Download AKTU (Dr. A.P.J. Abdul Kalam Technical University (AKTU), formerly Uttar Pradesh Technical University (UPTU)) B-Tech 4th Semester (Fourth Semester) 2018-19 REC401 Microprocessors Microcontrollers Question Paper
| 14-May-2019 09:00:46 | 45.115.62.2
FirstRanker.com | 14-May-2019 09:00:46 | 45.115.62.2
REC401
Page 1 of 2
Printed Pages: 02 Sub Code: REC401
Paper Id: 131288 Roll No.
B TECH
(SEM-IV) THEORY EXAMINATION 2018-19
MICROPROCESSORS & MICROCONTROLLERS
Time: 3 Hours Total Marks: 70
Note: 1. Attempt all Sections. If require any missing data; then choose suitably.
SECTION A
1. Attempt all questions in brief. 2 x 7 = 14
a) Describe how status and Control signal are generated from 8085 pins.
b) Explain the concept of Direct Memory Access.
c) Explain the difference between microprocessor and microcontroller.
d) What are embedded systems? Describe some the applications of embedded systems.
e) Explain the low power modes of MSP430.
f) What is UART?
g) What are software interrupts?
SECTION B
2. Attempt any three of the following: 7 x 3 = 21
a) Explain how Address and Data Bus are multiplexed in 8085 microprocessor and how
demultiplexing is done. Describe the advantage of using multiplexed Address and
Data Buses. Describe the role of ALE signal in DE multiplexing the buses.
b) Describe the various Interrupts of 8085 microprocessor. Classify the interrupts of
8085 as maskable or non-maskable and vectored or non-vectored.
c) Describe the Programming System registers of MSP430. Explain the concept and the
function of Pull-up and Pull-down registers using suitable diagrams.
d) Explain the concept of Interrupts. Compare the polling method with interrupt driven
method. Name the interrupts of MSP430 and describe the sources of interrupts.
e) For an MSP430 based embedded system application and using the interface protocols
for communication with external devices, design and explain the functioning of A
Low-Power Battery less Wireless Temperature and Humidity Sensor with Passive
Low Frequency RFID.
SECTION C
3. Attempt any one part of the following: 7 x 1 = 7
(a) Define the term instruction set. Explain the Classification of instructions on the basis
of their functions. Give some examples of each type.
(b) Describe the significance of the term addressing modes. Explain the various
addressing modes of 8085 with suitable examples.
4. Attempt any one part of the following: 7 x 1 = 7
(a) Draw the block diagram of 8259A programmable Interrupt Controller and explain the
function of each block. Explain how priority of different interrupts is decided in
programmable Interrupt Controller.
(b) Draw the block diagram of 8255A programmable Parallel interface. Write the
different modes of 8255 and explain how the ports of IC8255 can be used in different
modes. Explain the control word of BSR and I/O modes.
FirstRanker.com - FirstRanker's Choice
FirstRanker.com
| 14-May-2019 09:00:46 | 45.115.62.2
FirstRanker.com | 14-May-2019 09:00:46 | 45.115.62.2
REC401
Page 1 of 2
Printed Pages: 02 Sub Code: REC401
Paper Id: 131288 Roll No.
B TECH
(SEM-IV) THEORY EXAMINATION 2018-19
MICROPROCESSORS & MICROCONTROLLERS
Time: 3 Hours Total Marks: 70
Note: 1. Attempt all Sections. If require any missing data; then choose suitably.
SECTION A
1. Attempt all questions in brief. 2 x 7 = 14
a) Describe how status and Control signal are generated from 8085 pins.
b) Explain the concept of Direct Memory Access.
c) Explain the difference between microprocessor and microcontroller.
d) What are embedded systems? Describe some the applications of embedded systems.
e) Explain the low power modes of MSP430.
f) What is UART?
g) What are software interrupts?
SECTION B
2. Attempt any three of the following: 7 x 3 = 21
a) Explain how Address and Data Bus are multiplexed in 8085 microprocessor and how
demultiplexing is done. Describe the advantage of using multiplexed Address and
Data Buses. Describe the role of ALE signal in DE multiplexing the buses.
b) Describe the various Interrupts of 8085 microprocessor. Classify the interrupts of
8085 as maskable or non-maskable and vectored or non-vectored.
c) Describe the Programming System registers of MSP430. Explain the concept and the
function of Pull-up and Pull-down registers using suitable diagrams.
d) Explain the concept of Interrupts. Compare the polling method with interrupt driven
method. Name the interrupts of MSP430 and describe the sources of interrupts.
e) For an MSP430 based embedded system application and using the interface protocols
for communication with external devices, design and explain the functioning of A
Low-Power Battery less Wireless Temperature and Humidity Sensor with Passive
Low Frequency RFID.
SECTION C
3. Attempt any one part of the following: 7 x 1 = 7
(a) Define the term instruction set. Explain the Classification of instructions on the basis
of their functions. Give some examples of each type.
(b) Describe the significance of the term addressing modes. Explain the various
addressing modes of 8085 with suitable examples.
4. Attempt any one part of the following: 7 x 1 = 7
(a) Draw the block diagram of 8259A programmable Interrupt Controller and explain the
function of each block. Explain how priority of different interrupts is decided in
programmable Interrupt Controller.
(b) Draw the block diagram of 8255A programmable Parallel interface. Write the
different modes of 8255 and explain how the ports of IC8255 can be used in different
modes. Explain the control word of BSR and I/O modes.
FirstRanker.com
| 14-May-2019 09:00:46 | 45.115.62.2
FirstRanker.com | 14-May-2019 09:00:46 | 45.115.62.2
REC401
Page 2 of 2
5. Attempt any one part of the following: 7 x 1 = 7
(a) Differentiate between the following:
i. Von Neumann (Princeton) and Harvard architecture
ii. RISC and CISC machines
(b) In relation to the low power aspects of MSP430, Explain the Active current
consumption and Standby current consumption.
6. Attempt any one part of the following: 7 x 1 = 7
(a) Describe the system clock structure of MSP430. Explain the concepts and function of
Watchdog timer and Real Time Clock (RTC) of MSP430.
(b) Describe the Analog to digital Conversion Mechanism in MSP430. Explain Direct
Memory Access (DMA) in MSP430.
7. Attempt any one part of the following: 7 x 1 = 7
(a) Describe the various serial communication interfaces used in MSP430. Give a
comparison of the different serial communication interfaces.
(b) What is I2C protocol? What is the maximum number of slaves that can be connected
to a single master of I2C bus?
FirstRanker.com - FirstRanker's Choice
This post was last modified on 29 January 2020