--- Content provided by FirstRanker.com ---/1
Code No. : 3318/N
FACULTY OF ENGINEERIN & INFORMATICS
E.E. I Year (New) (Common to all Branches) (Main) Examination, June 2011
ENGINEERING GRAPHICS
Note : Answer all questions from Part A, answer any five questions from Part B. .
PART A (35 Marks)
1. Match the following :
4
equal squares.
. Tetrahedron (b) Front view above XY
and top view below XY
(c) Rectangle method
a number
(e) Has four equal faces,
each an equilateral
trian?Ie.
3. Use inscrible circle method to construct a pentagon of 30 mm side. 3
4. What are solids of revolution ? Give three examples and their formation. 4
5. A room of 1728 M
3
2
volume. Find
R.F and construct a scale to measure upto 42 m. 4
6. Differentiate between a section and a section at view. 2
solids. 4
8. Draw the development of a tetrahedron of side 30 mm. 5
9. Differentiate between an 'Isometric projection' and 'Isometric view' of
an object. 4
PART ? B (65 Marks)
11. (a) Construct a hypocycloid for a rolling circle 50 mm diameter and
directing circle 180 mm diameter. 6
(b) Construct a scale with R.F = 1/2.5 to show decimetres, centimetres
on it a distance of 1.48 dm, 0.48 dm and 2.64 dm. 7
. Diagonal scale
. First angle Projection
(This paper contains 2 pages) 1 P.T.O.
Sv
?
)
*11. Su4e 2.
/1
Code No. : 3318/N
FACULTY OF ENGINEERIN & INFORMATICS
E.E. I Year (New) (Common to all Branches) (Main) Examination, June 2011
Time : 3 Hours ] [ Max. Marks : 100
Note : Answer all questions from Part A, answer any five questions from Part B. .
PART A (35 Marks)
1. Match the following :
1. Hyperbola can be drawn by (a) Has six equal faces, all
equal squares.
. Tetrahedron (b) Front view above XY
and top view below XY
(d) To represent 3 units of
a number
(e) Has four equal faces,
each an equilateral
2. What data is required to construct a scale 2
3. Use inscrible circle method to construct a pentagon of 30 mm side. 3
4. What are solids of revolution ? Give three examples and their formation. 4
5. A room of 1728 M
volume is shown by a cube of 216 cm
2
volume. Find
R.F and construct a scale to measure upto 42 m. 4
7. Explain the cutting plane method of drawing curves of interpenetration of
solids. 4
8. Draw the development of a tetrahedron of side 30 mm. 5
9. Differentiate between an 'Isometric projection' and 'Isometric view' of
10. Draw an involute of a line of 10 mm for 5 turns. 3
PART ? B (65 Marks)
11. (a) Construct a hypocycloid for a rolling circle 50 mm diameter and
directing circle 180 mm diameter. 6
and millimetres by a vernier and to measure upto 4 decimetres. Mark
on it a distance of 1.48 dm, 0.48 dm and 2.64 dm. 7
. Diagonal scale
. First angle Projection
Code Noe o 3318/N
12.
A line PQ is in the first quadrant. Its ends P and Q are 20 mm and 60 mm
in front of the V.P respectively. The distance between the end projectors is
?
to the V.P, with its end in H.P. Draw
the projections of PQ and find its true length and the inclination with the
H.P. Also locate its H.T.
13. Draw the projections of a pentagonal plane, side 25 mm resting on the H.P
on one of its edges. The plane of the pentagon is inclined at 45
?
to the H.P
an angle of 30
?
with the V.P. 13
14. A square prism of base 40 mm is resting on HP with its base sides equally
?
to H.P. It is cut by a
horizontal plane bisecting axis. Draw the true shape of the section, if the
axis is 80 mm. 13
long, the smaller diagonal of which is parallel to both the principal planes,
while the other is inclined at 30
?
to H.P. 13
cylinder of 40 mm dia, such that the axis of the cylinder is parallel to the
axis of the cone, at a distance of 5 mm. Draw the projections, showing the
curves of intersection when (a) the plane containing the axes of the solids
is parallel to V.P and (b) when the plane containing the axes of the solids
?
to V.P. 13
17. A right circular cone of dia. 30 mm base and height 36 mm rests centrally
on top of a square block of 48 mm side and 22 mm thick. Draw the
2 5,900
FirstRanker.com - FirstRanker's Choice
Code No. : 3318/N
FACULTY OF ENGINEERIN & INFORMATICS
E.E. I Year (New) (Common to all Branches) (Main) Examination, June 2011
ENGINEERING GRAPHICS
--- Content provided by FirstRanker.com ---
Time : 3 Hours ] [ Max. Marks : 100Note : Answer all questions from Part A, answer any five questions from Part B. .
PART A (35 Marks)
1. Match the following :
4
--- Content provided by FirstRanker.com ---
1. Hyperbola can be drawn by (a) Has six equal faces, allequal squares.
. Tetrahedron (b) Front view above XY
and top view below XY
(c) Rectangle method
--- Content provided by FirstRanker.com ---
(d) To represent 3 units ofa number
(e) Has four equal faces,
each an equilateral
trian?Ie.
