# Download JNTUA B.Tech 1-1 R13 2017 Dec Supply 13A01101 Engineering Mechanics Question Paper

Download JNTUA (JNTU Anantapur) B.Tech R13 (Bachelor of Technology) 1st Year 1st Semester (1-1) 2017 Dec Supply 13A01101 Engineering Mechanics Previous Question Paper || Download B-Tech 1st Year 1st Sem 13A01101 Engineering Mechanics Question Paper || JNTU Anantapur B.Tech 1-1 Previous Question Paper || JNTU Anantapur B.Tech ME 1-1 Previous Question Paper || JNTU Anantapur B.Tech CSE 1-1 Previous Question Paper || JNTU Anantapur B.Tech Mech 1-1 Previous Question Paper || JNTU Anantapur B.Tech EEE 1-1 Previous Question Paper || JNTU Anantapur B.Tech ECE 1-1 Previous Question Paper

www.FirstRanker.com

Code: 13A01101

B.Tech I Year (R13) Supplementary Examinations December 2017
ENGINEERING MECHANICS
(Common to CE and ME)
Time: 3 hours Max. Marks: 70

PART ? A
(Compulsory Question)

*****
1 Answer the following: (10 X 02 = 20 Marks)
(a) State the principle of transmissibility of forces.
(b) A force of 15 N is applied perpendicular to the edge of a door 0.8 m wide as shown in figure below. Find
the moment of the force about the hinge.

(c) List the two types of dynamic friction.
(d) Coefficient of friction between screw and nut in a screw jack is 0.15. Determine the angle of friction.
(e) Locate the centroid of the lamina shown in figure below.

(f) State perpendicular axis theorem with simple sketch.
(g) A body is moving with a velocity of 3 m/s. After five seconds the velocity of the body becomes 13 m/s.
Find the acceleration of the body.
(h) A lift carries a weight of 100 N and is moving with a uniform acceleration of 2.45 m/s
2
. Determine the
tension in the cables supporting the lift when the lift is moving upwards.
(i) List any two assumptions made in the analysis of frames.
(j) A simple harmonic motion is defined by the expression a = -15s. Determine its period and frequency.

PART ? B
(Answer all five units, 5 X 10 = 50 Marks)

UNIT ? I

2 A 40 kg cylinder is held in position on an inclined plane by means of a wire as shown in figure below.
Determine reaction at surface of inclined plane and tension in the wire.

OR
Contd. in page 2

Page 1 of 3
R13
15 N
0.8 m
A
O
www.FirstRanker.com www.FirstRanker.com
www.FirstRanker.com
FirstRanker.com - FirstRanker's Choice
www.FirstRanker.com

Code: 13A01101

B.Tech I Year (R13) Supplementary Examinations December 2017
ENGINEERING MECHANICS
(Common to CE and ME)
Time: 3 hours Max. Marks: 70

PART ? A
(Compulsory Question)

*****
1 Answer the following: (10 X 02 = 20 Marks)
(a) State the principle of transmissibility of forces.
(b) A force of 15 N is applied perpendicular to the edge of a door 0.8 m wide as shown in figure below. Find
the moment of the force about the hinge.

(c) List the two types of dynamic friction.
(d) Coefficient of friction between screw and nut in a screw jack is 0.15. Determine the angle of friction.
(e) Locate the centroid of the lamina shown in figure below.

(f) State perpendicular axis theorem with simple sketch.
(g) A body is moving with a velocity of 3 m/s. After five seconds the velocity of the body becomes 13 m/s.
Find the acceleration of the body.
(h) A lift carries a weight of 100 N and is moving with a uniform acceleration of 2.45 m/s
2
. Determine the
tension in the cables supporting the lift when the lift is moving upwards.
(i) List any two assumptions made in the analysis of frames.
(j) A simple harmonic motion is defined by the expression a = -15s. Determine its period and frequency.

PART ? B
(Answer all five units, 5 X 10 = 50 Marks)

UNIT ? I

2 A 40 kg cylinder is held in position on an inclined plane by means of a wire as shown in figure below.
Determine reaction at surface of inclined plane and tension in the wire.

OR
Contd. in page 2

Page 1 of 3
R13
15 N
0.8 m
A
O
www.FirstRanker.com www.FirstRanker.com
www.FirstRanker.com
www.FirstRanker.com

Code: 13A01101

3 Replace the system of forces and couple as shown in figure below, by a single force couple system
at A.

UNIT ? II

4 Two blocks A and B of weights 1 kN and 2 kN, respectively are in equilibrium position as shown in
figure below. lf coefficient of friction between the two blocks as well as the block B and the floor is 0.3,
find the force P required to move the block B. Also find the force in the string.

