Download GTU (Gujarat Technological University) BE/BTech (Bachelor of Engineering / Bachelor of Technology) 2018 Winter 4th Sem New 2141403 Materials And Manufacture Of Food Equipment Previous Question Paper
1
Seat No.: ________ Enrolment No.___________
GUJARAT TECHNOLOGICAL UNIVERSITY
BE - SEMESTER ?IV (NEW) EXAMINATION ? WINTER 2018
Subject Code: 2141403 Date: 05/12/2018
Subject Name: Materials & Manufacture of Food Equipment
Time: 02:30 PM TO 05:00 PM Total Marks: 70
Instructions:
1. Attempt all questions.
2. Make suitable assumptions wherever necessary.
3. Figures to the right indicate full marks.
Q.1 (a) What is the purpose of heat treatment of metals? 03
(b) Differentiate between first and third angle of projection. 04
(c) Describe the mechanical properties of materials discussing strength,
ductility, toughness, stiffness, malleability, plasticity and elasticity.
07
Q.2 (a) Draw a phase diagram indicating triple point and critical point 03
(b) Define stress and strain. Discuss tensile, compressive and shear
stress with suitable diagram.
04
(c) Draw and describe in detail stress strain curve for material under
load.
07
OR
(c) Draw the stress strain curve for material exhibiting following
properties:
(i) Stiff, ductile and strong
(ii) Stiff, brittle and strong
(iii) Stiff, ductile and weak
(iv) Stiff, brittle and weak
(v) Flexible, brittle and strong
(vi) Flexible, ductile and weak
(vii) Flexible, brittle and weak
07
Q.3 (a) Show diagrammatically eutectic and peritectic reaction in metals. 03
(b) Describe oxy-fuel welding. 04
(c) Answer the following with the help of eutectic phase diagram of Sn-
Pb alloy shown below:
(i) The melting point of Sn and Pb.
(ii) Maximum solubility of Sn in Pb and Pb in Sn.
(iii) For a 40 wt% Sn ?60 wt% Pb alloy at 150
0
C (300
0
F),
1) What phase(s) is (are) present?
2) What is (are) the composition(s) of the phase(s)?
3) The relative amount ofeach phase present?
07
www.FirstRanker.com www.FirstRanker.com
www.FirstRanker.com
FirstRanker.com - FirstRanker's Choice
www.FirstRanker.com
1
Seat No.: ________ Enrolment No.___________
GUJARAT TECHNOLOGICAL UNIVERSITY
BE - SEMESTER ?IV (NEW) EXAMINATION ? WINTER 2018
Subject Code: 2141403 Date: 05/12/2018
Subject Name: Materials & Manufacture of Food Equipment
Time: 02:30 PM TO 05:00 PM Total Marks: 70
Instructions:
1. Attempt all questions.
2. Make suitable assumptions wherever necessary.
3. Figures to the right indicate full marks.
Q.1 (a) What is the purpose of heat treatment of metals? 03
(b) Differentiate between first and third angle of projection. 04
(c) Describe the mechanical properties of materials discussing strength,
ductility, toughness, stiffness, malleability, plasticity and elasticity.
07
Q.2 (a) Draw a phase diagram indicating triple point and critical point 03
(b) Define stress and strain. Discuss tensile, compressive and shear
stress with suitable diagram.
04
(c) Draw and describe in detail stress strain curve for material under
load.
07
OR
(c) Draw the stress strain curve for material exhibiting following
properties:
(i) Stiff, ductile and strong
(ii) Stiff, brittle and strong
(iii) Stiff, ductile and weak
(iv) Stiff, brittle and weak
(v) Flexible, brittle and strong
(vi) Flexible, ductile and weak
(vii) Flexible, brittle and weak
07
Q.3 (a) Show diagrammatically eutectic and peritectic reaction in metals. 03
(b) Describe oxy-fuel welding. 04
(c) Answer the following with the help of eutectic phase diagram of Sn-
Pb alloy shown below:
(i) The melting point of Sn and Pb.
(ii) Maximum solubility of Sn in Pb and Pb in Sn.
(iii) For a 40 wt% Sn ?60 wt% Pb alloy at 150
0
C (300
0
F),
1) What phase(s) is (are) present?
2) What is (are) the composition(s) of the phase(s)?
3) The relative amount ofeach phase present?
07
www.FirstRanker.com www.FirstRanker.com
www.FirstRanker.com
www.FirstRanker.com
2
OR
Q.3 (a) What are screw threads? 03
(b) What are the information present in production drawing? Discuss
geometric deviation in brief.
04
(c) Write short notes on (i) Pin and cotter joint (ii) Half sectional view
(iii) Metric thread
07
Q.4 (a) Draw the cooling curve of pure iron. 03
(b) What are the conventions to draw sectional lines? Draw different
types of sectional lines.
04
(c) What is annealing? Describe annealing for ferrous and non ferrous
metals.
07
OR
Q.4 (a) What are composite materials? 03
(b) Draw a assembly drawing of plate heat exchanger. 04
(c) What are natural and synthetic polymers? Describe the mechanism
of polymerization. Write the application of polymers in food
industry.
07
Q.5 (a) What is friction welding? 03
(b) Describe the stages of heat treatment process for metals. 04
(c) Describe the principle, components and application of
(i) Electron beam welding.
(ii) Electric arc welding
07
OR
Q.5 (a) Enlist the sanitary design features of food contact surfaces. 03
(b) Discuss the types of case hardening 04
(c) Describe the food equipment standards with regard to surface
texture and fabrication. Draw acceptable and unacceptable self-
drainage design for tanks and vessels.
07
www.FirstRanker.com www.FirstRanker.com
www.FirstRanker.com
FirstRanker.com - FirstRanker's Choice
This post was last modified on 20 February 2020