Subject Code: 2160911 Date: 12/12/2019
Subject Name: Computer Aided Analysis and Design for Electrical Engg.
--- Content provided by FirstRanker.com ---
Time: 02:30 PM TO 05:00 PM Total Marks: 70
Instructions:
- Attempt all questions.
- Make suitable assumptions wherever necessary.
- Figures to the right indicate full marks.
--- Content provided by FirstRanker.com ---
GUJARAT TECHNOLOGICAL UNIVERSITY
BE - SEMESTER- VI (New) EXAMINATION - WINTER 2019
Q.1 (a) State the performance parameters expected to be outputted on running any Computer Aided Design program. 04
(b) Compare top down and bottom up approaches in CAD programs. State example of the same. 07
(c) Explain general procedure to design DC machine optimally drawing flowchart of the same. 07
--- Content provided by FirstRanker.com ---
Q.2 (a) State requirements of the high conductive materials 03
(b) Explain properties of low, medium and high hysteresis losses material drawing hysteresis loops of any three materials. 04
(c) Consider the case of a single-phase induction motor seems to draw full load current at 60% of rated load. Estimate probable causes for the same. 07
OR
(c) Discuss how Finite Analysis helps to improve design to overcome above problem. Describe steps involved in process in brief. 07
--- Content provided by FirstRanker.com ---
Q.3 (a) Interpret role of FE Analysis tool in conventional Computer Aided Designing process. 03
(b) Explain significance and function of followings in respect to FE Analysis: 04
- Meshing
- Boundary conditions
- Static analysis
- Transient analysis
--- Content provided by FirstRanker.com ---
(c) Suggest type of slot winding out of following options: (A) Integral slot winding (B) Fractional slot winding For 3 phase, 4 pole, 66 slots armature. (show calculations and justify your answer in one-two lines) 07
OR
(a) State the significance of specific magnetic loading. 03
(b) Identify sequential steps for designing a small transformer. 04
--- Content provided by FirstRanker.com ---
(c) Evaluate significance of optimal selection Max-Min range of following parameters for distribution transformer. 07
- kg/kV A
- Efficiency
- inrush current
- Maximum flux density in core.
--- Content provided by FirstRanker.com ---
Q.4 (a) State criteria for selection of type of armature windings out of Lap or Wave. 03
(b) Estimate requirement of dummy coil for following armature winding. 4 pole, 18 slot, double layer is to be designed with wave winding. 04
(c) Develop algorithm for design of starting resistance for DC motor. 07
OR
Q.4 (a) State the classes of insulation in transformers based on temperature. 03
--- Content provided by FirstRanker.com ---
(b) Explain sequential steps for drawing Lap winding diagram. 04
(c) Predict the change in performance of DC machine with change in following design parameters: 07
- Pole arc to pole pitch ratio
- Core flux density
- Slots per pole per phase
--- Content provided by FirstRanker.com ---
Q.5 (a) Develop algorithmic steps for the design of Tank for oil natural air forced type transformer casing. 03
(b) Differentiate design criteria for shunt, series and separately excited DC motors. 04
(c) Explain significance of different types of enclosures for rotating DC machines. 07
Q.5 (a) State standard rating of distribution transformer for LT consumer. 03
(b) Develop heat flow diagram in rotating DC machines. 04
--- Content provided by FirstRanker.com ---
(c) Illustrate a case of design-optimization where FE Analysis of electrostatic field in transformer with appropriate diagrams. 07
Q.3 (a) Discuss the algorithmic steps 3-point starter design 03
(b) Illustrate a case of design optimization where FE Analysis of electrostatic field with appropriate diagrams. 04
--- Content provided by FirstRanker.com ---
This download link is referred from the post: GTU BE/B.Tech 2019 Winter Question Papers || Gujarat Technological University