Download PTU. I.K. Gujral Punjab Technical University (IKGPTU) M.Tech Mech Eng 1st Semester 74719 ADVANCED THERMODYNAMICS Question Paper.
Roll No. Total No. of Pages : 02
Total No. of Questions : 08
M.Tech. (ME) (2017 Batch) (Sem.?1)
ADVANCED THERMODYNAMICS
Subject Code : MTME-105
M.Code : 74719
Time : 3 Hrs. Max. Marks : 100
INSTRUCTIONS TO CANDIDATES :
1. Attempt any FIVE questions in all, out of EIGHT questions.
2. Each question carry TWENTY marks.
l. Briefly explain the following :
(a) Vander Waal's equation 5
(b) Sensible Heating 5
(c) Relative Humidity 5
(d) Refrigeration effect 5
2. (a) What is cooling tower? Explain various types of cooling tower? 10
(b) Draw and explain the various processes in psychometric chart. 10
3. Determine the molal analysis of the products of combustion when octane C
8
H
18
is burned
with 200% theoretical air and determine the dew point of the products if the pressure is 0.
IMpa. 20
4. (a) Explain the effects of non-reacting gases equilibrium in multiple reactions. 10
(b) Explain the enthalpy of formation in detail with context of combustion process. 10
5. In an air-standard Brayton cycle the air enters the compressor at 0.1 MPa and 15?C. The
pressure leaving the compressor is 1.0 MPa, and the maximum temperature in the cycle is
1100?C. Determine the pressure and temperature at each point in the cycle and the
compressor work, turbine work, and cycle efficiency. For each of the control volumes
analyzed, the model is ideal gas with constant specific heat, at 300 K, and each process is
steady state with no kinetic or potential energy changes. 20
FirstRanker.com - FirstRanker's Choice
1 | M-74719 (S9)-2784
Roll No. Total No. of Pages : 02
Total No. of Questions : 08
M.Tech. (ME) (2017 Batch) (Sem.?1)
ADVANCED THERMODYNAMICS
Subject Code : MTME-105
M.Code : 74719
Time : 3 Hrs. Max. Marks : 100
INSTRUCTIONS TO CANDIDATES :
1. Attempt any FIVE questions in all, out of EIGHT questions.
2. Each question carry TWENTY marks.
l. Briefly explain the following :
(a) Vander Waal's equation 5
(b) Sensible Heating 5
(c) Relative Humidity 5
(d) Refrigeration effect 5
2. (a) What is cooling tower? Explain various types of cooling tower? 10
(b) Draw and explain the various processes in psychometric chart. 10
3. Determine the molal analysis of the products of combustion when octane C
8
H
18
is burned
with 200% theoretical air and determine the dew point of the products if the pressure is 0.
IMpa. 20
4. (a) Explain the effects of non-reacting gases equilibrium in multiple reactions. 10
(b) Explain the enthalpy of formation in detail with context of combustion process. 10
5. In an air-standard Brayton cycle the air enters the compressor at 0.1 MPa and 15?C. The
pressure leaving the compressor is 1.0 MPa, and the maximum temperature in the cycle is
1100?C. Determine the pressure and temperature at each point in the cycle and the
compressor work, turbine work, and cycle efficiency. For each of the control volumes
analyzed, the model is ideal gas with constant specific heat, at 300 K, and each process is
steady state with no kinetic or potential energy changes. 20
2 | M-74719 (S9)-2784
6. Consider a regenerative cycle using steam as the working fluid. Steam leaves the boiler
and enters the turbine at 4 MPa, 400?C. After expansion to 400 kPa, some of the steam is
extracted from the turbine for the purpose of heating the feed water in an open feed water
heater. The pressure in the feed water heater is 400 kPa and water leaving it is saturated
liquid at 400 kPa. The steam not extracted expands to 10kPa. Determine the cycle
efficiency. 20
7. Write a short note on following :
(a) Photovoltaic cells 10
(b) Magneto Hydrodynamic Generators 10
8. (a) Explain the phenomenological laws in detail. 10
(b) Discuss Heat flux and entropy production in context of irreversible process. 10
NOTE : Disclosure of Identity by writing Mobile No. or Making of passing request on any
page of Answer Sheet will lead to UMC against the Student.
FirstRanker.com - FirstRanker's Choice
This post was last modified on 13 December 2019