal distributed

heat source.

2. a) Alloy tool steels can be hardened by cooling them in air or oil. A rectangular block

10cm long, 2cm wide and 2cm thick is hardened by heating it to 890?C and cooling

it. Estimate the time required to cool it from 890?C to 400?C and the rate of cooling

when its temperature is 500?C if it is cooled (i) in a current of air at 30?C with a

surface heat transfer coefficient of 110W/m

2

?C, (ii) by immersing it in a large bath of

oil at 30?C with convective heat transfer coefficient of 200W/m

2

?C. The properties of

alloy steel are; c

p

= 580j/kg K,k = 28 W/m K and ? = 7850kg/m

3

.

b) What is internal energy generation? Give some examples where internal energy

generation occurs.

3. Steam is generated on the surfaces of tubes (surrounded by water) with pressurized water

flowing inside 25mm I.D. tubes. At a distance of 2.5m from the inlet of the tube, the

velocity of the water is3 m/s and the temperature of the water is 280?C. The tube surface

is at 250?C. To get an appreciation of the values of the heat transfer coefficients from the

different correlations, find the convective heat transfer coefficient by different

correlations.

4. a) Give the difference between heat transfer in laminar flow and turbulent flow.

b) Discuss Reynold's analogy between skin friction aad heat transfer.

5. Briefly explain the following :

a) Planck?s Law

b) Lambert?s cosine law

c) Explain Absorptivity, Reflectivity and Transmissivity and give relations between

them.

2 | M - 3 8 2 0 4 ( S 9 ) - 9 7 9

6. A 0.5m

2

plane, gray, diffuse, opaque surface with a = 0.7 is maintained at 500?C. With an

irradiation G, of 10,000W/m

2

, determine the following :

(a) Absorbed energy

(b) Emitted energy

(c) Total energy leawng the surface per unit area

(d) Radiant energy emitted by the surface in the wave band of 0.2 ?m to 4 ?m

Net radiative heat transfer rate from the surface.

7. In a laboratory experiment, air at 347K and 1 atm flows at a high speed around a single

naphthalene (C

10

H

8

) sphere, this sublimates partially. When the experiment begins, the

diameter of the sphere is 2.0cm. At the end of the experiment, 14.32min later, the

diameter of the sphere is 1.85cm. Estimate the mass-transfer coefficient when the driving

force is expressed in terms of molar concentrations. The density of naphthalene is

1.145g/cc and its vapour pressure at 347K is 670Pa. Molecular weight of naphthalene is

128.2.

8. a) Explain Fick?s law of Diffusion.

b) Explain :

(i) Convective Mass transfer

(ii) Mass Transfer Coefficient

NOTE : Disclosure of Identity by writing Mobile No. or Making of passing request on any

page of Answer Sheet will lead to UMC against the Student.

FirstRanker.com - FirstRanker's Choice

This post was last modified on 13 December 2019