--- Content provided by FirstRanker.com ---
2. What data is required to construct a scale 23. Use inscrible circle method to construct a pentagon of 30 mm side. 3
4. What are solids of revolution ? Give three examples and their formation. 4
5. A room of 1728 M
3
--- Content provided by FirstRanker.com ---
volume is shown by a cube of 216 cm2
volume. Find
R.F and construct a scale to measure upto 42 m. 4
6. Differentiate between a section and a section at view. 2
--- Content provided by FirstRanker.com ---
7. Explain the cutting plane method of drawing curves of interpenetration ofsolids. 4
8. Draw the development of a tetrahedron of side 30 mm. 5
9. Differentiate between an 'Isometric projection' and 'Isometric view' of
an object. 4
--- Content provided by FirstRanker.com ---
10. Draw an involute of a line of 10 mm for 5 turns. 3PART ? B (65 Marks)
11. (a) Construct a hypocycloid for a rolling circle 50 mm diameter and
directing circle 180 mm diameter. 6
(b) Construct a scale with R.F = 1/2.5 to show decimetres, centimetres
--- Content provided by FirstRanker.com ---
and millimetres by a vernier and to measure upto 4 decimetres. Markon it a distance of 1.48 dm, 0.48 dm and 2.64 dm. 7
. Diagonal scale
. First angle Projection
(This paper contains 2 pages) 1 P.T.O.
--- Content provided by FirstRanker.com ---
FirstRanker.com - FirstRanker's ChoiceSv
?
)
*11. Su4e 2.
--- Content provided by FirstRanker.com ---
0/1
Code No. : 3318/N
FACULTY OF ENGINEERIN & INFORMATICS
E.E. I Year (New) (Common to all Branches) (Main) Examination, June 2011
--- Content provided by FirstRanker.com ---
ENGINEERING GRAPHICSTime : 3 Hours ] [ Max. Marks : 100
Note : Answer all questions from Part A, answer any five questions from Part B. .
PART A (35 Marks)
1. Match the following :
--- Content provided by FirstRanker.com ---
41. Hyperbola can be drawn by (a) Has six equal faces, all
equal squares.
. Tetrahedron (b) Front view above XY
and top view below XY
--- Content provided by FirstRanker.com ---
(c) Rectangle method(d) To represent 3 units of
a number
(e) Has four equal faces,
each an equilateral
--- Content provided by FirstRanker.com ---
trian?Ie.2. What data is required to construct a scale 2
3. Use inscrible circle method to construct a pentagon of 30 mm side. 3
4. What are solids of revolution ? Give three examples and their formation. 4
5. A room of 1728 M
--- Content provided by FirstRanker.com ---
3volume is shown by a cube of 216 cm
2
volume. Find
R.F and construct a scale to measure upto 42 m. 4
--- Content provided by FirstRanker.com ---
6. Differentiate between a section and a section at view. 27. Explain the cutting plane method of drawing curves of interpenetration of
solids. 4
8. Draw the development of a tetrahedron of side 30 mm. 5
9. Differentiate between an 'Isometric projection' and 'Isometric view' of
--- Content provided by FirstRanker.com ---
an object. 410. Draw an involute of a line of 10 mm for 5 turns. 3
PART ? B (65 Marks)
11. (a) Construct a hypocycloid for a rolling circle 50 mm diameter and
directing circle 180 mm diameter. 6
--- Content provided by FirstRanker.com ---
(b) Construct a scale with R.F = 1/2.5 to show decimetres, centimetresand millimetres by a vernier and to measure upto 4 decimetres. Mark
on it a distance of 1.48 dm, 0.48 dm and 2.64 dm. 7
. Diagonal scale
. First angle Projection
--- Content provided by FirstRanker.com ---
(This paper contains 2 pages) 1 P.T.O.Code Noe o 3318/N
12.
A line PQ is in the first quadrant. Its ends P and Q are 20 mm and 60 mm
in front of the V.P respectively. The distance between the end projectors is
--- Content provided by FirstRanker.com ---
75 mm. The line is inclined at 30?
to the V.P, with its end in H.P. Draw
the projections of PQ and find its true length and the inclination with the
H.P. Also locate its H.T.
--- Content provided by FirstRanker.com ---
1313. Draw the projections of a pentagonal plane, side 25 mm resting on the H.P
on one of its edges. The plane of the pentagon is inclined at 45
?
to the H.P
--- Content provided by FirstRanker.com ---
and the perpendicular drawn from the mid point of the resting edge makesan angle of 30
?
with the V.P. 13
14. A square prism of base 40 mm is resting on HP with its base sides equally
--- Content provided by FirstRanker.com ---
inclined to both H.P and V.P and its axis inclined at 45?
to H.P. It is cut by a
horizontal plane bisecting axis. Draw the true shape of the section, if the
axis is 80 mm. 13
--- Content provided by FirstRanker.com ---
15. Draw the projections of rhombus, having diagonals 120 mm and 60 mmlong, the smaller diagonal of which is parallel to both the principal planes,
while the other is inclined at 30
?
to H.P. 13
--- Content provided by FirstRanker.com ---
16. A vertical cone of base 60 mm dia and axis 70 mm long is penetrated by acylinder of 40 mm dia, such that the axis of the cylinder is parallel to the
axis of the cone, at a distance of 5 mm. Draw the projections, showing the
curves of intersection when (a) the plane containing the axes of the solids
is parallel to V.P and (b) when the plane containing the axes of the solids
--- Content provided by FirstRanker.com ---
is inclined at 60?
to V.P. 13
17. A right circular cone of dia. 30 mm base and height 36 mm rests centrally
on top of a square block of 48 mm side and 22 mm thick. Draw the
--- Content provided by FirstRanker.com ---
isometric projection of the two solids. 132 5,900
FirstRanker.com - FirstRanker's Choice