OR
5 A block placed over a 100 wedge on a horizontal floor and leaning against a vertical wall as shown in
figure below and weighing 1500 N is to be raised by applying a horizontal force to the wedge. Assuming
co-efficient of friction between all the surfaces in contact to be 0.3, determine the minimum horizontal
force to be applied to raise the block.

UNIT ? III

6 Calculate the moment of inertia about horizontal and vertical axes (I
xx
and I
yy
) of the section show in
figure below.

OR
Contd. in page 3

Page 2 of 3
R13
www.FirstRanker.com www.FirstRanker.com
www.FirstRanker.com
FirstRanker.com - FirstRanker's Choice
www.FirstRanker.com

Code: 13A01101

B.Tech I Year (R13) Supplementary Examinations December 2017
ENGINEERING MECHANICS
(Common to CE and ME)
Time: 3 hours Max. Marks: 70

PART ? A
(Compulsory Question)

*****
1 Answer the following: (10 X 02 = 20 Marks)
(a) State the principle of transmissibility of forces.
(b) A force of 15 N is applied perpendicular to the edge of a door 0.8 m wide as shown in figure below. Find
the moment of the force about the hinge.

(c) List the two types of dynamic friction.
(d) Coefficient of friction between screw and nut in a screw jack is 0.15. Determine the angle of friction.
(e) Locate the centroid of the lamina shown in figure below.

(f) State perpendicular axis theorem with simple sketch.
(g) A body is moving with a velocity of 3 m/s. After five seconds the velocity of the body becomes 13 m/s.
Find the acceleration of the body.
(h) A lift carries a weight of 100 N and is moving with a uniform acceleration of 2.45 m/s
2
. Determine the
tension in the cables supporting the lift when the lift is moving upwards.
(i) List any two assumptions made in the analysis of frames.
(j) A simple harmonic motion is defined by the expression a = -15s. Determine its period and frequency.

PART ? B
(Answer all five units, 5 X 10 = 50 Marks)

UNIT ? I

2 A 40 kg cylinder is held in position on an inclined plane by means of a wire as shown in figure below.
Determine reaction at surface of inclined plane and tension in the wire.

OR
Contd. in page 2

Page 1 of 3
R13
15 N
0.8 m
A
O
www.FirstRanker.com www.FirstRanker.com
www.FirstRanker.com
www.FirstRanker.com

Code: 13A01101

3 Replace the system of forces and couple as shown in figure below, by a single force couple system
at A.

UNIT ? II

4 Two blocks A and B of weights 1 kN and 2 kN, respectively are in equilibrium position as shown in
figure below. lf coefficient of friction between the two blocks as well as the block B and the floor is 0.3,
find the force P required to move the block B. Also find the force in the string.

OR
5 A block placed over a 100 wedge on a horizontal floor and leaning against a vertical wall as shown in
figure below and weighing 1500 N is to be raised by applying a horizontal force to the wedge. Assuming
co-efficient of friction between all the surfaces in contact to be 0.3, determine the minimum horizontal
force to be applied to raise the block.

UNIT ? III

6 Calculate the moment of inertia about horizontal and vertical axes (I
xx
and I
yy
) of the section show in
figure below.

OR
Contd. in page 3

Page 2 of 3
R13
www.FirstRanker.com www.FirstRanker.com
www.FirstRanker.com
www.FirstRanker.com

Code: 13A01101

7 Find the moment of inertia of the shaded area shown in the figure below about the axis AB.

UNIT ? IV

8 A car starts from rest and accelerates uniformly to a speed of 80 km/hour over a distance of
500 meters, calculate the acceleration and time taken. If a further acceleration raises the speed to
96 km/hour in 10 seconds, find the acceleration and further distance moved. The brakes are now
applied and the car comes to rest under uniform retardation in 5 seconds. Find the distance travelled
during braking.
OR
9 Two blocks shown in figure below, have weight A = 8N and B = 10N and coefficient of friction between
the block A and horizontal plane, = 0.2. If the system is released, from rest and the block A falls
through a vertical distance of 1.5 m, what is the velocity acquired by it? Neglect the friction in the pulley
and extension of the string.

UNIT ? V

10 Determine the forces in all the members of the frames shown in figure below. Indicate the nature of the
forces also.

OR
11 A particle is in simple harmonic motion. Its maximum velocity was 6 m/sec and the maximum
acceleration was found to be 12 m/sec
2
. Determine its angular velocity, amplitude. Also determine its
velocity and acceleration when displacement is half the amplitude.
*****
Page 3 of 3
R13
www.FirstRanker.com www.FirstRanker.com
www.FirstRanker.com
FirstRanker.com - FirstRanker's Choice

This post was last modified on 11 September 2020